Bently Nevada 330103-00-05-10-10-02-00 Proximity Transducer – 3300 XL Series

330103-00-05-10-10-02-00 — Gap-Voltage Transduction at the Core of Rotating Machinery Protection

The Bently Nevada 330103-00-05-10-10-02-00 is an 8 mm eddy-current proximity transducer engineered as the primary sensing node within the 3300 XL Proximity Transducer System. Its operational mandate is precise: convert the physical clearance between a non-contacting probe tip and a rotating conductive target into a calibrated DC voltage signal, delivering continuous, wear-free measurement of shaft radial vibration, axial displacement, and differential thermal expansion across the full machine operating envelope.

Within a turbomachinery protection architecture, the proximity transducer occupies the most mechanically exposed position in the measurement chain — mounted directly at the bearing housing, subject to oil mist, thermal cycling, and mechanical vibration. The 330103-00-05-10-10-02-00 addresses this environment through a stainless steel armored body, PEEK (polyether ether ketone) tip compound, and a hermetically sealed coil assembly. The probe itself contains no active electronics; all oscillator and demodulation circuitry resides in the remote Proximitor® driver, isolating signal-conditioning components from the harsh measurement-point environment.

The part number suffix encodes the system configuration: -05- designates a 5-metre matched extension cable, -10-10- specifies the armored cable and connector type, and -02-00 identifies the probe body thread and tip geometry. These parameters are not cosmetic — the distributed capacitance and inductance of the 5 m cable form an integral part of the Proximitor® oscillator tank circuit. Substituting a cable of any other length without recalibrating the driver will shift the scale factor away from the factory-certified 7.87 V/mm (200 mV/mil) value, invalidating the measurement chain’s API 670 compliance.

In protection systems governed by API 670 (5th Edition) and assessed under IEC 61511 SIL frameworks, the proximity transducer is the only sensor technology capable of delivering sub-millisecond gap-change response without mechanical contact. The 330103-00-05-10-10-02-00 satisfies this latency requirement through its passive inductive topology: the probe introduces no processing delay at the measurement point, and the Proximitor® output tracks gap changes at the full demodulation bandwidth of the oscillator circuit.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330103-00-05-10-10-02-00 operates on electromagnetic induction loss. The Proximitor® driver generates a high-frequency carrier — typically 500 kHz to 2 MHz depending on driver variant — transmitted through the matched coaxial cable to the wound coil inside the probe tip. As the probe approaches a conductive shaft surface, eddy currents induced in the target material generate a counter-magnetic field that loads the oscillator circuit, attenuating its amplitude. The Proximitor® demodulates this amplitude envelope into a DC output voltage linearly proportional to the air gap.

Single-Point Shield Grounding and EMC Architecture: The armored cable provides a continuous Faraday enclosure from probe body to Proximitor® input terminal. The shield conductor is grounded exclusively at the driver end. This topology prevents circulating ground-loop currents — a common source of 50/60 Hz interference in industrial environments with multiple earthing points — from coupling into the measurement signal. In installations adjacent to variable-frequency drives, large transformer banks, or high-current bus bars, this grounding architecture maintains signal-to-noise ratios sufficient for 1 µm resolution measurements without supplementary shielding conduit.

Thermal Coefficient and Axial Position Accuracy: The probe coil is wound on a thermally stable mandrel and encapsulated in a compound rated to +121 °C. The scale factor thermal coefficient of <±0.5% per 10 °C is critical for axial position channels: on a steam turbine with a 50 °C ambient swing across a startup cycle, this specification limits thermally induced position error to under 25 µm — well within the typical 125 µm alarm setpoint margin used in high-pressure turbine thrust bearing protection.

Impedance Matching and the 5 m Cable Constraint: The distributed capacitance (approximately 95 pF/m for the standard coaxial construction) and inductance of the extension cable are incorporated into the Proximitor® oscillator design at the factory. The 5 m cable length encoded in the -05- suffix is not interchangeable with 3 m or 9 m variants without recalibrating the driver’s trimmer network. Field substitution of a non-matched cable length is the most common cause of scale factor error in 3300 XL installations and will produce a systematic measurement offset that does not self-reveal during routine OK-relay checks.

PEEK Tip Chemistry and Chemical Resistance: PEEK maintains a flexural modulus above 3.5 GPa and chemical resistance to petroleum-based lubricants, phosphate-ester fire-resistant fluids, and steam condensate across the full probe operating temperature range. This material selection eliminates the tip swelling and dimensional creep observed in earlier epoxy-potted probe designs when exposed to turbine oil at elevated temperatures, preserving the probe-to-target gap geometry over multi-year service intervals.

System Integration Benefits

• Sub-millisecond measurement latency at the sensor node: The passive probe topology introduces zero processing delay at the measurement point. The Proximitor® output tracks gap changes at the full oscillator demodulation bandwidth, allowing the 3300 XL monitor to execute alarm and trip logic within a single scan cycle — typically 20 ms for a 16-channel rack — without any sensor-induced lag contribution to the overall protection system response time budget.
• Backward-compatible drop-in replacement for all 3300 XL rack variants: The 330103-00-05-10-10-02-00 is electrically and mechanically interchangeable with all 3300 XL rack generations (3300/16, /20, /25, /46, /55). No channel rescaling, software parameter modification, or rack reconfiguration is required when replacing a like-for-like probe in a running installation, minimizing planned outage duration.
• Hardware-level diagnostic transparency via OK relay: The Proximitor® driver’s OK relay de-energizes when the probe gap exits the linear range or when the cable circuit is open or shorted. This discrete output propagates to the monitor rack’s channel status register, enabling the DCS or safety PLC to distinguish a genuine process alarm from a sensor fault — a distinction mandatory under IEC 61511 SIL loop assessments and required for proof-test documentation.
• Zero mechanical wear at the measurement interface: The non-contacting eddy-current principle eliminates all wear mechanisms at the probe tip. Unlike piezoelectric accelerometers subject to crystal aging or velocity transducers with coil fatigue, the 330103 probe has no consumable element at the measurement point. Mean time between calibration checks in correctly installed 3300 XL systems exceeds 48 months in standard turbine service.
• Zone 1 / Division 1 hazardous-area deployment: Compatibility with the Bently Nevada 3300 XL Zener barrier enables installation in hydrogen-cooled generators and hydrocarbon compressor trains without requiring an intrinsically safe Proximitor® variant. The barrier limits probe-circuit energy below Group IIC ignition thresholds, broadening the application envelope without additional ATEX or NEC certification complexity.
• Dual-function channel assignment — radial vibration and axial position: A single 3300 XL rack accepts both radial vibration and axial position channel types from the same probe series. The 330103-00-05-10-10-02-00 can be assigned to either measurement function by monitor channel configuration, reducing spare-parts inventory to a single probe model for mixed-measurement racks and simplifying maintenance logistics.
• Direct API 670 compliance documentation: Facilities operating under insurance or regulatory mandates requiring API 670-compliant protection systems can reference the 330103-00-05-10-10-02-00 directly against the standard’s transducer performance tables without additional third-party testing. This eliminates a commissioning documentation step and accelerates plant acceptance testing sign-off.
• Wide thermal envelope covers arctic to high-pressure steam applications: The −35 °C lower operating limit accommodates LNG compressor installations in arctic climates; the +121 °C upper limit covers bearing housing locations on high-pressure steam turbines. A single probe model addresses the majority of rotating-machinery temperature envelopes, eliminating the need for application-specific probe variants in mixed-fleet maintenance programs.

Quality Assurance & Global Logistics

Each 330103-00-05-10-10-02-00 unit shipped from our Xiamen, China facility is a genuine Bently Nevada OEM component sourced through verified industrial supply channels. Incoming inspection includes physical label authentication against Bently Nevada reference standards, armored cable and connector integrity checks, and output linearity spot-verification against the published 7.87 V/mm scale factor where bench equipment permits. Units that do not pass inspection are quarantined and removed from available inventory — they are not offered for sale at any price.

Packaging follows anti-static and moisture-barrier protocols appropriate for precision inductive sensors: each probe is individually sealed in ESD-protective film, cushioned in closed-cell polyethylene foam, and shipped in a rigid export carton rated for international air freight drop and compression loads. Multi-unit orders include individual probe serialization on the packing list to support incoming inspection and asset-tagging procedures at the destination facility.

Shipping from Xiamen is available via DHL Express (2–4 business days to most destinations), FedEx International Priority, and sea freight LCL/FCL for bulk procurement. Export documentation — commercial invoice, packing list, and certificate of origin — is prepared accurately for every shipment. HS code classification and customs value declaration are handled to prevent clearance delays at destination ports. In-stock units ship within 1–3 business days of order confirmation. All units carry a 12-month warranty covering manufacturing defects from the date of shipment.

Contact Information

📧 Email: [email protected]
💬 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
📍 Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.