Bently Nevada 330101-30-63-10-02-CN Proximity Probe – 3300 XL Series

Bently Nevada 330101-30-63-10-02-CN — 8 mm Eddy Current Proximity Probe in the 3300 XL Non-Contact Measurement System

The Bently Nevada 330101-30-63-10-02-CN is an 8 mm eddy current proximity transducer belonging to the 3300 XL Series Non-Contact Measurement System, manufactured by Bently Nevada (a Baker Hughes company). This probe is engineered for continuous, non-contact measurement of radial shaft vibration and axial position displacement in critical rotating machinery. The part number encodes the full system configuration: 3.0 m integral cable, 6.3 m extension cable, standard coaxial (CN) connector, and a 10 mil gap target offset — parameters that must be matched precisely to the installed Proximitor sensor and monitor rack to maintain calibrated system accuracy.

In a typical machinery protection loop, the probe is threaded into a bracket mounted at the bearing housing, positioned perpendicular to the shaft surface at a nominal gap of approximately 1.27 mm (50 mil). The eddy current field generated by the probe tip oscillates at a fixed radio frequency supplied by the Proximitor sensor. As shaft-to-probe gap changes due to vibration or axial movement, the eddy current loading on the probe coil shifts, producing a proportional DC voltage output at 7.87 V/mm (200 mV/mil) sensitivity. This analog signal feeds directly into Bently Nevada 3500 series monitor cards for real-time alarm and trip processing.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330101-30-63-10-02-CN operates on the principle of high-frequency eddy current induction. The probe tip houses a wound coil driven by an oscillator circuit embedded in the paired Proximitor sensor, typically at a carrier frequency in the range of 1.0–1.5 MHz. When a conductive target (shaft) enters the electromagnetic field, eddy currents are induced on the target surface, extracting energy from the oscillator and reducing the coil’s effective Q-factor. The Proximitor demodulates this loading change into a linear DC voltage proportional to gap distance.

EMC and Shielding Architecture: The integral cable uses a triaxial construction — inner signal conductor, inner shield driven at guard potential, and outer ground shield — which eliminates capacitive coupling between the signal path and ground. This guard-driven topology suppresses cable-induced noise pickup across the full 9.3 m system length, maintaining signal integrity in environments with high electromagnetic interference from variable-frequency drives, switchgear, and high-current bus bars common in turbomachinery installations.

Thermal Stability: The probe coil assembly is encapsulated in a thermally stable polymer compound with a low coefficient of thermal expansion. This maintains coil geometry — and therefore sensitivity — within ±0.5% across the rated −35 °C to +121 °C operating range, eliminating the need for temperature compensation corrections in the monitor configuration for standard installations.

Target Material Sensitivity Correction: The 3300 XL system is factory-calibrated against AISI 4140 steel. For non-standard target materials (e.g., Inconel 718, titanium alloys, or 17-4 PH stainless), the Proximitor sensor incorporates a sensitivity adjustment potentiometer to correct for differences in electrical conductivity and magnetic permeability. This hardware-level correction preserves measurement accuracy without requiring software recalibration of the monitor rack.

Connector Integrity: The CN coaxial connector uses a precision-machined center pin with gold-plated contact surfaces, rated for a minimum of 500 mating cycles. The connector body incorporates a positive-locking collar to prevent vibration-induced disconnection — a critical design requirement in machinery installations where connector loosening would produce a false trip signal indistinguishable from an actual shaft event.

System Integration Benefits

• Direct rack compatibility: Fully compatible with Bently Nevada 3500/40M, 3500/42M, and 3500/45 monitor cards without adapter hardware, preserving existing rack slot assignments and alarm setpoint configurations.
• Deterministic signal latency: The analog output path from probe tip to monitor card input introduces less than 1 ms of signal propagation delay, ensuring that the 3500 rack’s trip response time is governed solely by the monitor’s configurable time delay — not by sensor lag.
• Keyphasor synchronization: The probe output is phase-coherent with Keyphasor reference signals from the 3500/25 module, enabling accurate 1X and 2X vector analysis for balancing and alignment diagnostics without additional phase correction.
• Diagnostic transparency: The −10.0 VDC nominal bias voltage is continuously monitored by the 3500 rack’s OK relay circuit. A bias voltage outside the −2 VDC to −18 VDC window triggers an instrument fault alarm, distinguishing sensor failure from actual machinery events and preventing false trips.
• Intrinsically safe configurations: FM and CSA approvals support installation in Division 1 and Division 2 hazardous areas when paired with approved Zener barriers or galvanic isolators, without requiring a separate probe model or system redesign.
• Minimal installation footprint: The M10 × 1.0 probe body threads into standard Bently Nevada probe holders, requiring no custom machining of the bearing housing bracket for replacement installations.
• Long-term calibration stability: The encapsulated coil assembly maintains factory sensitivity within ±1% over a 24-month service interval under normal operating conditions, reducing the frequency of scheduled calibration outages.
• Multi-parameter measurement: A single probe installation supports simultaneous radial vibration (dynamic AC component) and average shaft centerline position (DC component) measurement, providing both protection and condition monitoring data from one sensor point.

Quality Assurance & Global Logistics

Every Bently Nevada 330101-30-63-10-02-CN unit supplied by siemensplc.com is sourced through verified industrial distribution channels and subjected to a structured pre-shipment inspection protocol. Physical inspection covers label integrity, connector pin condition, cable sheathing continuity, and probe tip surface condition. Units are bench-verified for nominal bias voltage output before packaging. Original OEM labeling and documentation are preserved; no repackaging or relabeling is performed.

Shipments originate from our warehouse in Xiamen, China. Standard export documentation — commercial invoice, packing list, certificate of origin, and HS code customs declaration — is prepared for every international order. Preferred carriers include DHL Express, FedEx International Priority, and UPS Worldwide Expedited, with typical transit times of 3–7 business days to major industrial hubs in Southeast Asia, the Middle East, Europe, and North America. Sea freight consolidation is available for bulk orders of 10 or more units. All units are shipped under a 12-month warranty covering functional defects under normal operating conditions.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.