Bently Nevada 330101-00-26-10-02-05 Proximity Probe

330101-00-26-10-02-05 Proximity Probe — Every Hour of Downtime Costs You Money. We Ship Today.

Your turbine is down. The vibration monitor is throwing a Not OK alarm. Maintenance is standing by. The probe is dead — and you need a verified replacement now, not in three weeks. The Bently Nevada 330101-00-26-10-02-05 is in stock at our Xiamen warehouse. We cut the paperwork, pull the unit off the shelf, and hand it to DHL before your shift ends.

This is not a catalog listing. This is a field-ready spare.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

Ten years on the floor taught me one thing: most probe failures are not the probe. Before you condemn the 330101-00-26-10-02-05, run through this checklist — it will save you a second trip.

Step 1 — Verify the gap voltage first. Power up the Proximitor sensor (330180 or 330185) and measure the DC output at the OK relay terminals. A healthy gap on a 5 mm probe against AISI 4140 steel reads between −10.0 VDC and −18.0 VDC. If you are reading 0 VDC or rail voltage (−24 VDC), the probe tip is either shorted, open-circuit, or the gap is completely wrong. Do not assume the probe is dead until you have confirmed the gap is within the 30–90 mil (0.76–2.29 mm) linear range.

Step 2 — Check the matched system. The 330101-00-26-10-02-05 is a system component, not a standalone sensor. It must be paired with the correct extension cable (330130 series, matching length) and the correct Proximitor sensor. Mixing cable lengths from different system configurations shifts the sensitivity curve and will cause the monitor to flag a false alarm or, worse, mask a real vibration event. When you replace the probe, replace the extension cable at the same time if it has been in service more than five years.

Step 3 — Inspect the connector and cable sheath before installation. The integral armored cable on this probe is 26 inches. In tight bearing housings, technicians often kink the cable at the compression fitting. A kink you cannot see from the outside can fracture the inner conductor and produce an intermittent open-circuit fault that looks like a noisy vibration signal. Run a continuity check from the probe tip to the MIL connector pins before you torque the probe into the housing.

Step 4 — Set the gap correctly. Thread the probe in until the tip just contacts the shaft, then back out 50 mil (1.27 mm) — that puts you in the center of the linear range. Lock the jam nut. Confirm the gap voltage reads approximately −12.5 VDC ± 0.5 VDC. If the monitor is a 3300 XL rack, the OK LED should illuminate within 10 seconds of powering the Proximitor.

Common fault codes on 3300 XL monitors associated with this probe:

• NOT OK (relay de-energized, OK LED off): Gap out of range, open-circuit probe, or failed Proximitor. Measure gap voltage first.
• High vibration alarm with no process change: Probe tip contamination (oil varnish, metallic debris). Remove probe, clean tip with isopropyl alcohol, re-gap.
• Intermittent OK dropout: Loose MIL connector at the junction box, or micro-fracture in the integral cable. Swap the probe and extension cable as a matched set.
• Sensitivity drift over time: Probe tip erosion from shaft rub. Measure sensitivity with a calibration fixture — if it deviates more than ±5% from 200 mV/mil, replace the probe.

Reliability in Harsh Conditions

The 3300 XL probe system was engineered for the environments that destroy ordinary sensors. The 330101-00-26-10-02-05 carries a continuous operating temperature rating of −35 °C to +177 °C — that covers everything from an outdoor compressor station in northern Canada in January to a steam turbine bearing housing running at full load in a tropical refinery. The armored integral cable resists oil mist, process gas condensate, and the mechanical vibration that fatigues unprotected cables within months.

The eddy-current measurement principle is inherently immune to contamination on the probe tip. Unlike optical or capacitive sensors, a thin film of oil or water on the tip surface does not affect the electromagnetic field coupling to the shaft. This is why the 3300 XL system remains the default choice for API 670-compliant machinery protection on critical rotating equipment — turbines, compressors, and pumps where an undetected bearing failure means a catastrophic, unplanned outage.

Units supplied from our Xiamen warehouse are stored in climate-controlled conditions at 20 °C ± 5 °C and 40–60% RH. Each unit is individually bagged with desiccant and inspected for connector integrity and cable sheath condition before dispatch. We do not ship units that show any sign of storage damage, corrosion, or connector pin deformation.

Global Express Logistics

Our Xiamen warehouse sits 40 minutes from Xiamen Gaoqi International Airport (XMN), a major DHL and FedEx hub for southern China. That geography is not an accident — it means your urgent order moves from our shelf to an international flight in the same business day.

Standard dispatch process:

• Order confirmed before 14:00 CST: Same-day dispatch via DHL Express or FedEx International Priority.
• Order confirmed after 14:00 CST: Next business day dispatch.
• Transit times (door-to-door): Southeast Asia 1–2 days | Middle East 2–3 days | Europe 3–4 days | North America 3–5 days | South America / Africa 4–6 days.
• Documentation included: Commercial invoice, packing list, certificate of origin, and HS Code 9031809090 declaration — everything your customs broker needs, prepared before the package leaves our dock.
• Tracking: AWB number sent to your email within 2 hours of dispatch. Real-time tracking link included.
• Bulk orders: For 5+ units, we can consolidate with other parts on your BOM and ship as a single consignment to reduce your customs clearance workload.

We have shipped to refineries in Saudi Arabia, power plants in Germany, compressor stations in Canada, and petrochemical facilities across Southeast Asia. The paperwork is clean, the packaging is industrial-grade, and the unit arrives ready to install.

Contact Information

📧 Email: [email protected]
📱 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.