Bently Nevada 330104-00-06-50-12-05 Proximity Probe

330104-00-06-50-12-05 — Stop the Clock on Your Downtime. Ship Today.

Every hour a critical turbine, compressor, or motor sits idle because of a failed proximity probe, your plant is bleeding money. The Bently Nevada 330104-00-06-50-12-05 — a 3300 XL 8mm eddy-current proximity probe with 6-inch integral cable — is one of the most frequently replaced components in API 670 machinery protection systems. We stock it. We ship it fast. From Xiamen to your site, DHL or FedEx, door to door.

This is not a grey-market listing. Every unit we ship is sourced from verified channels, physically inspected, and bias-voltage tested before it leaves our warehouse. If your monitor is throwing a Not OK or your DCS is flagging a gap voltage fault, this is the part you need — and we have it ready.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

Common fault signatures that point to a failed 330104-00-06-50-12-05:

• Gap voltage out of range — Your proximitor (e.g., 330180) should output between −10 VDC and −18 VDC at normal operating gap. A reading outside this window — especially near 0 V or rail voltage — almost always means a probe or cable failure, not a shaft problem.
• Not OK (NOK) relay tripped with no process upset — If the machine is running normally but the monitor channel has gone NOT OK, disconnect the probe at the proximitor and measure the open-circuit voltage. If it reads 0 V or −24 V with no intermediate value, the probe coil is open or shorted.
• Intermittent vibration spikes on a clean machine — Micro-fractures in the integral cable near the probe tip are a known failure mode on probes installed in high-vibration zones. Flex the cable gently while watching the gap voltage on a meter. Any flicker confirms cable integrity failure.
• Sudden sensitivity shift — If your vibration readings have drifted upward or downward without any mechanical change, the probe coil inductance may have shifted due to thermal cycling. Replace the probe and re-gap.

Step-by-step replacement procedure:

1. Isolate the channel. Bypass or inhibit the monitor channel in your DCS/SIS before pulling the probe. Do not trip the machine on a maintenance action.
2. Record the existing gap voltage. Note the current DC output from the proximitor before disconnecting. This is your baseline for re-gapping the new probe.
3. Remove the probe. The 330104 uses a standard 8mm threaded body. Back it out carefully — do not rotate the integral cable. Use the probe body flats only.
4. Inspect the target area. Check the shaft surface for scoring, rust, or runout damage. A damaged target will corrupt readings regardless of probe condition.
5. Install the new probe. Thread in by hand first, then set gap. For AISI 4140 steel targets, the nominal gap is 50 mil (1.27 mm), which should produce approximately −12 VDC at the proximitor output. Adjust in 5-mil increments and verify voltage at each step.
6. Verify the full system cable length. The 330104-00-06-50-12-05 has a 6-inch integral cable. Your extension cable (330130 series) must bring the total system to either 5 meters or 9 meters for the calibrated 200 mV/mil sensitivity to hold. Mismatched cable length = wrong sensitivity = wrong vibration readings.
7. Confirm proximitor model compatibility. This probe is designed for the 3300 XL 8mm proximitor (e.g., 330180-X0-05). It is also compatible with Bently Nevada 3500 series monitors using the same proximitor. Do not mix with 5mm or 14mm probe systems.
8. Re-enable the channel and verify OK status. Gap voltage should be stable within ±0.5 VDC of your pre-replacement baseline. If the NOK condition persists, suspect the extension cable or proximitor next.

Non-standard target materials: If your shaft is Inconel, titanium, or 316 stainless, the standard calibration does not apply. You will need a material correction factor or a custom-calibrated probe. Contact us — we can advise on the correct configuration.

Reliability in Harsh Conditions

The 3300 XL probe body is built for environments that destroy lesser sensors. The 330104-00-06-50-12-05 has been deployed in some of the most punishing industrial settings on the planet — and it holds up because of deliberate engineering choices, not marketing claims.

The probe tip and body are constructed from corrosion-resistant stainless steel, rated for continuous immersion in oil mist and condensate environments common in compressor trains and gearbox housings. The integral cable uses a 50 Ω coaxial construction with a braided EMI/RFI shield — critical in environments where VFDs, large motors, and high-current bus bars generate significant electromagnetic interference that can corrupt vibration signals on unshielded cables.

Thermal performance is a genuine differentiator. The probe maintains its calibrated sensitivity from −35°C to +121°C without field recalibration. In steam turbine applications where bearing housing temperatures routinely exceed 80°C, this stability is not optional — it is the difference between a reliable protection system and one that generates nuisance trips or, worse, misses a real fault.

Vibration resistance is validated to levels consistent with API 670 Annex D requirements. The probe body and cable termination are designed to withstand the broadband vibration spectrum present at bearing housings on large rotating machinery — including the high-frequency content from gear mesh and blade pass frequencies that can fatigue inferior cable assemblies within months.

Ingress protection is achieved through the threaded probe body seal and the integral cable jacket construction. The assembly is suitable for outdoor installations and wash-down environments without additional enclosure protection at the probe itself.

Global Express Logistics

Our warehouse is located in Xiamen, China — a major international shipping hub with direct DHL and FedEx express lanes to North America, Europe, the Middle East, and Southeast Asia. For emergency replacement orders, this geography matters: Xiamen to Frankfurt is 3 business days. Xiamen to Houston is 4 business days. Xiamen to Singapore is next-day.

Standard export process for the 330104-00-06-50-12-05:

• Order confirmation to dispatch: Under 24 hours for in-stock units. We do not batch-process emergency orders — your shipment is picked, packed, and handed to the carrier the same business day for orders placed before 16:00 CST.
• Export documentation: Commercial invoice, packing list, and certificate of origin are prepared for every shipment. HS Code 9031.80 applies to proximity probes. We handle all export classification — you receive a clean, customs-ready package.
• Carrier options: DHL Express Worldwide and FedEx International Priority are our primary carriers. Both provide real-time tracking from pickup to delivery. For time-critical shipments, we can arrange Saturday delivery in most major markets.
• Insurance and liability: All shipments are covered for declared value. For high-value orders, we recommend full declared-value insurance — available at checkout or by request.
• Import duties: We declare accurate commercial values. We do not under-declare. Your customs broker or our freight forwarder can provide HS code documentation for duty pre-calculation in your country.

If your plant is down and you need a confirmed delivery date before placing an order, contact us directly. We will give you a carrier-confirmed transit time estimate before you commit.

Contact Information

📧 Email: [email protected]
💬 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.