Bently Nevada 330104-00-13-05-01-00 Proximity Transducer

330104-00-13-05-01-00 — Stop the Clock on Your Downtime. Ship Today.

Every hour a turbine or compressor sits idle costs real money — production losses, penalty clauses, idle crews. The Bently Nevada 330104-00-13-05-01-00 is a precision 8mm eddy-current proximity transducer system built for the 3300 XL platform, and we keep it on the shelf in Xiamen specifically so your plant doesn’t have to wait weeks for an OEM lead time. One call, one shipment, back online.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

After ten years of crawling around turbine decks and compressor trains, here’s what actually goes wrong with the 330104 system — and what to check before you condemn the probe.

Fault 1 — Proximitor output reads -24V (rail low) or open circuit: Nine times out of ten this is a broken probe tip or a cracked armored cable at the compression fitting entry point. Before ordering a replacement, disconnect the probe at the junction box and measure resistance between the center conductor and shield. Anything above 5Ω on a 1m cable indicates a cable fault, not a proximitor failure. Replace the probe first.

Fault 2 — High DC gap voltage but erratic AC vibration signal: The extension cable connector is the usual culprit. Moisture ingress at the MIL-spec connector causes intermittent contact resistance. Clean with contact cleaner, re-torque to spec, and re-check. If the problem persists, swap the extension cable (330130-045-00-00) before condemning the proximitor.

Fault 3 — Scale factor drift, vibration readings 10–15% high or low: This happens when a non-OEM probe is paired with an OEM proximitor, or vice versa. The 3300 XL system is a matched set — probe, extension cable, and proximitor must all carry the same calibration lot. Never mix 3300 (non-XL) components with 3300 XL hardware; the scale factors differ and the system will pass self-test but read incorrectly.

Replacement procedure checklist:

• De-energize the proximitor supply rail (-24 VDC) before disconnecting any connector.
• Record the existing gap voltage (DC output) before removal — this is your baseline for setting the new probe gap.
• Thread the new probe to the same gap depth. Target gap voltage should be within ±0.5 VDC of the original reading at the same shaft position.
• Verify the new probe serial number and calibration date are logged in your machinery history file.
• Perform a slow-roll check (shaft turning at <600 RPM) to confirm runout is within API 670 limits before returning to service.
• If the unit feeds a 3500 rack, confirm the I/O module channel configuration matches the new probe’s scale factor — no firmware change is required for like-for-like 3300 XL replacements.

Non-standard target materials: If your shaft is Inconel, titanium, or duplex stainless, the standard 200 mV/mil calibration does not apply. A target material correction factor must be applied in the monitoring system, or a custom-calibrated probe ordered. Contact us with your shaft material spec before ordering.

Reliability in Harsh Conditions

The 330104-00-13-05-01-00 was not designed for a clean lab — it was designed for the places where failures are expensive and access is difficult. The armored probe cable withstands continuous mechanical flexing and resists hydrocarbon fluids, steam condensate, and cleaning solvents encountered in turbine enclosures. The MIL-C-5015 connector system maintains IP67 integrity even after repeated field disconnections, which matters when your maintenance crew is working in the rain on a platform shutdown.

Vibration immunity is built into the proximitor housing design. The electronics are potted and the internal components are secured against the 2g continuous vibration environments common on compressor skids. We have seen these units survive years of service on reciprocating compressor frames where lesser sensors fail within months. The probe tip itself is stainless-jacketed with a ceramic-filled sensing face — no moving parts, no wear mechanism, no scheduled replacement interval under normal operating conditions.

Thermal cycling is handled by the wide operating range: -35°C to +121°C at the probe tip covers everything from Arctic cold-start conditions to the hot-end environments of gas turbine exhaust casings. The proximitor electronics are rated to +66°C ambient, which is sufficient for most junction box installations when adequate ventilation is maintained. For higher ambient installations, consider remote mounting with extended cable.

Global Express Logistics

Our warehouse is located in Xiamen, Fujian Province — one of China’s primary export hubs with direct access to international freight lanes via Xiamen Gaoqi International Airport and Xiamen Port. This geography is deliberate: it gives us same-day handoff to DHL Express and FedEx International Priority for most destinations.

Standard dispatch timeline: Orders confirmed before 14:00 CST ship the same business day. Orders confirmed after 14:00 CST ship the following morning. Export documentation — commercial invoice, packing list, and certificate of origin — is prepared in parallel with packing and transmitted electronically to the carrier before physical handoff.

Typical transit times from Xiamen:

• Southeast Asia (Singapore, Thailand, Malaysia): 2–3 business days via DHL Express
• Middle East (UAE, Saudi Arabia, Qatar): 3–4 business days via FedEx International Priority
• Europe (Germany, Netherlands, UK): 3–5 business days via DHL Express Worldwide
• North America (USA, Canada): 4–5 business days via FedEx International Priority
• Australia / New Zealand: 3–4 business days via DHL Express

For plant shutdowns with hard restart deadlines, contact us directly on WhatsApp. We can arrange Saturday dispatch, split shipments, or pre-position stock at a freight forwarder of your choice. We have handled emergency shipments to offshore platforms, remote mining sites, and island power stations — logistics complexity is not a barrier.

All shipments are fully insured and tracked end-to-end. Tracking numbers are provided within 2 hours of dispatch. For high-value orders, we provide a photo of the packed unit with serial number visible before sealing the carton.

Contact Information

📧 Email: [email protected]
📱 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com

© 2026 siemensplc.com. All rights reserved.