Schneider Electric BMXFCW301S PLC Cable – Modicon M340

Schneider Electric BMXFCW301S – 3-Metre Shielded Cord Set for Modicon M340 Signal Integrity in High-Noise Industrial Environments

The BMXFCW301S is a factory-assembled, fully shielded cord set engineered by Schneider Electric for the Modicon M340 (BMX-series) programmable automation controller platform. Its primary function within a control loop is to maintain deterministic, low-latency signal transmission between M340 communication or specialty I/O modules and field-side devices, while suppressing conducted and radiated electromagnetic interference that would otherwise corrupt process data or trigger spurious module faults. In distributed control architectures where variable-frequency drives, servo amplifiers, and high-current contactors share cabinet space with PLC backplanes, the quality of the interconnecting cable is not a peripheral concern — it is a direct determinant of scan-cycle consistency and diagnostic accuracy.

At 3 metres, the BMXFCW301S covers the most common intra-cabinet and short inter-cabinet routing distances without requiring field termination. The cable ships pre-terminated with connectors matched to the mechanical and electrical specification of the target BMX module port, eliminating the dimensional tolerance risk associated with field-assembled alternatives. Each unit undergoes continuity, insulation resistance, and shield-integrity verification at the factory before shipment.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The BMXFCW301S addresses two distinct interference pathways that affect M340 module performance: conducted EMI propagating along signal conductors from connected field devices, and radiated EMI coupling into the cable from adjacent power wiring or switching equipment.

The braided copper shield, bonded at both connector shells, creates a Faraday enclosure around the signal conductors. When the shield is grounded at a single point (typically the PLC cabinet PE rail), common-mode noise currents induced by external fields are diverted to ground rather than superimposed on the differential signal pair. This is particularly relevant for M340 analog I/O modules operating at 4–20 mA or ±10 V ranges, where a 50 mV noise spike represents a measurable percentage of full-scale input — sufficient to cause erroneous process variable readings and unnecessary PID output corrections.

For M340 serial communication modules (Modbus RTU, CANopen, Profibus DP), the shield continuity also reduces the characteristic impedance variation along the cable run. Impedance discontinuities generate signal reflections that degrade the eye diagram at the receiver, increasing the bit-error rate at higher baud rates. The factory-terminated connectors maintain controlled impedance transition at the cable-to-module interface, a parameter that field-crimped connectors rarely achieve consistently.

The PTFE inner insulation provides a stable dielectric constant across the operating temperature range, preventing capacitance drift that would alter the cable’s high-frequency attenuation profile as cabinet temperature cycles between cold-start and full-load thermal equilibrium. This thermal stability is particularly relevant in outdoor enclosures and foundry environments where ambient temperature swings exceed 40 °C within a single shift.

From an EMC design standpoint, the BMXFCW301S is classified as a Class A shielded interconnect under IEC 61000-4-3 (radiated immunity) and IEC 61000-4-6 (conducted immunity), consistent with the M340 platform’s declared immunity levels. Using an unshielded or inadequately shielded substitute cable can invalidate the system-level CE declaration of the machine or panel in which the M340 is installed.

System Integration Benefits

• Deterministic scan-cycle preservation: By eliminating noise-induced communication retries between the M340 CPU and connected modules, the cord set prevents the variable latency that retry mechanisms introduce into the PLC scan cycle, keeping cycle time within the declared deterministic window.
• Diagnostic transparency: Clean signal paths reduce the incidence of spurious module fault codes (e.g., communication timeout, CRC error), allowing maintenance teams to distinguish genuine hardware failures from noise-induced transients without ambiguity.
• Plug-and-play commissioning: Factory-terminated connectors eliminate field-assembly errors — incorrect pin assignment, insufficient crimp force, or missing shield termination — that account for a significant proportion of commissioning delays in M340 installations.
• Reduced cabinet re-work risk: Pre-tested cable assemblies arrive with documented continuity and insulation resistance values, providing a baseline for future preventive maintenance measurements without requiring initial field testing.
• Compliance with Schneider Electric system-level EMC declarations: Using OEM-specified cable accessories preserves the validity of the M340 platform’s CE marking and simplifies third-party machine safety audits.
• Thermal stability across operating range: PTFE dielectric and PVC outer jacket maintain electrical performance from −25 °C to +70 °C, covering the full M340 operating envelope without derating.
• Mechanical retention at module port: Factory-matched connector geometry ensures the specified insertion force and retention force are met, preventing intermittent disconnection in high-vibration environments such as press lines or compressor rooms.
• Inventory standardisation: A single BMXFCW301S SKU covers the majority of intra-cabinet M340 wiring distances, reducing the number of cable part numbers that maintenance stores must manage and reorder.

Quality Assurance & Global Logistics

Every BMXFCW301S unit supplied through siemensplc.com is sourced directly from authorised Schneider Electric distribution channels. Each unit carries the original Schneider Electric part label, batch traceability code, and factory test record. No repackaged, relabelled, or grey-market stock is accepted into our inventory. Upon request, we provide a certificate of conformity and, where available, the manufacturer’s test report for MRO procurement teams and quality auditors.

Our warehouse is located in Xiamen, China — a major international logistics hub with direct access to Xiamen Gaoqi International Airport and Xiamen Port. Standard in-stock orders are processed within 24 hours of payment confirmation. Shipping options include DHL Express (2–4 business days to most destinations), FedEx International Priority, and sea freight for bulk orders. Export documentation — commercial invoice, packing list, and certificate of origin — is prepared in compliance with the destination country’s import requirements. We have shipped M340 accessories to customers in Germany, the United States, Australia, Southeast Asia, and the Middle East, with a consistent on-time delivery rate.

All items are packed in anti-static bags and rigid outer cartons with foam inserts to prevent connector damage during transit. For orders requiring expedited customs clearance, we can provide HS code documentation and pre-shipment inspection reports upon request.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.