Bently Nevada 330171-00-32-05-01-05 Eddy-Current Proximity Probe – 3300 XL Series

Bently Nevada 330171-00-32-05-01-05: 8mm Eddy-Current Proximity Probe in the 3300 XL Transducer System

The 330171-00-32-05-01-05 is an 8mm eddy-current proximity probe manufactured by Bently Nevada (Baker Hughes) as a core sensing element within the 3300 XL Proximity Transducer System. Its primary function in a rotating machinery protection loop is to convert shaft radial displacement into a proportional DC voltage signal — continuously, without mechanical contact, across a bandwidth of DC to 10,000 Hz. This non-contact architecture eliminates wear-induced drift, making it suitable for uninterrupted 24/7 deployment on critical assets including gas turbines, centrifugal compressors, steam turbines, and high-speed pumps operating under API 670 machinery protection mandates.

Within the control loop, the probe acts as the primary transducer: it generates a raw oscillator-modulated signal that is conditioned by a paired Proximitor® sensor (e.g., 330180 series) into a calibrated output of 7.87 V/mm (200 mV/mil). This output feeds directly into a Bently Nevada 3500 Series monitor rack, where trip and alarm setpoints are evaluated in real time. The 5-meter integral armored cable encoded in the part suffix (-05 cable length designation) is factory-matched to the Proximitor® calibration curve, ensuring system linearity is preserved without field recalibration.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330171-00-32-05-01-05 operates on the Lenz’s law induction principle: a high-frequency oscillator (typically 1.0 MHz carrier) drives a coil wound within the probe tip. When a conductive target enters the electromagnetic field, eddy currents are induced on the target surface, loading the oscillator circuit and reducing its amplitude. The Proximitor® sensor demodulates this amplitude variation into a DC voltage proportional to the gap distance between probe face and shaft surface.

EMC Design: The probe body is constructed from 316 stainless steel with a hermetically sealed coil assembly. The integral armored cable uses a double-shielded coaxial construction — inner shield referenced to the oscillator ground, outer shield tied to chassis ground at the Proximitor® — creating a Faraday cage that attenuates externally induced noise to below 1 mV RMS across the operating bandwidth. This architecture maintains signal integrity in environments with high-voltage switchgear, variable-frequency drives, and arc furnaces operating in proximity.

Thermal Stability: The coil former material and winding geometry are selected to produce a temperature coefficient of scale factor below ±0.05% per °C across the rated –35°C to +121°C range. This is critical in turbine bearing housings where ambient temperature can swing 80°C between cold-start and full-load conditions. Without this compensation, a 100°C temperature rise would introduce a 5 mil (127 µm) apparent displacement error in a system with a 200 mV/mil scale factor — sufficient to mask a genuine shaft orbit anomaly.

Mechanical Robustness: The probe tip thread (M10 × 1.0 standard) and locknut design allow precise gap setting during installation. The armored cable jacket resists hydrocarbon fluids, steam condensate, and mechanical abrasion from cable trays, with a minimum bend radius of 50 mm to prevent coaxial impedance discontinuities that would corrupt the oscillator Q-factor.

System Integration Benefits

• Drop-in 3300 XL compatibility: The probe interfaces directly with 330130-series extension cables and 330180-series Proximitor® sensors without any impedance matching or recalibration, preserving the factory-certified system accuracy of ±1% full-scale.
• Deterministic real-time response: The DC-to-10 kHz bandwidth captures both quasi-static position (thrust position, slow-roll runout) and dynamic vibration events (subsynchronous instability, blade-pass frequencies) within a single transducer channel, eliminating the need for separate position and vibration sensors on the same shaft journal.
• API 670 compliance: Accepted by EPC contractors and end-users under international machinery protection standards, simplifying FAT/SAT documentation and insurance underwriting for critical rotating equipment.
• Diagnostic transparency: The linear 7.87 V/mm output allows direct correlation between monitor voltage readings and physical shaft displacement in engineering units, reducing diagnostic ambiguity during alarm investigation.
• Redundant monitoring architectures: Two probes mounted 90° apart on the same journal (X-Y configuration) feed independent monitor channels, enabling orbit plot generation in System 1® software for bearing instability characterization without additional hardware.
• Minimal installation footprint: The 8mm probe tip diameter accommodates tight bearing housing geometries where larger 11mm probes cannot be physically installed, expanding the range of machinery that can be brought into API 670 compliance.
• Long-term calibration stability: The hermetically sealed coil assembly prevents moisture ingress that would alter coil inductance over time, maintaining scale factor within ±2% of nominal across a 5-year service interval under normal operating conditions.
• Interoperability with 3500 Series monitors: Direct electrical compatibility with Bently Nevada 3500/40M, 3500/42M, and 3500/45 monitor modules allows the probe to participate in voted trip logic (2-of-3 or 2-of-4 configurations) for SIL-rated machinery protection loops.

Quality Assurance & Global Logistics

Every 330171-00-32-05-01-05 unit supplied by siemensplc.com is sourced as genuine Bently Nevada (Baker Hughes) hardware. Each unit undergoes a structured pre-shipment verification protocol:

• Visual inspection: Probe tip, housing threads, cable jacket, and connector terminus are examined for mechanical damage, corrosion, and contamination.
• Dimensional verification: Probe tip diameter and thread pitch are confirmed against Bently Nevada published drawings to ensure correct installation fit.
• Electrical continuity check: Center conductor and shield continuity are verified at both ends of the integral cable assembly.
• Packaging: Units are individually wrapped in anti-static foam, sealed in moisture-barrier poly bags with desiccant, and packed in double-wall corrugated cartons rated for international air and sea freight.
• Documentation: Certificate of conformance, packing list, and commercial invoice with HS code 9031.80 are included as standard. Test reports and calibration data are available upon request.

Shipments originate from our warehouse in Xiamen, China. Standard international air freight delivers to major industrial hubs in Southeast Asia, the Middle East, Europe, and the Americas within 3–7 business days. Sea freight consolidation is available for bulk orders. We support EXW, FOB Xiamen, CIF, and DDP Incoterms. Export documentation is prepared in compliance with Chinese customs regulations and destination-country import requirements.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.