Bently Nevada 330171-00-08-90-01-05 Proximity Probe – 3300 XL

Bently Nevada 330171-00-08-90-01-05 — 8mm Eddy Current Proximity Probe for Critical Rotating Machinery Protection

The 330171-00-08-90-01-05 is an 8mm diameter eddy current proximity transducer manufactured by Bently Nevada as part of the 3300 XL Proximity Transducer System. It is engineered for continuous, non-contact measurement of radial shaft vibration and axial position displacement in turbomachinery, centrifugal compressors, and high-speed rotating equipment operating under API 670 machinery protection standards.

This specific configuration encodes a 0.9 m (90 cm) integral cable, standard connector termination (code 01), and metric thread probe tip (code 05). The probe operates as the sensing element within a three-component measurement chain: probe body, extension cable, and proximitor/oscillator-demodulator driver. Each component is factory-matched to ensure system-level sensitivity accuracy within ±1% of the nominal 7.87 V/mm (200 mV/mil) scale factor.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330171-00-08-90-01-05 operates on the principle of Faraday-law eddy current induction. The probe coil, driven by a high-frequency oscillator (typically 1.0 MHz carrier frequency within the 3300 XL proximitor), generates an alternating electromagnetic field at the probe tip. When a conductive target surface enters this field, eddy currents are induced on the target surface, loading the probe coil and reducing its effective inductance and Q-factor. The proximitor demodulates this impedance change into a DC voltage proportional to the air gap distance.

EMC and Shielding Architecture: The probe cable employs a coaxial construction with a low-loss dielectric and a continuous braided shield referenced to the proximitor ground. This architecture suppresses common-mode RF interference and prevents capacitive coupling from adjacent high-voltage cabling — a critical requirement in turbine control rooms where variable-frequency drives and high-current bus bars operate in proximity to instrumentation wiring. The shield continuity is maintained through the connector body, which is machined from stainless steel and provides both mechanical strain relief and RF ground bonding.

Thermal Stability: The probe coil former is wound on a ceramic bobbin with a low coefficient of thermal expansion. This minimizes sensitivity drift across the −35°C to +177°C operating envelope. In steam turbine applications where probe tip temperatures can approach 150°C during sustained full-load operation, this thermal stability ensures that the scale factor remains within the ±1% factory tolerance without field recalibration.

Mechanical Integration: The metric thread tip (code 05) allows direct installation into standard M10 × 1.0 probe holders used in European and Asian turbomachinery OEM designs. The probe body is machined from 316 stainless steel, providing resistance to condensate, lube oil mist, and mild acidic atmospheres encountered in compressor seal environments. The integral cable exits through a strain-relief boot that maintains the minimum bend radius and prevents fatigue cracking at the cable-to-body junction under vibration loads up to 20 g.

System Integration Benefits

• Direct 3300 XL System Compatibility: Factory-matched to 3300 XL proximitor drivers (330180 series), eliminating the need for field sensitivity adjustment or scale factor correction when used with the standard AISI 4140 target material.
• API 670 Compliance: Meets the measurement chain accuracy requirements of API Standard 670 (5th Edition) for radial vibration and axial position monitoring on critical and essential machinery, supporting plant insurance and regulatory compliance documentation.
• System 1 / TDIXl Integration: The calibrated output voltage range (−1 to −17 VDC) maps directly to the input conditioning circuits of Bently Nevada System 1 condition monitoring software and TDIXl rack monitors, preserving full diagnostic resolution without signal conditioning adapters.
• 3500 Series Monitor Compatibility: When paired with the appropriate 3500-series driver module (e.g., 3500/42M, 3500/45), the 330171-00-08-90-01-05 provides full-resolution vibration and position data to the 3500 rack, supporting both alarm and trip relay outputs.
• Deterministic Response Latency: The eddy current measurement chain introduces less than 5 ms of signal latency from physical displacement to analog output, meeting the response time requirements for machinery protection trip systems where shaft contact events must be detected within one shaft revolution at operating speed.
• Diagnostic Transparency via Gap Voltage: The DC bias output (nominally −10.5 VDC at mid-range gap) provides a continuous, real-time indicator of probe installation gap. Maintenance personnel can verify probe health and target condition without removing the probe from service, reducing planned maintenance downtime.
• Hazardous Area Deployment: FM and CSA intrinsically safe (IS) variants of the 330171 series are available for Zone 1 / Division 1 classified areas, including hydrogen-cooled generators and hydrocarbon compressor trains, without requiring additional IS barriers in the signal loop.
• Reduced Calibration Overhead: Factory-issued calibration certificates with traceable sensitivity data allow the measurement chain to be accepted as a calibrated instrument assembly, reducing the scope of site calibration procedures during commissioning and periodic turnaround inspections.

Quality Assurance & Global Logistics

Every 330171-00-08-90-01-05 unit supplied by siemensplc.com is sourced as a genuine Bently Nevada original component through verified supply channels. Each unit undergoes incoming inspection including coil impedance verification, cable continuity and insulation resistance testing, and connector integrity checks prior to dispatch. Factory calibration documentation is available upon request and can be provided in PDF format for inclusion in plant instrument records.

Our logistics operations are based in Xiamen, China, a major international port city with direct air freight connections to Singapore, Dubai, Frankfurt, Los Angeles, and Tokyo. Standard international shipments are dispatched within 1–3 business days of order confirmation. Expedited DHL Express and FedEx Priority services are available for critical plant shutdown scenarios, with transit times of 2–5 business days to most global destinations. All shipments are packed in anti-static, moisture-barrier packaging with foam cushioning to protect the probe coil and cable assembly during transit. Export documentation including commercial invoice, packing list, and certificate of origin is prepared for all international orders.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.