Parker CPX2570S/E2/E3/F8/S1 Servo Drive

CPX2570S/E2/E3/F8/S1 — Stop the Clock on Your Downtime. Drive Ships Today.

Your line is down. Every minute costs money — production loss, penalty clauses, idle labor. The Parker CPX2570S/E2/E3/F8/S1 Compax-S digital servo drive is the exact module you need, and we have it on the shelf in Xiamen right now. No lead-time negotiation with a distributor. No 8-week factory queue. We pull it, test it, pack it, and hand it to DHL before your shift ends.

This is not a generic listing. The CPX2570S/E2/E3/F8/S1 is a specific Parker Compax-S platform that supports four feedback types — incremental encoder (E2), resolver (E3), HIPERFACE (F8), and SinCos (S1) — within a single hardware unit. If your nameplate reads exactly this part number, you are in the right place.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

After ten years of field work, here are the failure patterns I see most often with the Compax-S platform and what to watch for when you swap this drive:

Common Fault Codes & Root Causes

• F01 / Overcurrent: Usually a shorted motor winding or a damaged power stage IGBT. Before fitting the replacement, megger-test the motor at 500 V DC. If insulation resistance is below 1 MΩ, the motor is the culprit — a new drive will fault immediately on the same motor.
• F07 / DC Bus Overvoltage: Braking resistor open-circuit or undersized. Measure the resistor before powering up the replacement. A 25 A Compax-S typically needs a braking resistor in the 50–100 Ω / 200 W range depending on deceleration duty cycle.
• F14 / Feedback Error: Check the feedback cable shield continuity and connector pins before blaming the drive. A corroded D-sub pin on the encoder connector causes intermittent F14 faults that look like drive failures. Clean the connector, re-crimp if needed.
• F22 / Following Error: After replacement, the velocity and position loop gains stored in the old drive are gone. You must reload the parameter file from your backup or re-tune. If no backup exists, start with the Parker default parameter set for your motor type and tune from there.

Replacement Procedure — Key Steps

• Power down and lock out the cabinet. Wait at least 5 minutes for the DC bus capacitors to discharge below 50 V (measure with a meter — do not assume).
• Note the DIP switch positions on the old drive before removal. The Compax-S uses DIP switches for axis address assignment in multi-axis configurations. Replicate the exact switch pattern on the new unit.
• The CPX2570S/E2/E3/F8/S1 stores its parameter set in internal non-volatile memory. The replacement unit ships with factory defaults. You must upload your saved parameter file via Parker ServoManager software before enabling the drive. If you do not have a backup, contact us — we can supply the default parameter template for common motor pairings.
• After parameter upload, perform a phasing check (auto-phase or manual) before running the axis under load. Skipping this step on a resolver-feedback (E3) system will result in runaway or oscillation.
• Verify firmware version compatibility with your motion controller. Compax-S firmware is not automatically backward-compatible across major revisions. Match the firmware version to what was running on the failed unit.

Reliability in Harsh Conditions

The Compax-S platform was designed for industrial environments where office-grade electronics would fail within weeks. The CPX2570S/E2/E3/F8/S1 is built to withstand the realities of a production floor:

Vibration: The drive meets IEC 60068-2-6 sinusoidal vibration testing — 10–57 Hz at 0.075 mm displacement, 57–150 Hz at 1 g. In practice, this means it survives being mounted on a machine frame that transmits cutting forces or press impacts without PCB solder joint fatigue. Use anti-vibration mounts if your cabinet is directly bolted to a press bed.

Thermal Cycling: Rated for 0–45 °C ambient with internal thermal management. The drive’s power stage uses thermally bonded IGBT modules with integrated NTC sensors. If ambient temperature in your cabinet exceeds 40 °C, ensure the cooling fan on the drive heatsink is operational — a blocked fan is the single most common cause of premature thermal shutdown in summer production peaks.

Humidity & Contamination: IP20 rating means the drive is not sealed against dust or moisture ingress. In foundry, food processing, or coastal environments, fit the cabinet with positive-pressure filtered air or use conformal-coated PCB variants where available. Condensation from thermal cycling is a known failure mode — ensure the cabinet heater is functional during cold startups.

EMC: The Compax-S is CE-marked and includes internal EMC filtering. For installations near large VFDs or welding equipment, use shielded motor cables with 360° shield termination at both ends. A floating shield is worse than no shield in high-interference environments.

Global Express Logistics

We ship from our Xiamen warehouse, which gives us direct access to Xiamen Gaoqi International Airport — one of the highest-throughput cargo hubs in Southeast China. Here is exactly how your order moves:

• Order confirmed before 14:00 CST: Same-day dispatch. The drive is pulled from stock, function-tested, packed in anti-static foam with humidity indicator card, and handed to DHL Express or FedEx International Priority the same afternoon.
• DHL Express transit times: Europe 2–3 business days. North America 3–4 business days. Southeast Asia 1–2 business days. Middle East 3–4 business days. Australia 3–5 business days.
• Documentation: Commercial invoice, packing list, and certificate of conformity ship with every order. For EU imports, we provide the HS code (8537.10) and country of origin declaration. For US imports, we provide the HTS code and can arrange a formal entry if value exceeds the de minimis threshold.
• Tracking: A DHL or FedEx tracking number is emailed within 2 hours of dispatch. We monitor the shipment and proactively notify you of any customs holds.
• Emergency freight: For absolute critical situations, we can arrange same-day courier pickup with overnight delivery to major hubs in Europe and North America. Contact us directly on WhatsApp for this option — it is not listed at checkout.

We have shipped to automotive plants in Germany, semiconductor fabs in Taiwan, food processing facilities in the UK, and oil & gas installations in the Middle East. Customs clearance experience across these jurisdictions means your drive does not sit in a bonded warehouse waiting for paperwork.

Contact Information

Line down? Do not wait. Reach us now:

• Email: [email protected]
• WhatsApp: +86 18359268345
• Web: siemensplc.com

© 2026 siemensplc.com. All rights reserved.