Bently Nevada 330104-00-25-10-02-CN Proximity Transducer – 3300 XL Series

Bently Nevada 330104-00-25-10-02-CN: 8mm Eddy-Current Proximity Transducer in Rotating Machinery Protection Loops

The Bently Nevada 330104-00-25-10-02-CN is a field-proven, non-contact displacement measurement device belonging to the 3300 XL 8mm Proximity Transducer System family. Within a machinery protection control loop, this transducer occupies the sensing layer between the rotating shaft and the signal conditioning electronics — converting mechanical displacement into a calibrated DC voltage that downstream monitors and DCS platforms interpret as radial vibration, axial position, or eccentricity data. Its role is deterministic: any deviation in shaft orbit, thrust position, or runout is captured in real time, enabling the protection system to execute trip logic before mechanical damage propagates.

The -CN suffix designates the Chinese-market connector variant, engineered to interface directly with domestic cable ecosystems and terminal block standards prevalent in Chinese petrochemical, power generation, and heavy industrial installations. This eliminates field-side adapter assemblies that introduce impedance discontinuities and potential signal degradation in high-frequency vibration channels.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330104-00-25-10-02-CN operates on the eddy-current induction principle: a high-frequency oscillator within the Proximitor® sensor drives an alternating magnetic field through the probe coil. When a conductive target (shaft surface) enters the field, eddy currents are induced, loading the oscillator circuit and producing a proportional change in oscillator amplitude. The Proximitor® demodulates this amplitude-modulated signal into a DC voltage output with a linear transfer function of 200 mV/mil across the calibrated gap range.

EMC Design Architecture: The 3300 XL probe coil is wound on a ferrite core with a shielded housing that attenuates external electromagnetic interference. The coaxial extension cable maintains a controlled characteristic impedance, preventing reflections that would corrupt the high-frequency carrier signal. The cable shield is grounded at the Proximitor® end only — a single-point grounding topology that eliminates ground loop currents, a common source of 50/60 Hz noise injection in industrial environments with multiple earthing points.

Thermal Stability: The probe’s coil resistance and ferrite permeability exhibit temperature coefficients that are compensated by the Proximitor® sensor’s internal calibration circuitry. Over the full operating range of −35°C to +121°C, scale factor deviation is maintained within ±1% of nominal — a critical requirement for axial position channels where a 1 mil error at the transducer translates directly to a 200 mV error at the monitor input, potentially masking a genuine thrust bearing wear condition.

Impedance Matching and Cable Length Constraints: The −25 suffix specifies a 25 ft extension cable, which is the maximum recommended length for maintaining the oscillator loop gain within the Proximitor®’s compensation range. Exceeding this length increases distributed cable capacitance, shifts the resonant frequency of the LC tank circuit, and degrades linearity at the upper end of the frequency response. The factory-matched cable-probe-Proximitor® set eliminates the need for field calibration when installed as a complete system.

Redundancy Considerations: In API 670-compliant installations, two or three proximity transducers are typically deployed per measurement plane in a voting architecture (2oo3 or 1oo2). The 330104-00-25-10-02-CN’s consistent scale factor and output impedance characteristics ensure that the differential signal between redundant channels remains within the monitor’s OK status window under normal shaft orbit conditions, preventing spurious trips from transducer mismatch.

System Integration Benefits

• Direct compatibility with Bently Nevada 3500 Series monitors (3500/40M, 3500/42M, 3500/45, 3500/46M) — no signal conditioning adapters required; the Proximitor® output connects directly to the monitor’s input terminals at the specified −18 VDC nominal bias.
• Deterministic frequency response to 10,000 Hz enables capture of sub-synchronous instabilities (oil whirl at 0.43–0.48×), synchronous 1× imbalance, and super-synchronous blade-pass frequencies in a single measurement channel without anti-aliasing filter adjustments.
• Factory-calibrated scale factor eliminates field recalibration on initial installation, reducing commissioning time on multi-machine trains where dozens of transducer channels must be verified before first start.
• CN connector variant reduces field adaptation cost in Chinese installations by matching domestic cable termination standards, eliminating the impedance discontinuity and mechanical stress points introduced by field-fabricated adapter assemblies.
• API 670 compliance satisfies mandatory machinery protection requirements for gas turbines, steam turbines, centrifugal compressors, and large pumps in oil & gas, petrochemical, and power generation facilities — a prerequisite for insurance and regulatory approval in most jurisdictions.
• Analog output compatibility with any DCS or PLC platform — the Proximitor®’s ±10 V or 4–20 mA output interfaces to Siemens S7/PCS 7, ABB 800xA, Honeywell Experion, Emerson DeltaV, and Yokogawa CENTUM without signal conversion hardware.
• Diagnostic transparency via System 1® software — when integrated with Bently Nevada’s System 1® Evolution platform, the transducer channel provides not only vibration amplitude but also gap voltage, OK status, and historical trend data accessible to condition monitoring engineers without interrupting the protection function.
• Hazardous area deployment capability — compatible with Bently Nevada IS barriers for Zone 0/1 (ATEX) and Division 1 (NEC) installations, allowing the same transducer model to be deployed in both safe-area and classified-area machinery without maintaining separate spare part inventories.
• Long-term spare parts availability — the 3300 XL platform has maintained backward compatibility across multiple hardware revisions, protecting the capital investment in installed wiring infrastructure when transducers require replacement during scheduled maintenance outages.

Quality Assurance & Global Logistics

Every 330104-00-25-10-02-CN unit supplied by siemensplc.com is sourced as genuine Bently Nevada (Baker Hughes) hardware. Pre-shipment verification includes visual inspection of probe tip geometry and housing markings, serial number cross-reference against manufacturer records, and electrical parameter testing — oscillator frequency, output voltage at reference gap, and scale factor linearity — to confirm the unit performs within factory specification before it leaves our facility.

Units are dispatched from our warehouse in Xiamen, China, with access to major international freight lanes via Xiamen Gaoqi International Airport and Xiamen Port. Standard export documentation — commercial invoice, packing list, certificate of conformance, and country of origin certificate — is prepared for each shipment. For time-critical plant shutdowns, air freight with DHL Express or FedEx International Priority delivers to most industrial hubs in Europe, Southeast Asia, the Middle East, and North America within 3–5 business days from order confirmation. Sea freight consolidation is available for bulk orders requiring cost optimization over lead time.

All units are packed in ESD-safe foam-lined cartons with desiccant packs to protect the probe coil and cable assembly from humidity during transit. A 12-month warranty against manufacturing defects is provided from the date of shipment, covering electrical parameter drift beyond factory tolerance and mechanical defects in the probe housing or connector assembly.

Contact Information

📧 Email: [email protected]
📱 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
📍 Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.