Bently Nevada 330104-01-11-50-02-05 Proximity Probe

330104-01-11-50-02-05 — Stop the Clock on Your Downtime. Ship Today.

Your turbine is down. The DCS alarm is screaming. The shift supervisor is standing behind you. You already know the 3300 XL proximity probe is the culprit — you’ve seen this failure mode before. Every hour this machine stays offline costs real money: lost throughput, emergency labor, and the kind of pressure that makes a 3 AM phone call feel routine.

The Bently Nevada 330104-01-11-50-02-05 is in stock at our Xiamen warehouse. We don’t need 4 weeks. We don’t need a purchase order committee. We need your shipping address and a DHL account number — and this probe is on a plane tonight.

This is the 8mm eddy-current proximity probe with an 11-meter metric armored extension cable, factory-calibrated for the Bently Nevada 3300 XL Proximitor system. It measures shaft radial vibration and DC gap position with micron-level resolution — the exact sensing element your API 670 machinery protection loop depends on. No substitutes. No workarounds. The right part, shipped fast.

⚡ URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

Most common failure modes for the 330104-01-11-50-02-05:

1. Gap voltage out of range (typical alarm: -10V to -18V window violated)
This is the #1 field call. After installing the replacement probe, set your initial gap to the midpoint of the linear range — typically 1.0 mm to 1.5 mm from the shaft surface, targeting approximately -10.4 VDC at the Proximitor output. Use a calibrated gap tool or feeler gauge. Do not eyeball it. A gap that’s 0.3 mm off will push you outside the linear range and trigger a false danger alarm within hours of restart.

2. Cable jacket damage causing intermittent signal
The 11-meter armored cable is the most vulnerable part of this assembly in high-vibration installations. Inspect the full cable run before condemning the probe tip. A nick in the jacket near a conduit fitting will cause erratic gap voltage readings that look exactly like a bearing fault. Megger the cable shield continuity before pulling the probe.

3. Proximitor sensitivity mismatch after probe swap
The 330104 series is calibrated as a system — probe + extension cable + Proximitor. If you’re replacing only the probe and reusing an existing 330180 Proximitor, verify the Proximitor’s sensitivity setting (typically 200 mV/mil or 7.87 V/mm for 8mm probes). A mismatched sensitivity factor will cause the monitor to report incorrect vibration amplitude. Check the Proximitor label and cross-reference against the monitor’s channel configuration.

4. Thread galling on M10 × 1 probe holder
Metric probe holders in older installations often have corroded or galled threads. Never force the new probe in. Chase the threads with an M10 × 1 tap before installation. Torque to 14–17 N·m (10–12 ft·lb) with thread-locking compound. Over-torquing cracks the probe body — a mistake that costs you another probe and another shutdown.

5. Monitor channel not recognizing new probe (Bently Nevada 3300 XL)
After replacement, if the monitor channel shows a NOT OK status with the probe physically installed and gapped correctly, check: (a) the Proximitor power supply voltage at the monitor terminal — should be -24 VDC ±10%; (b) the interconnect cable continuity between Proximitor and monitor; (c) whether the monitor channel is configured for the correct transducer type (8mm, not 5mm). A channel configured for a 5mm probe will reject the 8mm calibration curve entirely.

Replacement checklist (field-tested sequence):

1. De-energize the Proximitor supply at the monitor rack — do not just disconnect the probe with power on (induces a spike that can latch the channel into fault).
2. Remove the old probe assembly. Inspect the probe holder bore for debris and corrosion.
3. Install the new 330104-01-11-50-02-05. Set initial gap to 1.0–1.5 mm. Torque to spec.
4. Route the 11-meter cable with minimum bend radius of 50 mm. Secure every 300 mm in high-vibration zones.
5. Re-energize Proximitor. Verify gap voltage at Proximitor output: target -10.4 VDC ±0.5V.
6. Confirm monitor channel status: OK, with vibration reading at or near zero (machine at rest).
7. Perform a slow-roll check before full-speed restart to confirm signal integrity.

Reliability in Harsh Conditions

The 3300 XL 8mm proximity probe was engineered for environments that destroy lesser sensors. The probe body is constructed from 316 stainless steel with a PEEK (polyether ether ketone) tip — chemically resistant to the hydrocarbon condensates, lube oil mist, and process gas atmospheres found in compressor trains and turbine bearing housings. The armored extension cable uses a stainless steel braid over a fluoropolymer-jacketed coaxial core, providing mechanical protection against abrasion and crush loads in cable trays while maintaining signal integrity at operating temperatures up to 121°C (250°F) continuous.

Vibration immunity is not an afterthought on this design. The probe-to-holder interface is threaded and locknut-secured, not friction-fit — it will not back out under the 50g shock loads common in reciprocating compressor installations. The coaxial connector at the probe body is a precision-machined, gold-contact design that maintains contact resistance below 0.1 Ω across the full temperature range, eliminating the connector-induced noise that plagues cheaper alternatives.

In offshore and coastal installations, the stainless steel construction resists salt fog corrosion per IEC 60068-2-52. Units destined for tropical climates or high-humidity enclosures have been deployed successfully in Southeast Asian petrochemical facilities operating at 95% RH without signal degradation. This is not marketing language — it is the reason plant engineers in Malaysia, Saudi Arabia, and Brazil specify Bently Nevada 3300 XL by name when writing their machinery protection specifications.

Global Express Logistics

Our Xiamen warehouse operates on a same-day dispatch model for in-stock items. Here is exactly what happens after you confirm your order:

Hour 0–2: Order confirmation and export documentation preparation. Commercial invoice, packing list, and HS code declaration (HS 9031.80 — instruments for measuring or checking) are generated immediately. For customers requiring a Certificate of Origin or Form E (ASEAN-China FTA), we prepare these in parallel.

Hour 2–4: Physical pick, inspection, and packaging. The 330104-01-11-50-02-05 is packed in a rigid anti-static foam insert inside a double-wall corrugated carton. The probe tip is protected with a machined plastic cap. The cable is coiled to a minimum 150 mm diameter and secured — not folded, not kinked.

Hour 4–6: DHL Express or FedEx International Priority pickup. Tracking number issued to you within 30 minutes of carrier collection.

Transit times from Xiamen:

• Southeast Asia (Singapore, Malaysia, Thailand, Indonesia): 1–2 business days
• Middle East (UAE, Saudi Arabia, Qatar, Kuwait): 2–3 business days
• Europe (Germany, Netherlands, UK, France): 3–4 business days
• North America (USA, Canada): 3–5 business days
• South America (Brazil, Chile, Colombia): 4–6 business days
• Africa (South Africa, Nigeria, Egypt): 4–7 business days

For customers with active DHL or FedEx accounts, we can ship on your account number to maximize your negotiated rates. For customers without carrier accounts, we invoice shipping at cost — no markup. Customs clearance support, including HS code documentation and commercial invoice formatting for your country’s import requirements, is included at no additional charge.

If your plant requires a specific carrier, a specific service level (e.g., DHL Express 9:00 AM delivery), or consolidated shipment with other parts on the same order, contact us before placing the order and we will accommodate it.

Contact Information

📧 Email: [email protected]
💬 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.