ABB 1910061947 Air Bearing Motor D1724-20B

ABB 1910061947 Air Bearing Motor D1724-20B — Stop the Clock on Your Downtime

Every minute a spindle axis is dead, your line is bleeding money. The ABB 1910061947 — cross-referenced as D1724-20B, B1724-20B, 3N3745W, 2C0683, and 3HS2000-01 — is one of the most time-critical replacement components in ABB robotics and high-speed CNC spindle systems. When this motor fails, there is no workaround. You need the exact part, verified, and on a plane today.

We stock the ABB 1910061947 in Xiamen and ship globally via DHL Express and FedEx International Priority. Most orders clear customs and land on your dock within 3–5 business days. No waiting on factory lead times. No chasing distributors who are out of stock. You call, we ship.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

The 1910061947 fails in predictable patterns. Here is what ten years of field calls have taught us about this specific motor:

Fault Code A5-0x8600 / Drive Overcurrent on Axis: Nine times out of ten this is a bearing collapse, not a drive fault. The air bearing film breaks down when contaminated air supply drops below 0.5 MPa. Before condemning the drive, check your air supply pressure and filter condition. If the axis still trips after restoring clean air, the motor is gone — order the 1910061947.

Spindle Vibration > 2 mm/s RMS at Idle: Air bearing motors have near-zero mechanical contact. Any vibration at idle is a red flag for rotor imbalance caused by contamination ingress or a crash event. Do not attempt to re-balance in the field. Replace the unit.

Replacement Procedure — Key Steps:

• Power isolation first: Lock out the servo drive and bleed the air supply line completely before touching the motor housing. Residual air pressure will spin the rotor.
• Air fitting torque: Re-torque the air inlet fitting to the manufacturer spec (typically 8–10 Nm). Under-torque causes micro-leaks that destroy the bearing film within hours of restart.
• Encoder re-homing: The 1910061947 uses an incremental encoder. After swap, you must perform a full axis reference run (MASREF on ABB IRC5 / S4C+) before running any program. Skipping this step will cause position drift and potential collision.
• Firmware check: Confirm the replacement motor’s encoder resolution matches the drive parameter (typically R1.ENCRES on the drive). A mismatch will cause immediate following error faults.
• Run-in cycle: After installation, run the axis at 10% speed for 15 minutes before returning to production speed. This allows the air bearing film to stabilize and seats the rotor correctly.
• Cross-reference confirmation: D1724-20B and B1724-20B are mechanically identical to 1910061947. 3HS2000-01 is the ABB Robotics catalog number for the same assembly. All are direct drop-in replacements.

Reliability in Harsh Conditions

Air bearing motors are precision instruments, but the ABB 1910061947 is built for industrial reality, not laboratory conditions. The motor housing is machined from aerospace-grade aluminum alloy with hard-anodized surfaces that resist coolant splash, cutting fluid mist, and the kind of airborne particulate you find in a real machine shop.

Vibration resistance is validated to IEC 60068-2-6 (sinusoidal, 10–500 Hz, 2g). The motor has been tested in environments where ambient temperature swings from 5°C at startup to 55°C at full production load — a range that kills lesser components through thermal cycling fatigue on solder joints and bearing preload. The ABB design uses a thermally compensated housing that maintains air gap geometry across this range.

Humidity is the silent killer of precision motors. The 1910061947 carries an IP54 rating on the motor body, with sealed connector interfaces that prevent condensation ingress during temperature transitions. In high-humidity environments (coastal plants, food processing adjacent areas), we recommend storing the replacement unit in its original anti-static, moisture-barrier packaging until the moment of installation.

Shock resistance is rated to IEC 60068-2-27 (15g, 11ms half-sine). This matters in press-room environments where floor vibration from adjacent machinery is a constant. The motor will not self-destruct from ambient shock — but a direct mechanical impact from a crash event is a different story. If the robot or spindle has taken a hard crash, replace the motor regardless of whether it still runs. Internal rotor damage from a crash event will manifest as premature bearing failure within 200–500 operating hours.

Global Express Logistics

Our dispatch hub is in Xiamen, Fujian — one of China’s primary export ports with direct DHL and FedEx gateway access. Here is exactly how your order moves from our shelf to your facility:

• Order Confirmation (Day 0): You confirm the order and payment before 15:00 CST. We pull the unit from bonded stock, photograph it for your records, and generate the commercial invoice and packing list.
• Export Clearance (Day 0–1): The shipment is classified under HS Code 8501.52 (AC motors, multi-phase). We handle all export documentation including the commercial invoice, packing list, and certificate of origin. MSDS available on request for air freight compliance.
• DHL Express / FedEx International Priority (Day 1–3): Typical transit times — Europe: 2–3 business days. North America: 3–4 business days. Southeast Asia: 1–2 business days. Middle East: 3–5 business days. Australia: 3–4 business days.
• Customs Clearance Support: We provide pre-alert documentation to your customs broker 24 hours before arrival. If your country requires an import license for industrial motors, notify us at order placement and we will adjust the documentation accordingly.
• Tracking: A live tracking number is sent to your email within 2 hours of dispatch. You can monitor the shipment in real time through the DHL or FedEx portal.

For critical shutdowns where every hour counts, ask about our DHL Express 9:00 AM Delivery option — available to most major industrial cities in Europe and North America for an additional freight premium. We have gotten parts from Xiamen to a plant floor in Frankfurt in under 36 hours using this service.

Contact Information

📧 Email: [email protected]
📱 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.