Bently Nevada 330102-00-40-05-02-CN Proximity Transducer – 3300 XL Series

Bently Nevada 330102-00-40-05-02-CN — Eddy-Current Proximity Transducer in Rotating Machinery Protection Loops

The 330102-00-40-05-02-CN is an 8 mm eddy-current proximity probe belonging to Bently Nevada’s 3300 XL transducer family. Within a machinery protection architecture, this unit occupies the sensing node of a three-component measurement chain: probe, extension cable, and Proximitor driver. Its function is to convert the physical gap between probe tip and a conductive target surface into a proportional DC voltage, delivering a continuous, non-contact displacement signal to the monitoring rack with no mechanical wear and no contact hysteresis.

In turbomachinery protection loops — steam turbines, centrifugal compressors, boiler feed pumps — the 330102-00-40-05-02-CN provides the raw displacement data that feeds radial vibration, axial position, and differential expansion channels. The CN suffix designates the China-market certified variant, carrying localized compliance documentation while remaining electrically and mechanically identical to the standard global model. The probe is factory-calibrated to a sensitivity of 7.87 V/mm (200 mV/mil) against AISI 4140 steel targets, eliminating field calibration overhead during commissioning.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330102-00-40-05-02-CN operates on the eddy-current induction principle. The Proximitor driver generates a high-frequency oscillating magnetic field — nominally at 1.0 MHz — through the probe coil. When a conductive target enters the field, eddy currents are induced on the target surface, loading the oscillator circuit and attenuating the field amplitude. The driver’s demodulation stage converts this amplitude variation into a DC output voltage that is linearly proportional to the probe-to-target gap across the specified measurement range.

EMC Design: The probe body is constructed from 316L stainless steel with a PEEK (polyether ether ketone) tip housing, providing both chemical resistance and dielectric isolation of the coil assembly. The integral armored cable uses a double-shielded coaxial construction — inner braid plus outer foil — with drain wire grounded at the driver end only, forming a single-point ground topology that suppresses common-mode noise injection from adjacent power conductors. This architecture maintains signal integrity in environments with high-frequency switching noise from VFDs and IGBT-based drives operating at carrier frequencies up to 16 kHz.

Thermal Stability: The probe coil is wound on a temperature-compensated ferrite former. Sensitivity drift across the full operating range (−35 °C to +121 °C) is specified at less than ±0.5% of full-scale output, which is critical for axial position channels where thermal expansion of the machine casing must be distinguished from actual rotor movement. The Proximitor driver incorporates an internal temperature compensation network that corrects for cable capacitance variation with temperature, maintaining system accuracy without field adjustment.

Intrinsic Safety Architecture: The ATEX Ex ia certification means the driver limits energy delivery to the probe circuit below the ignition threshold of Group IIC gases (hydrogen, acetylene). Zener barrier or galvanic isolator installation in the associated apparatus is required per IEC 60079-14 for hazardous area installations. The probe itself carries no active components, making it inherently safe on the field side of the barrier.

Part Number Decode: The suffix structure 00-40-05-02-CN maps as follows: 00 = standard configuration; 40 = 1.0 m integral armored cable; 05 = 5 mm nominal gap (0.2 in); 02 = M10×1 metric thread; CN = China-market certified variant with localized compliance documentation.

System Integration Benefits

• Direct rack compatibility with Bently Nevada 3300 and 3500 series: The probe’s output impedance and voltage range are matched to the 3300/20 and 3500/42M I/O modules, enabling plug-and-play installation without signal conditioning adapters or range scaling at the rack input card.
• Zero-contact measurement eliminates mechanical wear: Unlike LVDT or contact-type displacement sensors, the eddy-current probe has no moving parts in the measurement path. Mean time between maintenance intervals is determined by environmental factors, not mechanical fatigue, reducing unplanned downtime in continuous-duty machinery.
• DC-coupled output preserves static position data: The −1 to −17 VDC output is DC-coupled, meaning axial position (thrust bearing wear) and slow eccentricity drift are captured alongside dynamic vibration. AC-coupled alternatives lose this static component, requiring separate position sensors for full API 670 compliance.
• Factory sensitivity traceability to NIST standards: Each probe is calibrated on a gap-sensitivity test fixture traceable to NIST length standards. The calibration certificate documents sensitivity at five gap points across the linear range, providing a baseline for periodic verification without removing the probe from the machine.
• Broad frequency response supports high-speed machinery: The 0–10,000 Hz (−3 dB) bandwidth covers the fundamental and first three harmonics of machines running up to 200,000 RPM, including high-speed compressors and turboexpanders where blade-pass frequencies exceed 5,000 Hz.
• Hazardous area certification reduces installation complexity: ATEX Ex ia and FM IS dual certification allows a single part number to be deployed in both Zone 1/Division 1 and Zone 2/Division 2 classified areas, eliminating the need to maintain separate certified and non-certified probe inventories.
• Compatibility with System 1 condition monitoring software: The probe’s output feeds directly into Bently Nevada System 1 via the 3500 rack’s Ethernet gateway, enabling trend logging, alarm management, and predictive maintenance analytics without additional signal conversion hardware.
• Metric thread and MIL-spec connector standardization: The M10×1 thread and MIL-C-5015 connector are consistent across the 3300 XL family, allowing probe replacement without modifying the mounting boss or rewiring the junction box — a significant advantage during planned turnaround maintenance windows where schedule compression is critical.

Quality Assurance & Global Logistics

Every 330102-00-40-05-02-CN unit supplied through siemensplc.com is sourced from authorized Bently Nevada distribution channels or verified OEM-surplus inventory with full chain-of-custody documentation. Pre-shipment inspection covers visual examination of the probe tip and cable armor, dimensional verification of the M10×1 thread, continuity and insulation resistance testing of the coaxial cable, and functional gap-voltage verification against the factory calibration curve.

Units are shipped from our Xiamen, China warehouse in original or equivalent ESD-safe packaging with desiccant and foam-lined transit cases. Standard export documentation includes commercial invoice, packing list, and Certificate of Conformance. ATEX/FM certification documentation is included for hazardous-area orders. Typical dispatch lead time for in-stock units is 1–3 business days. International shipments are handled via DHL Express, FedEx International Priority, or UPS Worldwide Expedited, with tracking provided at time of dispatch. Air freight to major industrial hubs in Europe, Southeast Asia, the Middle East, and the Americas typically achieves 3–7 business day door-to-door transit. For urgent plant shutdowns or emergency MRO requirements, same-day dispatch is available for orders confirmed before 14:00 CST.

All units carry a 12-month warranty from date of shipment covering manufacturing defects and calibration drift beyond specification. Warranty claims are processed with replacement dispatch within 5 business days of defective unit receipt and inspection.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.