Bently Nevada 330101-00-12-10-02-CN Proximity Transducer – 3300 XL Series

330101-00-12-10-02-CN: Eddy-Current Proximity Transducer for Critical Rotating Machinery Monitoring

The Bently Nevada 330101-00-12-10-02-CN is an 8 mm eddy-current proximity transducer belonging to the 3300 XL Series — a platform engineered specifically for continuous, non-contact measurement of shaft radial vibration, axial position, and differential expansion in turbomachinery and other critical rotating assets. The CN suffix designates compliance with Chinese national hazardous-area certification requirements (ATEX/IECEx), making this variant the correct selection for installations subject to GB 3836 and equivalent domestic regulatory frameworks.

Unlike general-purpose inductive sensors, the 3300 XL transducer system operates as a matched three-component assembly: probe, extension cable, and driver/oscillator-demodulator. The 330101-00-12-10-02-CN probe is factory-calibrated as part of this system, with a nominal sensitivity of 7.87 V/mm (200 mV/mil) traceable to the specific driver it is paired with. Substituting unmatched components degrades linearity and introduces gain error across the measurement range — a detail frequently overlooked in field replacements.

The probe tip diameter of 8 mm defines the electromagnetic field geometry and, consequently, the usable linear measurement range of 0.25 mm to 2.54 mm (10 to 100 mil). Within this window, the output voltage is linear to within ±0.05 mm, providing the resolution required by API 670 machinery protection standards. The frequency response extends from DC to 10,000 Hz, covering both slow-roll runout characterization at startup and high-frequency sub-synchronous instability events in compressor trains.

Operating temperature at the probe tip spans −35 °C to +177 °C, accommodating bearing housing environments in steam turbines where ambient temperatures routinely exceed 150 °C. The integral cable construction — 1.2 m in this configuration — eliminates the connector junction at the probe body, which is statistically the highest-failure-probability point in field-assembled transducer systems. The extension cable (1.0 m, system-matched) carries the signal to the driver mounted outside the hazardous zone, maintaining coaxial impedance continuity throughout.

Supply voltage is −24 VDC nominal, consistent with the 3300 XL driver family. The output swings from −1 VDC (probe at minimum gap) to −17 VDC (probe at maximum gap), providing a 16 V span that is directly compatible with Bently Nevada 3500 Series monitor input cards without signal conditioning. This direct compatibility is a key integration advantage when retrofitting existing 3500/40M or 3500/42M radial vibration monitor slots.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330101-00-12-10-02-CN operates on the eddy-current (electromagnetic induction) principle. The probe tip houses a wound coil driven by a high-frequency oscillator (typically 1.0 MHz carrier) embedded in the matched driver module. When the conductive target shaft surface enters the electromagnetic field, eddy currents are induced, loading the coil and reducing its Q-factor. The driver demodulates this impedance change into a DC-proportional output voltage — a fundamentally passive measurement at the probe that requires no active electronics within the hazardous zone.

The CN-suffix variant incorporates a hermetically sealed probe body with a fluoropolymer-jacketed integral cable, providing resistance to hydrocarbon condensates, H₂S atmospheres, and steam ingress — conditions common in Chinese petrochemical and power generation installations. The coil assembly is encapsulated in a ceramic-filled epoxy compound with a thermal expansion coefficient matched to the titanium probe housing, preventing gap variation between the coil and tip face across the full operating temperature range. This thermal compensation is what sustains the ±0.05 mm linearity specification at 177 °C probe tip temperature.

EMC performance is achieved through the coaxial cable architecture: the outer shield of the integral cable serves as both the signal return conductor and the Faraday shield, attenuating radiated interference from variable-frequency drives, arc furnaces, and high-current bus bars — all common in the industrial environments where this transducer is deployed. The driver module provides additional common-mode rejection, with a CMRR typically exceeding 60 dB at 50/60 Hz, ensuring that ground potential differences between the machine frame and the control room do not corrupt the vibration signal.

The matched-system calibration approach — where probe, extension cable, and driver are characterized as a unit — eliminates the gain uncertainty introduced by cable capacitance variation. A 1.0 m extension cable adds approximately 100 pF of distributed capacitance; the factory calibration absorbs this into the sensitivity coefficient, so the 7.87 V/mm figure is valid for the complete assembly, not just the probe in isolation.

System Integration Benefits

• Direct API 670 Compliance: The 0.25–2.54 mm linear range and ≤±0.05 mm linearity error satisfy API 670 Fifth Edition transducer performance requirements without additional field calibration, reducing commissioning time on new machinery protection systems.
• Zero-Wear Measurement Architecture: Non-contact eddy-current sensing imposes no mechanical load on the shaft and has no moving parts at the measurement point, eliminating sensor-induced wear and the associated maintenance intervals required by contact-type displacement sensors.
• DC-to-10 kHz Bandwidth: The flat frequency response from DC enables simultaneous slow-roll runout capture during startup sequences and high-frequency sub-synchronous instability detection during full-speed operation — both within a single channel, without switching measurement modes.
• 3500 Series Monitor Compatibility: The −1 to −17 VDC output maps directly to Bently Nevada 3500/40M and 3500/42M radial vibration monitor input specifications, allowing drop-in replacement without reconfiguring monitor input scaling or alarm setpoints.
• Hazardous Zone Passive Probe: All active electronics reside in the driver module, which is mounted outside the classified area. The probe itself contains only passive coil elements, simplifying ATEX/IECEx zone documentation and reducing the scope of Ex-certified equipment requiring periodic inspection under IEC 60079-17.
• Integral Cable Reliability: Eliminating the probe-body connector junction removes the most common field failure mode in proximity transducer systems — connector corrosion and fretting under vibration — directly improving mean time between failures (MTBF) in high-vibration bearing housing environments.
• Thermal Stability to 177 °C: The ceramic-epoxy coil encapsulation and matched thermal expansion design maintain calibration accuracy at steam turbine bearing housing temperatures where standard proximity probes exhibit measurable sensitivity drift, avoiding false alarm conditions in machinery protection systems.
• Diagnostics Transparency: The linear DC output allows the monitoring system to distinguish between a genuine shaft displacement event and a transducer fault (open circuit, short, or driver failure) based on output voltage level — voltages outside the −1 to −17 VDC window indicate a system fault rather than a process condition, enabling deterministic fault isolation without physical inspection.

Quality Assurance & Global Logistics

Every 330101-00-12-10-02-CN unit dispatched from our Xiamen facility is sourced through verified supply channels with full part-number traceability to the Bently Nevada (Baker Hughes) manufacturing origin. Physical inspection covers label authenticity, connector and cable jacket integrity, housing dimensional conformance, and part-number cross-check against the original Bently Nevada datasheet. Where batch documentation is available — including manufacturer certificates of conformance (COC) and test records — these are provided with the shipment on request.

A 12-month warranty against manufacturing defects applies from the shipment date. Dead-on-arrival (DOA) units are replaced or credited within the standard return window. Returns are accepted within 30 days of receipt for unused units in original packaging.

Logistics from Xiamen, China are executed via DHL Express, FedEx International Priority, and UPS Worldwide Express, with typical in-stock dispatch within 1–3 business days. Export documentation — commercial invoice, packing list, certificate of origin, and HS Code 9031.80 classification — is prepared as standard. Customs support for import documentation is available on request for all served regions: Asia-Pacific, Middle East, Europe, the Americas, and Africa.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026