Bently Nevada 330171-00-10-10-02-05 Proximity Probe – 3300 XL Series

Bently Nevada 330171-00-10-10-02-05 — 8 mm Eddy Current Proximity Probe in the 3300 XL Transducer System

The 330171-00-10-10-02-05 is an 8 mm eddy current proximity probe manufactured by Bently Nevada (a Baker Hughes company) as a core sensing element within the 3300 XL Proximity Transducer System. It operates on the principle of electromagnetic induction: a high-frequency oscillator (typically 1.0 MHz) drives a coil wound at the probe tip, generating an alternating magnetic field. When a conductive target — typically AISI 4140 steel — enters this field, eddy currents are induced on the target surface, loading the oscillator circuit and producing a voltage shift proportional to the gap distance. The driver/oscillator-demodulator (330180 Series) converts this impedance change into a DC voltage output at a nominal sensitivity of 200 mV/mil (7.87 V/mm), providing a continuous, non-contact measurement of radial shaft displacement or axial position with sub-micron resolution.

In a rotating machinery protection loop, this probe occupies the first node in the signal chain: mechanical motion → electromagnetic coupling → conditioned DC voltage → monitoring rack input. Its accuracy at this node directly determines the fidelity of every downstream alarm, trip, and trend record. The 10 mm probe body length and integral 10 ft (≈3 m) coaxial cable are factory-matched to the 330180 driver, ensuring the system operates within its calibrated linear range of 0–80 mil (0–2.03 mm) without field recalibration.

📩 Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330171-00-10-10-02-05 integrates several hardware-level design decisions that distinguish it from generic eddy current sensors in industrial markets.

Coil Geometry and Field Uniformity. The 8 mm tip diameter is not arbitrary — it defines the effective sensing field diameter, which governs the probe’s sensitivity to target surface irregularities (runout, scratches, material inhomogeneity). Bently Nevada’s coil winding geometry is optimized to produce a near-uniform field across the linear range, minimizing the sensitivity variation that would otherwise appear as measurement noise at the monitoring rack. The coil is encapsulated in a thermally stable polymer compound that maintains dimensional integrity across the full −35°C to +177°C operating envelope, preventing coil shift that would alter the calibrated sensitivity constant.

Matched-System Calibration Architecture. The -00-10-10-02-05 suffix encodes the probe’s calibration set: it is factory-characterized as a matched assembly with a specific 330130 extension cable length and 330180 driver. The total system impedance — probe coil + cable capacitance + driver input impedance — is trimmed at the factory to achieve the 200 mV/mil sensitivity within ±1% tolerance. Substituting any element without recalibration introduces a systematic offset that cannot be corrected by monitoring rack scaling alone.

EMC Design and Shielding. The integral coaxial cable provides continuous 360° electrostatic shielding from probe tip to driver input, suppressing capacitively coupled interference from adjacent high-voltage cables, VFD switching noise, and RF sources common in turbomachinery environments. The shield is grounded at the driver end only (single-point grounding), eliminating ground loop currents that would appear as low-frequency noise on the displacement signal. This architecture allows the probe to maintain signal integrity in environments with conducted EMI levels consistent with IEC 61000-4-6 Class A.

Thermal Compensation. Eddy current sensitivity is a function of target conductivity, which varies with temperature. The 330171 series incorporates passive thermal compensation in the driver circuit (330180) that corrects for the conductivity-temperature coefficient of AISI 4140 steel across the rated temperature range, maintaining sensitivity within the API 670 accuracy band without active temperature measurement or software correction.

Mechanical Mounting Integrity. The probe body is machined to accept standard 3/8-24 UNF or M10×1 mounting threads (configuration-dependent), with a locknut provision to prevent vibration-induced loosening. The tip-to-body transition is designed to minimize stress concentration under the cyclic mechanical loads present in high-vibration turbomachinery installations, where probe mounting bosses can experience acceleration levels exceeding 50 g.

System Integration Benefits

• Deterministic signal latency: The analog output of the 330171 probe reaches the 3500 rack input with a propagation delay governed only by cable length (≈5 ns/m), ensuring that shaft displacement events are captured within the monitoring system’s scan cycle without digital processing latency.
• Direct API 670 compliance: The probe meets API 670 5th Edition requirements for radial vibration, axial position, and differential expansion measurements, eliminating the need for third-party compliance verification in new machinery protection system designs.
• Non-contact measurement eliminates wear: With no physical contact between probe and shaft, there is zero mechanical wear on the sensing element, and no periodic replacement interval driven by contact fatigue — only environmental degradation limits service life.
• High-resolution displacement data: At 200 mV/mil sensitivity and a typical monitoring rack input resolution of 0.1 mV, the effective displacement resolution is 0.5 µm — sufficient to detect early-stage bearing wear, rotor bow, and seal rub before they progress to trip-level events.
• Seamless integration with System 1 software: The analog output maps directly to System 1 dynamic data channels, enabling waveform capture, orbit plot generation, and spectral analysis without signal conditioning adapters or scaling corrections.
• Broad target material compatibility with recalibration: While factory-calibrated for AISI 4140 steel, the probe can be recalibrated for stainless steel, titanium, or aluminum targets using Bently Nevada’s documented recalibration procedure, extending applicability to non-standard rotor materials.
• Redundant installation support: The 8 mm tip diameter allows dual-probe installation at 90° separation in standard bearing housings without mechanical interference, supporting the redundant XY vibration measurement configuration required by API 670 for critical machinery.
• Diagnostic transparency via gap voltage monitoring: The DC gap voltage output (nominally −10 VDC at mid-range) provides a continuous, independently readable signal that maintenance personnel can verify with a standard voltmeter, enabling field confirmation of probe installation gap without specialized test equipment.

Quality Assurance & Global Logistics

Every 330171-00-10-10-02-05 unit supplied through siemensplc.com is sourced as genuine Bently Nevada (Baker Hughes) OEM hardware. Our procurement process requires full supply chain traceability: each unit is accompanied by sourcing documentation that records the distribution channel, lot identification, and date of manufacture where available. Physical inspection covers connector pin integrity, cable jacket condition, probe tip surface finish, and label authenticity against current Bently Nevada packaging standards.

Units are stored in a climate-controlled warehouse in Xiamen, China, in anti-static, moisture-barrier packaging consistent with IEC 60068-2-30 damp heat storage requirements. For international shipments, we use DHL Express, FedEx International Priority, and UPS Worldwide Expedited as primary carriers, with typical transit times of 3–7 business days to Europe, North America, Southeast Asia, and the Middle East. Export documentation — including commercial invoice, packing list, and certificate of origin — is prepared in compliance with destination country import requirements. For orders requiring a certificate of conformance or material test report, these are provided at no additional charge upon request.

All units carry a 12-month warranty from the date of shipment, covering manufacturing defects and factory calibration integrity. Warranty claims are processed with a target response time of 48 hours from receipt of the defective unit.

Contact Information

📧 Email: [email protected]
📱 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
📍 Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.