Bently Nevada 330104-00-04-10-01-CN Proximity Transducer – 3300 XL Series

Bently Nevada 330104-00-04-10-01-CN: Eddy-Current Proximity Transducer System for Critical Rotating Machinery Protection

The 330104-00-04-10-01-CN is a three-component eddy-current proximity transducer system within Bently Nevada’s 3300 XL Series — a platform that has established itself as the de facto standard for shaft dynamic measurement in API 670-governed machinery protection applications. This specific configuration combines a 1.0 m probe cable with a CN-type connector termination and a 2.5 m extension cable, forming a matched system calibrated to deliver a scale factor of 7.87 V/mm (200 mV/mil) against AISI 4140 steel targets.

Unlike general-purpose displacement sensors, the 3300 XL architecture is purpose-built for continuous, unattended operation in environments where ambient temperature, electromagnetic interference, and mechanical vibration would degrade the performance of conventional sensing technologies. The probe tip diameter of 8 mm defines the electromagnetic field geometry, which in turn governs the linear measurement range of 2.0 mm (80 mil) — a range selected to cover the full shaft displacement envelope encountered in most centrifugal compressor and steam turbine bearing housings.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330104-00-04-10-01-CN operates on the principle of high-frequency electromagnetic field perturbation. The probe coil, driven by the paired 330180-series oscillator-demodulator at a carrier frequency in the range of 500 kHz to 2 MHz, generates a focused field at the probe tip. When a conductive target enters this field, eddy currents are induced on the target surface, absorbing energy from the coil circuit and reducing its effective impedance. The driver continuously measures this impedance change and outputs a DC-coupled voltage linearly proportional to the probe-to-target gap — the fundamental measurement signal.

EMC Design Architecture: The coaxial cable assembly between probe and driver is a critical EMC element. The outer shield provides a continuous Faraday enclosure from probe body to driver housing, attenuating radiated interference from adjacent high-voltage switchgear, variable frequency drives (VFDs), and motor starters — all common in turbomachinery environments. The driver’s internal signal conditioning employs synchronous demodulation referenced to the carrier oscillator, which provides inherent rejection of out-of-band noise. This architecture maintains measurement integrity even in environments with conducted EMI levels that would saturate conventional analog sensors.

Thermal Compensation: The probe coil winding uses a temperature-stable alloy with a controlled thermal coefficient of resistance. The driver’s demodulation circuit incorporates a temperature-tracking reference that compensates for the probe coil’s residual thermal drift, maintaining scale factor accuracy within ±0.5% across the full –35°C to +177°C probe operating range. This is particularly significant in steam turbine applications where bearing housing temperatures can vary by 80°C between cold startup and full-load steady state.

CN Connector Termination Logic: The CN connector designation specifies a standardized field-termination interface between the probe cable and extension cable. This connector type uses a positive-locking bayonet mechanism with gold-plated contacts, minimizing contact resistance variation — a critical factor because any resistance change in the signal path alters the effective cable impedance seen by the driver, which directly shifts the output voltage baseline. The CN termination maintains contact resistance below 5 mΩ across the rated temperature range, preserving system-level calibration without field recalibration after connector mating.

Three-Component System Integrity: The probe, extension cable, and driver are calibrated as a matched set. Substituting any single component from a different calibration batch introduces a scale factor error that is not self-evident during normal operation — the monitor will display plausible but inaccurate gap values. This is why the full part number string (probe + extension + driver) must be preserved when ordering replacement systems for existing API 670 installations.

System Integration Benefits

• Drop-in API 670 Compliance: The 330104-00-04-10-01-CN meets API 670 5th Edition requirements for radial vibration and axial position measurement without additional hardware modification to the monitor rack, reducing engineering review time during replacement projects.
• Deterministic DC-Coupled Output: The –1 VDC to –21 VDC output is a true DC-coupled signal, meaning the monitor receives instantaneous gap information with zero phase lag at frequencies from 0 Hz upward. This is essential for slow-roll runout compensation and static position monitoring, which AC-coupled sensors cannot perform.
• 10 kHz Bandwidth for Sub-Synchronous Detection: The flat frequency response to 10,000 Hz captures sub-synchronous instabilities (oil whirl, oil whip) and super-synchronous harmonics that precede bearing failure by hours or days, enabling condition-based maintenance decisions before damage propagates.
• System 1 Software Integration: The analog output interfaces directly with Bently Nevada System 1 condition monitoring software, enabling real-time spectrum analysis, orbit plot generation, Bode plots, and historian trending without signal conversion hardware.
• Hazardous Area Deployment: ATEX and FM certifications allow installation in Zone 1 / Division 1 classified areas — eliminating the need for intrinsic safety barriers in many configurations and reducing panel wiring complexity.
• Zero Mechanical Wear: Non-contact measurement eliminates the sensor degradation mechanisms (spring fatigue, contact oxidation, diaphragm creep) that limit the service life of contact-type displacement sensors. Mean time between replacement in continuous service typically exceeds 10 years.
• Diagnostic Transparency via Gap Voltage: The raw output voltage provides a direct, unambiguous indication of probe-to-shaft gap. Maintenance technicians can verify probe installation gap (typically 1.0 mm nominal, –10.5 VDC) with a standard voltmeter without specialized test equipment, reducing commissioning time.
• Backward Compatibility with 3300 Monitor Infrastructure: Existing 3300 XL monitor cards, relay modules, and I/O wiring require no modification when replacing a 330104-series probe, protecting the capital investment in installed monitor infrastructure.

Quality Assurance & Global Logistics

Every unit of the 330104-00-04-10-01-CN supplied by siemensplc.com is sourced through verified channels with full traceability to Bently Nevada’s authorized distribution network. Incoming inspection covers connector integrity, cable sheath continuity, label serialization verification, and where test equipment permits, output voltage linearity validation against a reference gap fixture. Units that do not pass inspection are quarantined and not offered for sale.

Documentation available on request includes Certificate of Conformance (CoC), packing list, commercial invoice with HS code declaration, and country of origin certification — all required for customs clearance in most jurisdictions. Export compliance is handled in accordance with Chinese customs regulations at Xiamen port, with accurate HS code classification to prevent clearance delays at the destination.

Payment is accepted in USD, EUR, HKD, and CNY via T/T bank transfer, with proforma invoice issued prior to shipment. For qualified institutional buyers, net-term arrangements are available upon credit review.

Shipping is executed via DHL Express, FedEx International Priority, or customer-nominated freight forwarder. In-stock units are dispatched within 3–5 business days of payment clearance. Full tracking information and commercial shipping documents are provided at time of dispatch. Insurance coverage is available for high-value shipments upon request.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.