Bently Nevada 330103-00-14-05-02-CN Proximity Transducer – 3300 XL Series

330103-00-14-05-02-CN: 8 mm Eddy-Current Proximity Transducer System in Rotating Machinery Protection Loops

The Bently Nevada 330103-00-14-05-02-CN is a three-component, non-contacting displacement measurement system built around an 8 mm eddy-current probe, a 5-metre coaxial extension cable, and a compatible 3300 XL driver/proximitor. Within a machinery protection architecture, this assembly occupies the field-sensing tier: it converts the physical gap between probe tip and rotating shaft into a proportional DC voltage that feeds directly into monitor input cards for real-time vibration amplitude, phase, and axial position computation. The system is designed to API 670 Fifth Edition requirements and is the standard reference transducer for turbines, centrifugal compressors, boiler feed pumps, and gearboxes operating in critical or essential service classifications.

Unlike piezoelectric accelerometers, which measure acceleration and require double integration to derive displacement, the eddy-current proximity transducer delivers a direct, DC-coupled displacement signal from 0 Hz upward. This characteristic makes it indispensable for capturing slow-roll runout, static eccentricity, and sub-synchronous instability phenomena — failure modes that accelerometers cannot resolve at low shaft speeds. The 330103-00-14-05-02-CN system maintains a flat frequency response from DC to 10,000 Hz (–3 dB), covering the full spectrum of interest in most turbomachinery applications without additional signal conditioning.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330103-00-14-05-02-CN operates on the Lenz’s law induction principle. The driver/proximitor generates a high-frequency oscillator signal — typically in the 500 kHz to 2 MHz range depending on probe geometry — which is transmitted through the coaxial extension cable to the probe coil. When the probe tip approaches a conductive target, eddy currents are induced on the target surface, loading the oscillator circuit and reducing its amplitude. The driver’s demodulator stage converts this amplitude modulation into a proportional DC output voltage: gap increases produce more negative output, gap decreases produce less negative output, with a nominal –10 VDC at the calibrated center gap.

EMC Design: The coaxial cable architecture provides inherent electromagnetic shielding, with the outer conductor acting as a Faraday shield against radiated interference from variable-frequency drives, ignition systems, and high-current bus bars common in industrial environments. The driver circuitry incorporates differential input filtering and regulated oscillator bias to maintain scale factor stability within ±1% across the full supply voltage range (–20 to –26 VDC), preventing false alarms from power supply ripple.

Thermal Stability: The probe coil is wound on a ceramic former with a low thermal coefficient of expansion, limiting gap-equivalent thermal drift to less than 0.5 mil/°C across the operating range. This is critical in hot-section turbine bearing housings where ambient temperatures can cycle between cold-start and full-load conditions, a delta that would introduce significant measurement error in thermally unstable sensor designs.

Cable Impedance Matching: The 5-metre extension cable (suffix -05) is impedance-matched to the probe and driver to prevent reflections that would distort the high-frequency oscillator signal. The TNC connector (suffix -02) provides a secure, low-loss coaxial termination rated for continuous vibration environments, with a mating cycle life exceeding 500 operations — relevant for installations requiring periodic sensor replacement during planned outages.

Target Material Sensitivity: The 8 mm probe geometry and 3300 XL driver are factory-calibrated against AISI 4140 steel targets. For non-standard alloys (e.g., titanium impellers, Inconel shaft journals), the effective scale factor deviates due to differences in electrical conductivity and magnetic permeability. Bently Nevada publishes material correction factors; applying these at commissioning ensures measurement accuracy within the ±1% specification across the full linear range.

System Integration Benefits

• Direct API 670 compliance: The 330103-00-14-05-02-CN satisfies API 670 Fifth Edition transducer requirements without supplementary qualification testing, accelerating insurance approval and OEM acceptance for new installations and retrofits.
• Native compatibility with 3500 Series monitors: The 200 mV/mil scale factor and –24 VDC supply requirement match the input card specifications of Bently Nevada 3500/40M, 3500/42M, and 3500/45 monitor modules, eliminating re-ranging or signal conditioning hardware between field and rack.
• DC-coupled displacement output: The DC-to-10 kHz frequency response enables simultaneous measurement of static position (eccentricity, thrust position) and dynamic vibration within a single channel, reducing channel count and wiring complexity compared to accelerometer-based systems requiring separate DC position sensors.
• Deterministic signal latency: The analog output path from probe to monitor input introduces no digital processing delay, preserving the phase relationship between vibration signals on orthogonal measurement planes — essential for accurate orbit plot generation and rotor dynamic diagnostics.
• Diagnostic transparency via gap voltage monitoring: The –10 VDC nominal gap output provides a continuous, observable health indicator. Drift from nominal indicates probe fouling, target wear, or mounting looseness — detectable during routine surveillance without removing the sensor from service.
• IP67 environmental sealing: The probe and cable assembly withstands oil mist, steam condensate, and high-pressure wash-down, maintaining measurement integrity in wet-gas compressor casings and steam turbine bearing pedestals without additional protective enclosures.
• Sub-synchronous instability detection: The flat DC response captures oil-whirl and oil-whip phenomena at fractional multiples of running speed (typically 0.43–0.48×), failure modes that are invisible to high-pass-filtered accelerometer channels and represent a leading cause of catastrophic bearing failure in fluid-film bearing machines.
• Interchangeability within the 330103 family: The probe and driver are independently replaceable without recalibration of the monitor rack, provided the replacement components carry the same suffix codes. This modular serviceability reduces mean time to repair (MTTR) during unplanned outages, where minimizing downtime directly impacts production economics.

Quality Assurance & Global Logistics

Every 330103-00-14-05-02-CN unit dispatched from our Xiamen facility is sourced through verified supply channels with full traceability documentation. Incoming inspection covers visual examination of probe tip geometry, coaxial connector integrity, and cable jacket condition, followed by functional verification: oscillator frequency confirmation, scale factor measurement at two reference gaps, and output voltage linearity check across the full measurement range. Serial number and date-code records are cross-referenced against known counterfeit risk databases prior to release.

Units destined for critical-service applications are accompanied by a functional test report on request. Calibration certificates traceable to national standards are available for applications requiring documented measurement uncertainty budgets.

Logistics from Xiamen, China to global destinations are handled via DHL Express, FedEx International Priority, and UPS Worldwide Expedited, with typical transit times of 3–5 business days to Europe and North America. Full export documentation — commercial invoice, packing list, certificate of origin, and MSDS where applicable — is prepared for each shipment. For critical plant shutdowns, same-day dispatch and next-flight-out freight options are available upon direct request. All shipments are insured at declared value and tracked end-to-end with proactive status updates provided to the buyer.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.