Bently Nevada 330881-28-00-145-03-02 Proximity Transducer Assembly

330881-28-00-145-03-02 PROXPAC XL — Stop the Clock on Your Unplanned Shutdown

Every hour a critical turbine or compressor sits idle costs your plant tens of thousands of dollars. When your Bently Nevada proximity transducer fails, the window between a fault alarm and a full production halt is measured in minutes — not days. The 330881-28-00-145-03-02 PROXPAC XL Proximity Transducer Assembly is in stock at our Xiamen warehouse right now. We ship same day. Your machine gets back online. That’s the only metric that matters.

This is a factory-original Bently Nevada 3300 Series eddy-current proximity transducer assembly — not a clone, not a refurb, not a grey-market substitute. The complete cable-integrated assembly covers a 28-inch probe cable and 145-inch extension, pre-matched and ready to drop into your existing 3300 XL Proximitor loop without recalibration of the driver module.

⚡ URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

Field experience with the 3300 PROXPAC XL points to a consistent set of failure modes. Before you pull the assembly, confirm which fault you’re actually chasing:

Fault Code 01 / Gap Voltage Out of Range: The most common call-out. The Proximitor output sits outside the −10 to −18 VDC window. Nine times out of ten this is a probe tip contamination issue or a cracked probe body from a rub event. Check the gap voltage at the Proximitor terminal first — if it reads near −24 VDC (rail), the probe coil is open. If it reads near 0 VDC, the cable shield is shorted to ground. Either way, the assembly needs replacement, not adjustment.

Fault Code 02 / Not OK (NOK) Relay Tripped: Before condemning the transducer, verify the Proximitor power supply is delivering a stable −24 VDC ±1 V. A sagging power rail will throw a false NOK. If supply voltage is confirmed good, swap the assembly. Do not attempt to re-gap a PROXPAC XL in the field — the probe and extension cable are factory-matched as a set. Mixing cables from different assemblies invalidates the calibration curve.

Replacement Procedure — Key Steps:

• De-energize and tag out the Proximitor module before disconnecting any coaxial connectors. Floating coax on a live Proximitor can induce a false trip on adjacent channels.
• Record the existing gap voltage before removal. Target gap for 8mm probes is typically −10.4 VDC ±0.5 V at 1.0 mm air gap. Use this as your baseline when setting the new assembly.
• Do not over-torque the probe tip. Bently Nevada specifies finger-tight plus 1/4 turn for the probe mounting nut. Excess torque cracks the ceramic tip and shifts the calibration.
• Cable routing matters. Keep the extension cable away from high-voltage conductors and motor leads. Induced noise on the coax will appear as a broadband vibration floor elevation in your System 1 trend data.
• Post-installation check: Verify gap voltage, confirm OK relay status, and perform a slow-roll vibration check before returning the machine to service. Log the new serial number in your CMMS against the asset tag.

Firmware / Driver Matching Note: The 330881-28-00-145-03-02 is calibrated for the standard 3300 XL 8mm Proximitor. If your site has upgraded to the 3500/42M or 3500/44M monitor cards, verify the input channel is configured for the correct transducer type in the rack configuration software before commissioning. A mismatch in the transducer type setting will produce a scale error of up to 15% on the vibration reading — enough to mask a real fault or generate nuisance trips.

Reliability in Harsh Conditions

The PROXPAC XL assembly is built for environments that destroy lesser sensors. The probe tip ceramic withstands continuous exposure to process fluids, bearing oil mist, and shaft temperatures up to 177°C without drift. The coaxial cable jacket is rated for continuous flexing in high-vibration installations — a critical spec in compressor trains where the cable runs through a gland into a pressurized bearing housing.

Bently Nevada’s eddy-current technology is inherently immune to the contamination that kills optical and capacitive sensors. Oil film, condensation, and light surface rust on the shaft target do not affect measurement accuracy. The non-contact measurement principle means zero mechanical wear — the sensor has no moving parts to fatigue. In gas turbine applications where bearing housing temperatures routinely exceed 120°C and vibration levels during startup can hit 50 g, the PROXPAC XL maintains measurement linearity within ±0.5% of full scale.

Every assembly leaving our warehouse has been inspected for cable sheath integrity, connector seating, and label traceability. Units showing any sign of prior installation — thread marks on the probe tip, connector wear, or cable kinking — are rejected. You receive a clean, uninstalled assembly with the original Bently Nevada factory serial number intact.

Global Express Logistics

Our Xiamen warehouse is positioned for rapid export to every major industrial region. When your plant is down, air freight is the only conversation worth having.

• DHL Express Worldwide: Xiamen to Houston, Rotterdam, Dubai, Singapore — typically 2–4 business days door to door. We book the shipment, generate the AWB, and send you tracking within 2 hours of dispatch confirmation.
• FedEx International Priority: Available for destinations where DHL coverage is limited. Same-day booking on orders confirmed before 15:00 CST.
• Export Documentation: Commercial invoice, packing list, and certificate of origin issued for every shipment. HS Code 9026.80 applies to proximity transducer assemblies — we handle the classification so your customs broker doesn’t have to chase paperwork.
• Dangerous Goods: This assembly contains no lithium batteries, no hazardous materials, and no restricted substances under IATA regulations. No special handling surcharges.
• Urgent Plant Shutdown Protocol: Contact us via WhatsApp with your plant name, required quantity, and delivery airport. We will confirm stock, provide a freight quote, and issue a proforma invoice within 30 minutes during business hours.

Contact Information

📧 Email: [email protected]
📱 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.