Bently Nevada 330130-40-00-00 Extension Cable – 3300 Series

Bently Nevada 330130-40-00-00 — 40 ft Extension Cable for 3300 Series Proximity Transducer Systems

The Bently Nevada 330130-40-00-00 is a 40-foot (12.2 m) coaxial extension cable engineered for the 3300 Series Proximity Transducer System. Its primary function is to transmit the high-frequency eddy-current oscillator signal from the probe tip to the proximitor/driver with minimal attenuation and zero impedance discontinuity. In rotating machinery protection architectures — where shaft displacement measurements must resolve to sub-micron levels — cable integrity is not a secondary concern; it is a first-order system parameter. This cable is manufactured to Baker Hughes / Bently Nevada factory tolerances and carries full OEM traceability.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330130-40-00-00 operates within a three-component eddy-current measurement chain: probe → extension cable → proximitor. The probe tip generates a 1 MHz oscillating electromagnetic field; the extension cable carries the modulated RF signal to the proximitor, which demodulates it into a DC voltage proportional to the gap between probe tip and target shaft surface. Any impedance mismatch along this path introduces a standing-wave reflection that shifts the linear measurement range and corrupts the gap voltage calibration curve.

Bently Nevada addresses this through a tightly controlled coaxial geometry. The PTFE dielectric maintains a stable dielectric constant (εr ≈ 2.1) across the full operating temperature range, preventing thermally induced impedance drift — a failure mode common in polyethylene-insulated field substitutes. The silver-plated inner conductor minimizes skin-effect resistance at 1 MHz, keeping insertion loss below 0.5 dB over the full 40 ft run. The MIL-C-5015 bayonet connector uses gold-plated contacts with a contact resistance specification of < 5 mΩ, eliminating the micro-ohm-level contact variability that can introduce noise floors above the system’s 25 mV resolution threshold.

From an EMC standpoint, the cable’s braided shield provides > 85 dB of shielding effectiveness at 1 MHz, which is critical in motor control centers and turbine enclosures where variable-frequency drives generate broadband conducted emissions from 2 kHz to 30 MHz. The shield is terminated at the proximitor end only (single-point grounding), preventing ground-loop currents that would appear as low-frequency noise on the vibration channel. This design is consistent with API 670 Annex D grounding requirements and eliminates the need for external ferrite chokes in most installations.

System Integration Benefits

• Deterministic gap voltage linearity: Factory-matched impedance ensures the proximitor’s linear range (typically −10 VDC to −18 VDC) is preserved without recalibration after cable installation.
• Zero-drift temperature performance: PTFE dielectric maintains εr stability from −40 °C to +121 °C, eliminating thermally induced measurement offset in steam turbine bearing housings.
• API 670 compliance out of the box: No field modification required to meet machinery protection standard requirements for cable routing, shielding, and connector type.
• Plug-and-play with 3300 Series probes and proximitors: Connector pinout and cable parameters are factory-verified against 330101, 330103, 330104, and 330105 probe families.
• Reduced diagnostic ambiguity: OEM cable eliminates cable-related variables when troubleshooting abnormal vibration readings, narrowing root-cause analysis to mechanical or process sources.
• Broadband EMI rejection: > 85 dB shielding effectiveness prevents false alarms triggered by VFD switching noise in mixed-signal industrial environments.
• Mechanical durability in high-vibration zones: MIL-C-5015 bayonet locking mechanism withstands continuous vibration up to 15 g without connector loosening, maintaining signal continuity in compressor skid installations.
• Full documentation chain for compliance audits: Each unit ships with a certificate of conformance, OEM part label, and packing documentation — satisfying ISO 55000 asset management and insurance inspection requirements.

Quality Assurance & Global Logistics

Every 330130-40-00-00 unit stocked at siemensplc.com is sourced through verified Baker Hughes / Bently Nevada authorized distribution channels. Pre-shipment inspection covers three checkpoints: (1) connector contact resistance measurement (< 5 mΩ per contact), (2) cable continuity and shield integrity via TDR (time-domain reflectometry) to confirm no impedance discontinuities along the 12.2 m run, and (3) visual inspection of jacket, connector body, and bayonet locking ring for transit damage.

Packaging uses anti-static foam-lined cartons with moisture-desiccant inserts, maintaining cable coil geometry within the manufacturer’s minimum bend radius specification during air and sea freight. Export documentation — including commercial invoice, packing list, certificate of conformance, and HS code 8544.42 classification — is prepared in-house at our Xiamen, China operations center, enabling same-day customs clearance submission for DHL Express and FedEx International Priority shipments. Standard delivery to Southeast Asia: 3–5 business days. Europe and North America: 5–8 business days. Expedited options available upon request.

All units carry a 12-month warranty covering manufacturing defects in materials and workmanship. Warranty claims are processed within 5 business days with advance replacement available for critical plant shutdowns.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.