Bently Nevada 330103-00-24-05-02-00 Proximity Transducer

330103-00-24-05-02-00 — Stop the Clock on Your Downtime. Ship Today from Xiamen.

Your steam turbine tripped at 03:00. The DCS alarm log is screaming. Maintenance pulled the proximity transducer and confirmed it: the 330103-00-24-05-02-00 is dead — open circuit on the extension cable, or the probe tip is shorted from a shaft rub. Every hour this machine stays offline costs you real money. We stock this exact part number. We ship DHL Express from Xiamen. You get it back online.

The Bently Nevada 330103-00-24-05-02-00 is a precision eddy-current proximity transducer from the 3300 XL system — the global standard for API 670-compliant machinery protection on turbines, compressors, and pumps. This configuration carries a 24 mm probe tip, a 5-metre extension cable, and a 2-metre integral cable. It is factory-matched as a complete system: probe, extension, and proximitor must be calibrated together. Swapping only the probe without re-matching the proximitor is the single most common commissioning error in the field — and it will give you a scale factor error that looks like a real vibration event.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

Fault Scenario 1 — Probe Gap Alarm / OK Relay Drops Out
The 3500 rack throws a Not OK on the channel. First check: measure the DC bias voltage at the proximitor output with a calibrated DMM. Nominal is −18 VDC ±1 V at the correct air gap (typically 1.0–1.5 mm for a 24 mm probe). If you read 0 VDC or −24 VDC rail voltage, the probe is either shorted or open. Disconnect the extension cable at the proximitor junction box and measure resistance across the probe coil pins — should read 8–12 Ω. Open circuit = failed probe. Short to shield = shaft rub damage.

Fault Scenario 2 — High 1× Vibration Reading After Replacement
You installed a new 330103-00-24-05-02-00 but the 1× amplitude is 30% higher than before. Classic system mismatch. The 3300 XL system is calibrated as a matched set — probe + extension cable + proximitor. Each set has a unique calibration certificate. If you replaced only the probe and kept the old proximitor, the scale factor is off. Pull the proximitor label: the serial number must match the probe system serial. If not, you need the matched proximitor or a full system re-calibration using a Bently Nevada calibrator.

Fault Scenario 3 — Intermittent OK / Not OK Cycling
This is almost always a connector issue. The MIL-spec connectors on the extension cable are the weakest mechanical point in the system. In high-vibration environments, the locking ring backs off over time. Torque the connector to spec (finger-tight plus 1/4 turn with a strap wrench — never use pliers on the knurled ring). If the fault persists after re-torquing, flex the cable near the connector while monitoring the DC bias: a dropout during flexing confirms a broken conductor inside the cable jacket.

Replacement Procedure — Step by Step

1. Bypass the channel in the 3500 rack (inhibit the OK relay) before disconnecting the probe to prevent a spurious trip.
2. Record the existing air gap with a feeler gauge before removing the probe holder — this is your reinstallation reference.
3. Disconnect the extension cable at the junction box first, then unthread the probe from the holder. Never pull the cable to remove the probe.
4. Install the new 330103-00-24-05-02-00. Thread the probe in by hand until it contacts the shaft, then back out to the recorded air gap. Lock the jam nut.
5. Reconnect the extension cable. Verify the DC bias voltage at the proximitor output before removing the inhibit.
6. Perform a static calibration check: use a non-ferrous shim to simulate the target and verify the output tracks the expected scale factor (7.87 V/mm).
7. Remove the inhibit. Monitor the channel for 15 minutes at operating speed before returning the machine to normal protection mode.

Configuration Notes: The 330103-00-24-05-02-00 does not have DIP switches or firmware — it is a passive eddy-current device. All configuration is in the 3500 rack I/O module (e.g., 3500/42M). Verify the channel is set to Proximity input type, scale factor 200 mV/mil, and the gap voltage setpoints match your machinery OEM specification.

Reliability in Harsh Conditions

The 3300 XL probe tip is encapsulated in a high-temperature epoxy compound rated to 177 °C continuous — it survives the radiant heat of a steam turbine bearing housing without signal drift. The 24 mm probe body is machined from 316 stainless steel, providing corrosion resistance in wet gas and offshore environments where salt-laden air attacks lesser materials within months.

The extension cable uses a double-shielded, fluoropolymer-jacketed construction that resists hydrocarbon fluids, lubricating oil, and cleaning solvents. In petrochemical plants where cable trays run through areas regularly washed down with caustic solutions, this jacket integrity is not a marketing claim — it is the difference between a 10-year cable life and a 10-month replacement cycle.

Vibration resistance is validated to IEC 60068-2-6 profiles covering the frequency ranges generated by rotating machinery foundations. The probe-to-holder thread engagement, combined with the jam nut locking mechanism, prevents probe migration under continuous vibration — a failure mode that causes slow, insidious gap drift that looks like a real shaft movement event and triggers unnecessary shutdowns.

In high-humidity tropical environments — common in Southeast Asian petrochemical complexes and coastal power plants — the MIL-spec connectors are sealed with O-rings that maintain IP67 integrity when properly torqued. Moisture ingress at the connector is the leading cause of premature 3300 XL system failures in these climates. Inspect and re-torque connectors during every scheduled maintenance window.

Global Express Logistics

Our warehouse is located in Xiamen, Fujian Province — one of China’s primary industrial export hubs with direct access to Xiamen Gaoqi International Airport (XMN), a major DHL and FedEx gateway for time-critical industrial shipments.

Standard Express Routing: Orders confirmed before 14:00 CST are dispatched same day. DHL Express Economy reaches most of Southeast Asia in 2–3 business days, Europe in 3–5 days, and North America in 4–6 days. FedEx International Priority is available for destinations where DHL coverage is limited.

Documentation Package: Every shipment includes a commercial invoice with accurate HS code classification (HS 9031.80 for proximity transducers), packing list, certificate of origin, and — on request — a material safety data sheet and manufacturer’s certificate of conformance. For customers in the EU, we provide the necessary documentation for customs clearance under the current import duty framework.

Packaging: The 330103-00-24-05-02-00 is packed in anti-static foam-lined boxes with rigid outer cartons rated for international air freight handling. The probe tip is protected by a machined plastic cap. Extension cable connectors are individually bagged and sealed. We do not use loose packing peanuts — every component is immobilised to survive the handling chain from Xiamen to your site.

Tracking & Communication: You receive the AWB number within 2 hours of dispatch. Our team monitors shipments proactively — if a customs hold or routing delay occurs, we contact you before you need to chase us.

Contact Information

📧 Email: [email protected]
📱 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.