Bently Nevada 330104-03-09-50-02-00 Proximity Transducer

330104-03-09-50-02-00 In Stock — Cut Your Downtime Before It Cuts Your Margin

Every hour a critical turbomachine sits idle costs real money — lost throughput, emergency labor, contractual penalties. When your 3300 XL proximity transducer system fails at 02:00 on a Sunday, you don’t need a catalog. You need a part on a plane. The Bently Nevada 330104-03-09-50-02-00 is on our shelf in Xiamen right now, inspected, boxed, and ready for DHL Express pickup today.

This is a 100% genuine Bently Nevada (Baker Hughes) OEM assembly — not a clone, not a rebranded substitute. The complete matched set: 5 mm eddy-current probe, 9 m coaxial extension cable, and 3300 XL 8 mm driver/oscillator, factory-calibrated as a unit at 200 mV/mil. Swap it in, gap it per Installation Manual 141078, and your monitor is back online.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

Ten years of field calls on 3300 XL systems teach you the same failure patterns over and over. Here’s what to check before you pull the trigger on a full system swap — and what to watch when you install the 330104-03-09-50-02-00.

Common fault presentations and root causes:

• OK LED off / Not OK relay de-energized at power-up: Nine times out of ten this is a gap error, not a dead probe. Measure DC output at the driver terminal. If it reads below –1 V or above –21 V, the probe is either too close, too far, or the target surface is wrong material. Re-gap to the midpoint of the linear range (~1.25 mm / 50 mil) before condemning the transducer.
• Intermittent vibration spikes with no process change: Check the extension cable armor for micro-fractures at the probe-end bend radius. Armored coax that has been flexed repeatedly in a tight conduit run develops internal shield breaks that show up as high-frequency noise bursts. Wiggle the cable near the probe while watching the monitor — if the signal jumps, the cable is the culprit, not the probe tip.
• Slow drift in DC gap voltage over weeks: Thermal cycling of the probe tip in high-temperature service above 120°C can shift the scale factor by 2–4%. If your gap hasn’t changed mechanically but the DC output is creeping, verify probe tip temperature and apply the material/temperature correction factor from Bently Nevada Application Note AN-028.
• Driver output stuck at –24 V (rail): Open circuit in the extension cable or probe coil. Disconnect the extension cable at the driver and measure impedance at the probe end. A healthy 5 mm probe reads approximately 100 Ω at 1 kHz. Open or shorted coil means the probe is failed — order the complete matched set, not just the probe.
• 3500 monitor showing Transducer Not OK after replacement: Confirm the monitor card ordering suffix includes the XL transducer option. Standard 3300 (non-XL) and 3300 XL drivers have different oscillator frequencies. Mixing them causes persistent Not OK even with a perfect gap.

Replacement procedure — field checklist:

1. De-energize the monitor channel and lock out the –24 VDC supply to the driver.
2. Document the existing gap voltage before disconnecting — photograph the monitor display.
3. Remove the old probe, extension cable, and driver as a matched set. Never mix components from different calibrated systems.
4. Install the new 330104-03-09-50-02-00 system. Route the extension cable with a minimum bend radius of 50 mm; avoid sharp bends at the probe-end connector.
5. Set initial gap to 1.25 mm (50 mil) using a feeler gauge or dial indicator. Energize the driver and verify DC output is between –10 V and –12 V (midrange).
6. Fine-adjust gap to match the original documented value. Confirm OK relay energizes and the monitor channel clears.
7. Perform a static calibration check: move the probe tip through the linear range and verify output tracks at 200 mV/mil ± 2%.
8. Log the new system serial number and calibration date in your CMMS. The probe, cable, and driver serial numbers must be recorded as a matched set.

Compatibility note on 3500 series monitors: This 3300 XL system is electrically compatible with 3500 monitor cards ordered with the XL transducer option. If your 3500 card was ordered for standard 3300 transducers, the oscillator frequency mismatch will prevent proper operation. Check the monitor card model number suffix before ordering.

Reliability in Harsh Conditions

The 330104-03-09-50-02-00 was not designed for a clean lab. It was designed for the bearing housing of a 40 MW steam turbine running at 3,000 RPM in a refinery that hasn’t had a planned shutdown in 18 months. The engineering margins built into this system are what make it the default choice for API 670 protection systems globally.

The probe tip operates continuously at up to 177°C — hot enough to destroy the insulation on most industrial sensors, but within the rated envelope of the 3300 XL ceramic-filled probe body. The stainless steel armor on the extension cable absorbs the mechanical abuse of cable trays, conduit runs, and the occasional impact during maintenance walks. IP67 sealing on the probe assembly means condensation, wash-down water, and process fluid splatter don’t reach the coil.

Vibration immunity is a non-issue for a non-contact sensor — there are no moving parts to fatigue. The eddy-current coil has no mechanical wear mechanism. Units installed in the 1990s remain in service in power plants that have never replaced them. What fails is almost always the cable, not the probe. That’s why the armored extension cable in this system is a meaningful specification, not a marketing bullet point.

The driver/oscillator electronics are potted and sealed for operation in ambient temperatures from –35°C to +85°C. Drivers mounted in field junction boxes in tropical climates or desert environments regularly see 60–70°C ambient. The thermal design handles it without derating. ATEX Ex ia IIC T6 certification means the system can be installed in Zone 0 and Zone 1 hazardous areas — gas turbine enclosures, compressor buildings, and offshore platform machinery spaces — without additional intrinsic safety barriers in most configurations. Verify your specific installation against the ATEX certificate conditions of use before commissioning.

Global Express Logistics

Our warehouse is in Xiamen, Fujian — one of China’s primary export hubs with direct DHL Express and FedEx International Priority pickup routes operating seven days a week. Orders confirmed before 14:00 CST ship same day. Here’s what that looks like in practice:

• Day 0 (order confirmed): Unit pulled from shelf, inspected, packed in anti-static foam with calibration documentation. DHL/FedEx label generated and handed to courier.
• Day 1–2 (Southeast Asia, Japan, Korea, Australia): DHL Express delivery. Most shipments arrive within 48 hours of dispatch.
• Day 2–3 (Europe, Middle East, India): FedEx International Priority or DHL Express. We pre-fill all commercial invoice fields with correct HS codes and declared values to minimize customs broker delays.
• Day 2–4 (North America): DHL Express or FedEx International Priority. US Customs entry is typically same-day for correctly documented industrial components under $2,500 USD.
• Day 3–5 (South America, Africa): Routing via hub airports in Frankfurt, Dubai, or Miami adds one transit day. We recommend FedEx for Brazil and DHL for sub-Saharan Africa based on clearance reliability.

All shipments include a tracking number sent to your email within 2 hours of dispatch. For critical shutdowns, contact us via WhatsApp for real-time shipment status updates. Saturday pickup and Sunday delivery are available in most major markets for an express surcharge — ask when you place your order.

Export documentation provided as standard: commercial invoice, packing list, certificate of origin, and ATEX/FM compliance documentation on request. Payment by T/T, PayPal, or credit card. No minimum order quantity.

Contact Information

📧 Email: [email protected]
💬 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.