Bently Nevada 21000-16-10-00-102-03-02 Proximity Probe Housing Assembly

21000-16-10-00-102-03-02 Proximity Probe Housing – Every Hour of Downtime Costs You More Than This Part

Your turbine is down. The DCS is throwing Probe Fault or Not OK alarms. Maintenance is standing by. The clock is running at $10,000–$50,000 per hour in lost production. You need the Bently Nevada 21000-16-10-00-102-03-02 in your hands — not in three weeks.

We stock this housing assembly in Xiamen and ship globally via DHL Express and FedEx International Priority. Most orders clear customs and arrive on-site within 3–5 business days. No broker delays. No minimum order quantity. One unit or ten — same urgency, same service.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

After ten years of field work on turbomachinery protection systems, here are the failure modes I see most often with 21000-series housing assemblies — and what to check before you condemn the part:

1. “Not OK” LED on 3500/40M or 3500/42M — Is it really the housing?
Before pulling the housing, verify the proximitor output voltage. A healthy 3300 XL proximitor should read between −10 VDC and −18 VDC at nominal gap. If you’re reading −24 VDC (open circuit) or 0 VDC (short), the fault is in the probe-cable-proximitor loop — not necessarily the housing. Swap the probe tip first; it’s the cheapest component in the chain.

2. Gap Setting After Housing Replacement
This is where most field teams lose time. The 21000-series housing geometry requires the probe tip to be set at 1.0 mm ± 0.05 mm from the shaft surface for standard 8 mm probes (verify against your specific Bently Nevada installation drawing). Use a feeler gauge — do not rely on the thread count method alone. After gap setting, confirm proximitor output is within the linear range before re-energizing the monitor channel.

3. Suffix Code Mismatch — The Silent Killer
The part number suffix -16-10-00-102-03-02 encodes thread size, probe length, temperature rating, cable length, and connector type. Installing a housing with a mismatched cable length suffix (-101 vs -102) will shift the proximitor’s operating point and generate false vibration readings — sometimes within alarm thresholds, making the fault invisible until the next calibration cycle. Always verify the full part number before installation.

4. Common Fault Codes on 3500 System

• OK Relay De-energized + Channel Fault LED: Check probe continuity and proximitor supply voltage (−24 VDC nominal). A failed housing with internal cable damage will present identically to a broken extension cable.
• High Vibration Alert / Danger with No Process Change: Suspect mechanical looseness in the housing threads or probe tip contamination (oil coke, scale). Remove, clean, re-gap, and re-torque to spec.
• Intermittent OK Status: Thermal cycling fault — common in housings exposed to steam leaks. The stainless body expands and contracts, causing micro-movement at the probe thread interface. Replace the housing and apply anti-seize compound to threads during reinstallation.
• Asymmetric Orbit Plot: If the orbit on your System 1 or Orbit software shows a non-circular pattern on a machine known to run cleanly, check for probe housing misalignment. The housing centerline must be perpendicular to the shaft surface within 1°.

5. Firmware / Configuration Notes
The 21000-series housing itself carries no firmware — it is a passive mechanical assembly. However, after replacement, verify the 3500 monitor channel configuration: transducer type, full-scale range, and OK limit setpoints. If the replacement probe has a different sensitivity (V/mm) than the original, the monitor channel must be reconfigured accordingly. This is a common oversight that generates nuisance alarms post-maintenance.

Reliability in Harsh Conditions

The 21000-16-10-00-102-03-02 is not a commercial-grade sensor. It is built to survive the environments that destroy ordinary instrumentation:

Vibration: The stainless steel housing body and precision-machined thread form maintain probe alignment under continuous broadband vibration. In compressor trains running at 10,000–20,000 RPM, the housing sees constant mechanical excitation. The 21000-series design eliminates the resonance modes that cause probe tip migration in lesser housings.

Temperature: Turbine bearing pedestals routinely reach 80–120°C ambient. Steam leaks can spike local temperatures higher. The 316 SS construction and high-temperature cable specification in the -102 suffix ensure the assembly maintains dimensional stability and electrical integrity across the full operating range.

Moisture and Process Contamination: Oil mist, condensate, and process gas ingress are constant threats in compressor and turbine environments. The housing’s sealed construction and corrosion-resistant material selection prevent the galvanic corrosion and thread galling that sideline inferior assemblies within months of installation.

Continuous Duty: API 670 machinery protection systems run 24/7/365 with no scheduled downtime. The 21000-series housing is rated for continuous operation in this duty cycle. There are no wear surfaces, no consumable elements, and no scheduled maintenance intervals for the housing assembly itself — only the probe tip requires periodic inspection.

Global Express Logistics

Our Xiamen warehouse is positioned for fast export to every major industrial hub. Here is exactly how your order moves:

Day 0 — Order Confirmation: Payment confirmed before 14:00 CST triggers same-day picking, inspection, and export documentation preparation. ESD-safe packaging, commercial invoice, and packing list are generated automatically.

Day 1 — Export Clearance: Shipment is handed to DHL Express or FedEx International Priority with pre-lodged customs data. HS Code 9026.80 (instruments for measuring flow, level, pressure) is declared. No broker delays — we handle export compliance in-house.

Day 2–3 — In Transit: Real-time tracking number provided via email. DHL and FedEx both operate direct flights from Xiamen Gaoqi International Airport to major hubs: Frankfurt, Dubai, Singapore, Los Angeles, and Houston. Typical transit time to Europe and the Middle East is 2–3 days; North America 3–4 days; Southeast Asia 1–2 days.

Day 3–5 — Delivery: Door-to-door delivery to your plant, warehouse, or freight forwarder. Import duties and taxes are the buyer’s responsibility; we provide all documentation required for customs clearance including country of origin certificate on request.

For shipments to sanctioned or restricted destinations, please contact us before ordering. We comply fully with Chinese export regulations and international trade controls.

Contact Information

📧 Email: [email protected]
📱 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.