Bently Nevada 330130-130-02-05 Proximity Transducer System – 3300 XL Series

Bently Nevada 330130-130-02-05: Eddy-Current Proximity Transducer System for Turbomachinery Shaft Monitoring

The Bently Nevada 330130-130-02-05 is a factory-matched, three-component eddy-current proximity transducer system belonging to the 3300 XL Series — the platform that established the global reference standard for non-contact shaft displacement measurement in rotating machinery protection. This specific configuration pairs a 25 mm (1-inch) diameter probe with a 2-metre armored probe cable and a 5-metre extension cable, yielding a total signal path of 7 metres from probe tip to driver output. The system operates on the eddy-current induction principle: a high-frequency oscillator within the driver energizes a coil embedded in the probe tip, generating an electromagnetic field that induces eddy currents in any conductive target within range. The resulting impedance change is demodulated into a DC-proportional output voltage — nominally 200 mV/mil (7.87 V/mm) — that directly represents the instantaneous gap between probe face and shaft surface.

In a turbomachinery protection architecture, this output feeds directly into Bently Nevada 3500 Series monitor modules — specifically the 3500/40M, 3500/42M, 3500/44M, and 3500/46M Proximitor/Seismic Monitor cards — where it is processed against user-configured alert and danger setpoints. The system’s DC-to-10,000 Hz frequency response ensures that both quasi-static shaft centerline position changes and high-frequency sub-synchronous instabilities (oil whirl, oil whip) are captured within a single measurement channel, eliminating the need for parallel sensor architectures at different frequency bands.

The -130-02-05 suffix encodes the physical configuration: 130 denotes the 25 mm probe body diameter, 02 specifies the 2-metre probe cable, and 05 specifies the 5-metre extension cable. This cable geometry is the most widely deployed configuration in power generation and oil & gas facilities where the driver/proximitor must be mounted outside the bearing housing pedestal, beyond the thermal and vibration envelope of the machine casing, while the probe itself is threaded directly into the bearing housing bracket at a radial or axial measurement plane.

The 330130-130-02-05 is calibrated as a matched set at the factory. Sensitivity and linearity specifications are guaranteed only when the probe, extension cable, and driver are used together as shipped — substituting any individual component from a different part number invalidates the calibration curve and introduces measurement error that cannot be corrected through software scaling alone. This is a fundamental constraint of eddy-current system physics: the driver’s oscillator circuit is tuned to the combined impedance of the specific probe coil and cable assembly it was matched with during factory calibration.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 3300 XL system architecture resolves four hardware-level engineering constraints that generic eddy-current sensors cannot address in turbomachinery environments.

Thermal Gradient Compensation: The probe body is machined from a thermally stable alloy with a controlled coefficient of thermal expansion. At bearing housing temperatures approaching 150°C, dimensional changes in the probe body along the measurement axis are held within a tolerance that produces negligible apparent gap drift relative to the 80 mil linear range — maintaining measurement accuracy without temperature correction offsets in the monitor software.

EMC Shielding Architecture: The coaxial cable assembly uses a double-shield construction: an inner shield referenced to the driver oscillator ground, and an outer shield bonded to machine frame ground at the driver end only. This single-point grounding topology prevents ground loop currents — endemic in large rotating machinery installations where frame potential differences of several volts are common — from coupling into the measurement signal. The stainless steel armor adds a third layer of protection against high-intensity magnetic fields generated by adjacent motor stators and generator windings.

Driver Oscillator Stability: The Proximitor driver employs a temperature-compensated oscillator circuit that holds excitation frequency within a tight tolerance band across the full -35°C to +85°C operating range. Oscillator frequency drift translates directly to sensitivity drift in eddy-current systems — a 1% frequency shift produces a measurable change in electromagnetic field penetration depth and therefore probe sensitivity. The 3300 XL driver’s oscillator stability specification ensures the 200 mV/mil sensitivity figure remains valid across the full environmental envelope without field recalibration.

Cable Impedance Matching: The 5-metre extension cable is manufactured to a controlled characteristic impedance matched to the driver’s input circuit. At measurement frequencies approaching 10 kHz, unmatched cable impedance introduces phase shift and amplitude error in the demodulated output. The factory-matched calibration process accounts for the specific impedance of this cable length — which is why substituting a different cable length from another part number produces calibration errors that cannot be corrected by simple gain adjustment in the monitor.

System Integration Benefits

• Direct API 670 Compliance: Sensor performance meets API Standard 670 requirements for radial vibration and axial position measurement — eliminating supplementary signal conditioning on new installations or retrofits subject to this code.
• Zero-Latency Analog Output: The driver’s DC-proportional output is available at the terminal block with no digital conversion latency, preserving the full DC-to-10 kHz bandwidth for time-waveform capture and spectrum analysis in System 1 software.
• Deterministic Fault Annunciation: When the probe gap moves outside the linear range — due to shaft contact, probe loosening, or cable fault — the driver output saturates to a defined voltage level that the 3500 monitor interprets as a Not-OK condition, triggering a discrete relay output within one monitor scan cycle.
• Dual-Plane Orbit Analysis Support: Two units mounted at 90° at the same axial plane provide the orthogonal X-Y vibration data required for shaft orbit analysis — the primary diagnostic tool for identifying rotor dynamic instabilities, misalignment, and rub conditions.
• Axial Position Measurement Capability: When mounted against a thrust collar, the same system measures rotor axial displacement at 200 mV/mil sensitivity, enabling a single sensor platform to serve both radial vibration and thrust position monitoring within the 3500 rack architecture.
• System 1 Software Integration: The analog output is the primary data source for Bently Nevada System 1 condition monitoring software, which performs automated spectrum analysis, trend tracking, and alarm management traceable to the calibrated output of this matched transducer system.
• Hazardous Area Deployment Without Signal Barriers: ATEX Zone 1 and FM Division 1 certifications allow direct installation in classified areas without Zener barriers or galvanic isolators, eliminating the signal attenuation and bandwidth limitation that passive barriers introduce.
• Long-Term Spare Parts Interchangeability: Within the 3300 XL family, the 330130 probe sub-family maintains dimensional and electrical interchangeability across production generations — a replacement unit installs in the same bracket, connects to the same driver terminal block, and produces the same calibrated output without monitor card reconfiguration.

Quality Assurance & Global Logistics

Every Bently Nevada 330130-130-02-05 unit supplied by siemensplc.com is sourced through verified industrial supply channels and subjected to a structured pre-shipment verification protocol before dispatch from our Xiamen, China operations center.

Authenticity Verification: Each unit undergoes visual and dimensional inspection against OEM reference documentation — label format, part marking typography, connector body geometry, cable jacket color coding, and armor construction are cross-referenced against known-genuine specimens. Units that fail any inspection criterion are quarantined and not offered for sale.

Functional Bench Test: The system is powered at -24 VDC and driver output voltage is measured across the linear range using a calibrated gap fixture. Output sensitivity is verified against the 200 mV/mil nominal specification. Systems outside the acceptable tolerance band are not shipped.

12-Month Warranty: All units carry a 12-month warranty against defects in materials and workmanship from the confirmed shipment date. Warranty claims are processed with a replacement-first policy for qualified accounts.

Global Logistics from Xiamen: Xiamen is a designated free-trade port with direct air freight connections to industrial hubs across Asia-Pacific, the Middle East, Europe, and the Americas. Standard shipments are dispatched via DHL Express, FedEx International Priority, or UPS Express — typical transit times of 3–5 business days to most destinations. Full export documentation is provided: commercial invoice, packing list, certificate of origin, and MSDS where required. Same-day dispatch is available for in-stock units when orders are confirmed before 14:00 CST.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.