Siemens A5E00399482 C98043-A1716-L26 Drive Power Module

Siemens A5E00399482 C98043-A1716-L26 — Stop the Clock on Your Downtime

Every minute your SIMOREG DC drive sits dead, your line is bleeding money. The A5E00399482 (board reference C98043-A1716-L26) is the internal power module that feeds regulated DC rails to the control electronics of Siemens SIMOREG DC Master and related C98043-series drive platforms. When this board fails, the entire drive goes dark — no fault code, no output, no production. We stock this unit in Xiamen and ship globally within 24 hours of order confirmation. That is the only number that matters when your plant is down.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

After 10 years of field work on Siemens drive systems, here is what actually happens on site — and what you need to know before you swap this board.

Common failure signatures for A5E00399482:

• Drive powers up but immediately trips on F002 / F003 (DC link undervoltage): The power module is no longer delivering stable rails to the control board. The drive’s self-test detects the sag and shuts down before the main contactor even closes. Replace A5E00399482 first before chasing the DC bus.
• Blank operator panel (OP1S / PMU) with no fault code: If the panel is completely dead but the incoming AC supply is confirmed good, the internal 24 V and 5 V rails from this module have collapsed. This is not a panel fault — it is a power module fault.
• Intermittent drive restarts under load: Thermal stress on aging electrolytic capacitors inside the module causes rail droop under current demand. The drive resets itself as a protective response. You will see this worsen in summer or in poorly ventilated cabinets.
• F025 / A0503 alarms with no obvious cause: Noise on the internal supply rails can corrupt encoder feedback signals. Before replacing the encoder or cable, verify the power module output is clean.

Replacement procedure — field-tested steps:

1. Isolate the drive fully: open the main breaker, lock out, and verify zero voltage on the DC bus with a meter. The DC bus on SIMOREG units can hold charge for several minutes after power-off.
2. Photograph all connector positions on the existing A5E00399482 before disconnecting anything. The C98043 backplane has multiple ribbon and Molex connectors that are easy to transpose.
3. Note the L-revision suffix on the installed board (L26 in this case). The L-revision indicates a PCB revision level. L26 is a later revision than L1/L2/L4/L6 and includes circuit updates. Do not substitute an earlier L-revision without confirming compatibility with the drive’s firmware version.
4. Check the drive’s firmware version via the operator panel (P060 → r069 on SIMOREG DC Master). Firmware versions below 3.x may not fully support L26 hardware features. Contact us if you are running legacy firmware — we can advise on the correct board revision.
5. There are no DIP switches or address jumpers on this specific power module. It is a passive power supply board — no configuration is required after installation.
6. After fitting the new board, power up with the motor disconnected. Verify the operator panel illuminates and the drive reaches the ready state (r000 = 0) before reconnecting the load.
7. Run a short no-load test cycle and monitor DC bus voltage (P006) and control supply status parameters for the first 10 minutes of operation.

Reliability in Harsh Conditions

The A5E00399482 is engineered to Siemens’ industrial-grade specifications, which means it is built for environments that would destroy consumer-grade electronics within weeks. The PCB uses conformal coating on critical sections to resist condensation and airborne contaminants — a real concern in paper mills, chemical plants, and coastal facilities where humidity regularly exceeds 85% RH. The power components are rated for continuous operation at ambient temperatures up to 55°C inside the drive cabinet, with derating curves published in the SIMOREG hardware manual for higher temperatures.

Vibration resistance meets IEC 60068-2-6 test profiles, which covers the sinusoidal vibration loads typical of heavy machinery foundations, compressor rooms, and crane cabinets. The board’s through-hole construction on high-stress components — rather than purely SMD — gives it superior mechanical fatigue resistance over long service cycles. Units we supply are stored in climate-controlled conditions and shipped in foam-lined cartons with moisture-barrier bags to ensure they arrive in the same condition they left the factory.

Global Express Logistics

Our warehouse is located in Xiamen, Fujian Province — one of China’s primary export hubs with direct access to DHL, FedEx, and UPS international gateways. Here is how the shipment process works from the moment you confirm your order:

• Day 0 (Order Confirmation): Payment confirmed, unit pulled from stock, inspected, and packed. Export documentation prepared (commercial invoice, packing list, HS code 8538.90).
• Day 1 (Dispatch): Shipment handed to DHL Express or FedEx International Priority. Tracking number issued to you within 2 hours of pickup scan.
• Day 2–4 (Transit): Typical transit time to Europe is 3–4 business days; Southeast Asia 1–2 days; North America 3–5 days; Middle East 3–4 days. Express options available for next-day delivery to major hubs.
• Customs: We declare accurately and provide all documentation required for customs clearance. For EU imports, we can provide EUR.1 or origin certificates on request. Buyers are responsible for import duties in their country.
• Tracking: Full end-to-end tracking shared via email. WhatsApp updates available on request for urgent shipments.

If your plant is down and you need the fastest possible delivery, contact us directly before placing the order. We will confirm the fastest available routing and provide a delivery commitment before you commit to the purchase.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.