Bently Nevada 330101-00-10-10-02-CN Proximity Probe – 3300 XL Series

Bently Nevada 330101-00-10-10-02-CN: Eddy-Current Proximity Probe for Turbomachinery Shaft Monitoring

The Bently Nevada 330101-00-10-10-02-CN is an 8 mm eddy-current proximity probe belonging to the 3300 XL Proximity Transducer System — a platform that has defined the measurement standard for radial shaft vibration and axial position monitoring in critical rotating machinery for over three decades. This specific configuration carries a 1.0 m integral cable terminated with a CN-type connector, a thread body of M10 × 1, and a calibrated linear range of 0.25 mm to 2.26 mm (10 mil to 90 mil) against AISI 4140 steel targets at a nominal scale factor of 7.87 V/mm (200 mV/mil).

In a machinery protection architecture, the proximity probe is the primary sensing element. It converts the physical gap between its tip and the rotating shaft surface into a proportional DC voltage signal. That signal travels through the 330130 extension cable to the 330180 Proximitor® sensor, which provides the oscillator-demodulator circuitry and conditions the output for the 3500 Series monitor rack. The 330101-00-10-10-02-CN occupies the first and most critical position in this signal chain: any degradation in probe linearity, tip geometry, or cable integrity propagates directly into the monitor’s alarm and trip logic. Selecting a dimensionally and electrically correct replacement is therefore not a procurement decision — it is a machinery safety decision.

The probe body is machined from 316 stainless steel with a hermetically sealed sensing tip. The integral cable is rated to +177 °C, allowing installation in bearing housings and pedestal environments where ambient temperatures routinely exceed 120 °C. The CN connector provides a positive-locking, vibration-resistant termination that maintains contact integrity under the mechanical excitation levels present in turbine and compressor pedestals.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330101-00-10-10-02-CN operates on the principle of Faraday induction: the Proximitor sensor drives a high-frequency oscillating current (typically 1.0 MHz) through the probe coil, generating an electromagnetic field that extends axially from the tip. When a conductive target enters this field, eddy currents are induced on the target surface, loading the coil and reducing oscillation amplitude. The Proximitor’s demodulator circuit converts this amplitude change into a linear DC voltage proportional to gap distance.

Several hardware design decisions in the 3300 XL platform directly affect measurement integrity in harsh industrial environments:

• Coil encapsulation geometry: The 8 mm tip diameter is selected to balance field penetration depth against lateral sensitivity. A smaller tip concentrates the field but reduces the usable linear range; the 8 mm format achieves the 2.01 mm linear span required by API 670 for radial vibration channels on shafts up to approximately 100 mm diameter.
• Cable impedance matching: The integral cable and extension cable form a matched transmission line. The 330130 extension cable is specified to maintain the total system cable length within the Proximitor’s compensation range. Substituting non-OEM cables with differing capacitance per unit length shifts the oscillator operating point and introduces scale factor error — a failure mode that does not trigger a fault indication but corrupts the measurement silently.
• EMC shielding architecture: The integral cable uses a double-braid shield construction with drain wire, providing attenuation of radiated interference from variable-frequency drives, bus bars, and high-current switching equipment commonly co-located with rotating machinery. The CN connector’s metal shell provides 360° shield termination continuity, preventing shield discontinuity at the junction — a common source of common-mode noise injection in field installations.
• Thermal compensation: The Proximitor sensor contains temperature-compensating circuitry that corrects for the probe coil’s temperature coefficient of resistance. However, the probe itself must remain within its rated −35 °C to +177 °C envelope for this compensation to remain valid. Installations where the probe body is exposed to temperatures above this limit — such as direct contact with steam lines — require thermal isolation standoffs.
• Target surface requirements: The standard calibration assumes a flat, smooth AISI 4140 target with surface finish Ra ≤ 1.6 µm. Shaft surface irregularities — including runout, scratches, and residual magnetism — appear as once-per-revolution or broadband noise in the vibration signal. API 670 specifies maximum allowable electrical and mechanical runout limits that must be verified during commissioning.

System Integration Benefits

• API 670 compliance out of the box: The 330101-00-10-10-02-CN meets the dimensional, electrical, and performance requirements of API 670 Fifth Edition without additional calibration, enabling direct use in new installations and certified replacements in existing machinery protection systems.
• Deterministic signal latency: The eddy-current measurement chain introduces no mechanical hysteresis or contact bounce. Signal propagation from shaft displacement to monitor input is governed solely by the Proximitor’s demodulator bandwidth (typically DC to 10 kHz), ensuring that transient events such as rub initiation or blade-pass excitation are captured without temporal smearing.
• Backward compatibility with 3300 Series monitors: The probe is electrically compatible with legacy Bently Nevada 3300 Series monitor cards, protecting existing infrastructure investments while allowing incremental system upgrades.
• Diagnostic transparency via gap voltage monitoring: The DC component of the Proximitor output provides a continuous indication of probe-to-shaft gap. Operators can trend this value over time to detect shaft centerline migration, bearing wear, and thermal growth — diagnostic information that is available without any additional instrumentation.
• Reduced installation variability: The M10 × 1 thread and defined probe body length standardize mounting geometry across machine types. Combined with the fixed integral cable length, this eliminates field-cut cable joints — a common source of impedance discontinuity and moisture ingress.
• Dual-channel redundancy support: Two probes mounted at 90° (X-Y configuration) per bearing provide the orbital data required for full shaft centerline analysis. The 330101-00-10-10-02-CN’s consistent scale factor across units ensures that X and Y channel gains are matched without individual trimming.
• Compatibility with Bently Nevada System 1 software: When connected through the 3500 rack, measurement data is accessible to Bently Nevada System 1 condition monitoring software for trend analysis, alarm management, and machinery diagnostics — without any signal conditioning adapters.
• Long-term parts availability: The 3300 XL platform has maintained dimensional and electrical compatibility across production generations. Replacement probes sourced today are interchangeable with units installed in the 1990s, eliminating the need for system recalibration on a like-for-like swap.

Quality Assurance & Global Logistics

Every unit supplied by siemensplc.com is sourced through verified industrial distribution channels with full traceability to the original manufacturer. Prior to dispatch, each probe undergoes visual inspection of the tip encapsulation, connector shell, and cable jacket for physical integrity. Part number labeling is cross-checked against the order specification to prevent mis-shipment of similar-format probes with differing cable lengths or connector types.

Original manufacturer documentation — including the calibration data sheet and certificate of conformance — is available upon request and provided with the shipment where available from the supply chain. Anti-static, foam-lined packaging protects the precision tip geometry and cable assembly during international transit.

Shipments originate from our warehouse in Xiamen, China, with access to DHL Express, FedEx International Priority, and sea freight consolidation services. Standard air express transit times to major industrial hubs: Southeast Asia 2–3 business days, Europe 3–5 business days, North America 4–6 business days, Middle East 3–4 business days. Full export documentation — commercial invoice, packing list, and certificate of origin — is prepared for each shipment to facilitate customs clearance in destination countries. All units carry a 12-month warranty against manufacturing defects from the date of shipment.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.