GE IC695ACC400-AA CPU Energy Pack Module

GE IC695ACC400-AA — Stop the Clock on Your Downtime. Ship Today from Xiamen.

Every minute your PACSystems RX3i CPU sits unprotected after an energy pack failure is money bleeding out of your operation. A single uncontrolled shutdown on a pharmaceutical batch line or an automotive weld cell can cost tens of thousands before the shift ends. The IC695ACC400-AA is the factory-specified capacitor-based energy pack for the RX3i CPU — and we have it on the shelf, tested, boxed, and ready to move via DHL or FedEx within hours of your order confirmation.

No waiting on distributor lead times. No chasing allocation queues. You call it, we ship it.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

Fault Code Reference — What the CPU Is Telling You

When the IC695ACC400-AA degrades or fails, the RX3i CPU logs a hardware fault in the I/O Fault Table. In Proficy Machine Edition, navigate to Target → Diagnostics → I/O Fault Table and look for fault type 0x0083 or a CPU hardware fault referencing the energy pack attachment. If the CPU is generating repeated “Power Loss Detected” events without an actual supply interruption, a failing capacitor pack is the first thing to swap — not the power supply.

Step-by-Step Replacement Procedure

1. Place the CPU in STOP mode via the keyswitch or PME before touching anything. Do not attempt hot-swap — GE explicitly prohibits it in GFK-2741.
2. De-energize the rack. Shut down the RX3i power supply (IC695PSA040 or IC695PSD040). Verify with a multimeter at the backplane power connector — do not rely on indicator LEDs alone.
3. Discharge wait. Allow 30 seconds after power-down before handling the energy pack. The capacitors hold charge and can cause unexpected CPU behavior if removed immediately.
4. Slide and release. The IC695ACC400-AA clips onto the CPU faceplate with a friction latch. Press the release tab on the bottom edge and slide the module downward to disengage.
5. Inspect the CPU connector pins. Before seating the new unit, visually check the 6-pin interface on the CPU faceplate for bent pins or oxidation. A damaged connector here will cause the new energy pack to report a fault immediately.
6. Seat the replacement. Align the new IC695ACC400-AA with the CPU faceplate guide rails and press firmly upward until the latch clicks. There should be no gap between the module body and the CPU housing.
7. Power up and verify. Re-energize the rack. In PME, confirm the I/O Fault Table is clear of energy pack faults. The CPU OK LED should be solid green within 10 seconds of power-on.
8. Firmware check. If the CPU is running firmware below v7.0, the energy pack will not be recognized. Upgrade via PME’s firmware update utility before declaring the replacement successful.

Common Mistakes That Waste Your Time

• Replacing the power supply when the actual fault is the energy pack — the CPU fault log is specific, read it first.
• Ordering the IC695ACC400 (no suffix) when the CPU requires the -AA revision. The suffix matters for firmware handshake compatibility on CPE330 and CPE400 variants.
• Skipping the 30-second discharge wait and then wondering why the CPU throws a new fault on first power-up.
• Assuming the energy pack is the problem when the real issue is a loose CPU faceplate connector — always inspect the interface pins.

Reliability in Harsh Conditions

The IC695ACC400-AA is not a data-center component. It was engineered for the floor — the kind of floor where ambient temperature swings 30 degrees between morning startup and afternoon peak production, where VFD switching noise saturates the cabinet, and where the enclosure door gets slammed twice a shift.

The supercapacitor cell stack inside the module is rated across a −40°C to +85°C storage range and a 0°C to +60°C operating envelope — covering everything from a cold Canadian compressor station in January to a Southeast Asian foundry in August. Unlike lithium battery backup modules, there is no electrolyte degradation, no capacity fade from partial charge cycles, and no HSE concern about shipping lithium cells internationally.

Vibration resistance aligns with IEC 61131-2 mechanical requirements — the same standard that governs the RX3i backplane and CPU. The module’s direct-mount design eliminates the flex-cable failure mode that plagues external battery packs; there are no wires to chafe, no connectors to corrode, and no PCB-mounted battery holders to crack under thermal cycling.

In high-humidity environments — coastal petrochemical plants, paper mills, food processing facilities with washdown cycles — the conformal-coated PCB inside the energy pack provides a meaningful barrier against condensation-induced leakage paths. This is not a consumer-grade component with a marketing claim; it is a GE factory-specified module built to the same qualification standards as the CPU it protects.

Units sourced through siemensplc.com are inspected for label authenticity, revision marking, and physical condition before dispatch. Capacitor charge integrity is verified where bench testing is applicable. You are not receiving a gray-market pull from an unknown source — you are receiving a traceable unit with lot code documentation available on request.

Global Express Logistics

Our dispatch hub is in Xiamen, China — one of the most logistics-connected export cities on the mainland, with direct DHL and FedEx gateway access and daily cut-off times that support same-day booking for orders confirmed before 15:00 CST.

Standard Express Transit Times (from Xiamen dispatch):

• Southeast Asia (Singapore, Thailand, Malaysia, Vietnam) — 2 to 3 business days via DHL Express
• Middle East (UAE, Saudi Arabia, Qatar) — 3 to 4 business days via FedEx International Priority
• Europe (Germany, Netherlands, UK, Poland) — 3 to 5 business days via DHL Express Worldwide
• North America (USA, Canada, Mexico) — 4 to 6 business days via FedEx International Priority
• Australia & New Zealand — 3 to 5 business days via DHL Express
• South America (Brazil, Chile, Colombia) — 5 to 7 business days via FedEx or DHL

Every shipment includes a commercial invoice with accurate HS code declaration (HS 8537.10 for PLC modules), packing list, and country of origin certificate where required for customs clearance. For customers in regulated industries requiring an end-user declaration or import license support documentation, contact us before placing the order and we will prepare the paperwork in parallel with picking and packing.

Tracking numbers are issued within 2 hours of carrier pickup and sent directly to your registered email. For urgent shipments, WhatsApp notification with the AWB number is available on request — because when your line is down, you need to know exactly where your part is, not just that it “shipped.”

For volume orders of 3 or more units, we can arrange consolidated shipment with a single customs entry to reduce brokerage fees on your end. Contact us for a freight quote before checkout.

Contact Information

📧 Email: [email protected]
💬 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.