Bently Nevada 330101-00-29-10-02-00 Proximity Probe – 3300 XL Series

Bently Nevada 330101-00-29-10-02-00 — 8mm Eddy-Current Proximity Probe for High-Speed Rotating Machinery Protection

The Bently Nevada 330101-00-29-10-02-00 is an 8mm diameter, non-contact eddy-current proximity probe belonging to the 3300 XL Series. It is designed for continuous shaft radial vibration and axial position measurement on critical rotating machinery in process industries. Unlike capacitive or optical displacement sensors, the eddy-current transduction principle operates without physical contact, making it immune to shaft surface contamination from oil mist, steam condensate, or process fluid carryover. The probe generates a high-frequency oscillating electromagnetic field at its tip; when a conductive target (typically AISI 4140 steel) enters this field, eddy currents are induced, loading the oscillator circuit and producing a DC-proportional voltage output at the paired Proximitor® sensor. This output is linear across a calibrated gap range of 0.25 mm to 2.25 mm, with a scale factor of 7.87 V/mm (200 mV/mil), traceable to the OEM calibration standard.

Within a machinery protection architecture, this probe occupies the first stage of the signal chain: mechanical displacement → electromagnetic transduction → conditioned DC voltage → monitor card input. Its frequency response of DC to 10,000 Hz covers all sub-synchronous, synchronous, and super-synchronous vibration components encountered in industrial turbomachinery, including oil-whirl instability (typically 0.43–0.48× running speed), blade-pass frequencies, and gear mesh harmonics. The 8mm form factor is the preferred diameter for API 670-compliant installations where bearing housing geometry precludes the use of 11mm probes but where the 5mm probe’s reduced linear range (0.25–1.27 mm) is insufficient for the required gap clearance.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330101-00-29-10-02-00 probe tip houses a precision-wound coil embedded in a thermally stable epoxy matrix. The coil forms the inductive element of a Colpitts-type oscillator circuit resident in the paired 3300 XL Proximitor® sensor. At nominal gap, the oscillator operates at approximately 1 MHz; as the conductive target approaches, eddy-current losses increase, reducing oscillator amplitude. The Proximitor demodulates this amplitude variation and outputs a calibrated DC voltage. This architecture places all active electronics outside the probe body, which is a deliberate thermal isolation strategy: the probe tip can sustain +177°C continuously without degrading oscillator stability, because the temperature-sensitive active components are located in the Proximitor, which is mounted in a cooler instrument enclosure.

The armor-jacketed coaxial cable between probe and Proximitor is a critical EMC element. The outer armor provides a Faraday shield against radiated interference from variable-frequency drives (VFDs), high-current bus bars, and RF sources common in industrial plants. The coaxial geometry maintains a controlled characteristic impedance, preventing signal reflections that would introduce measurement error at high vibration frequencies. The cable jacket material is rated for continuous immersion in turbine lube oil and resistance to steam condensate, ensuring signal integrity in the wet, contaminated environments typical of bearing pedestals.

Thread engagement and probe holder geometry are engineered to maintain axial alignment within ±0.5° of the shaft centerline. Angular misalignment beyond this tolerance introduces a cosine error in the gap measurement, which at 2° misalignment produces approximately 0.06% scale factor deviation — negligible for most applications but relevant in high-precision axial position measurements where trip setpoints are within 0.1 mm of the linear range boundary.

System Integration Benefits

• Direct API 670 compliance: The 330101-00-29-10-02-00 meets API 670 5th Edition probe performance requirements without supplemental calibration, reducing commissioning documentation burden for machinery protection system audits.
• Drop-in 3300 XL compatibility: Electrically and mechanically interchangeable with all 3300 XL probe variants of the same diameter; no Proximitor recalibration or setpoint adjustment required when replacing a failed probe in an existing loop.
• Deterministic DC output: The DC-proportional voltage output integrates directly into Bently Nevada 3500 Series monitor cards, DCS analog input modules (4–20 mA via transmitter), and SCADA historian tags without signal conditioning latency, preserving sub-millisecond measurement determinism.
• Wide frequency coverage: DC–10,000 Hz bandwidth captures all machinery fault signatures within a single transducer, eliminating the need for separate velocity or acceleration sensors for low-frequency orbit analysis.
• Non-contact operation: Zero mechanical wear on the probe tip over the service life; mean time between replacement is governed by cable fatigue and environmental degradation, not contact wear, supporting multi-year continuous operation intervals.
• Diagnostic transparency: The gap voltage output provides a direct, real-time indicator of probe-to-shaft clearance. A slow drift in DC gap voltage between maintenance intervals indicates shaft centerline migration, bearing wear, or thermal growth — actionable diagnostic data without additional instrumentation.
• Hazardous area adaptability: The 330101 series is available in ATEX/IECEx-rated configurations for Zone 1/Zone 2 installations; the standard variant is FM and CSA approved for Class I, Division 2 locations, covering the majority of petrochemical and refinery applications.
• Thermal stability across process extremes: The –35°C to +177°C probe tip rating covers cryogenic LNG compressor service at the low end and high-pressure steam turbine casing installations at the upper end, within a single part number, reducing spare parts inventory complexity.

Quality Assurance & Global Logistics

Every 330101-00-29-10-02-00 unit dispatched from our Xiamen, China facility is sourced from verified Bently Nevada authorized distribution channels. Each unit undergoes incoming inspection covering coaxial cable continuity, armor jacket integrity, tip coil resistance measurement, and dimensional verification of thread form and probe tip geometry against OEM datasheet tolerances. A Certificate of Conformance (CoC) is available upon request at no additional charge, with batch traceability records retained for a minimum of five years.

Logistics from Xiamen are structured for industrial procurement timelines. In-stock units ship within 1–2 business days via DHL Express, FedEx International Priority, or UPS Worldwide Expedited, with typical transit times of 3–5 business days to North America and Europe, and 2–4 business days to Southeast Asia. For project-volume orders requiring phased delivery, a consignment arrangement with scheduled release dates can be structured — contact us with your project schedule for a tailored logistics plan. All shipments include commercial invoice, packing list, and country-of-origin documentation suitable for customs clearance in major industrial importing countries.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.