Bently Nevada 330104-11-22-10-02-CN Proximity Transducer

330104-11-22-10-02-CN Down? Every Minute of Shaft Vibration Unmonitored Is a Turbine at Risk

Your protection loop just went blind. The Bently Nevada 330104-11-22-10-02-CN proximity transducer is out — and without it, your 3500 rack is running on a bypass interlock, your operations team is watching a flatline channel, and your maintenance window is burning cash at whatever your plant’s hourly downtime rate is. We stock this part. It ships today from Xiamen. That’s the short version.

The longer version: the 3300 XL 8mm eddy-current proximity transducer system is a complete, calibrated assembly — probe, extension cable, and driver — matched and factory-set to a 7.87 V/mm scale factor. It is not interchangeable with 5mm or 11mm variants without recalibrating your monitor. The “11” in the part number is the probe cable length in inches; the “22” is the extension cable in feet. If your existing installation uses a different cable configuration, you need the exact suffix match. We carry the full 330104 matrix — contact us if you need a different suffix.

⚡ URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

Most common failure modes on the 330104-11-22-10-02-CN:

1. OK LED off, channel in fault — check the driver first, not the probe. The 3300 XL driver is the most thermally stressed component in the loop. If the probe cable is intact and the extension cable shows no visible damage, swap the driver before pulling the probe from the bearing housing. A failed driver reads as an open circuit on the 3500/42M — you’ll see a “Not OK” status with the gap voltage pegged at −24V or 0V.

2. Gap voltage out of range at installation. The 330104-11-22-10-02-CN is calibrated for a nominal gap of 1.0 mm (−10.2 VDC at gap). If you’re reading outside −7V to −13V at your target gap, check: (a) shaft material — non-4140 steel requires a correction factor; (b) probe tip contamination — oil film or metallic debris shifts the gap reading; (c) extension cable connector seating — the coaxial connectors are torque-sensitive, 1.1 N·m max.

3. High 1X vibration spike after replacement — not a bad part. If you see a sudden 1X amplitude jump after installing a new transducer, the probe is likely not seated at the same angular orientation as the original. The eddy-current field is not perfectly omnidirectional at the 8mm tip. Re-index the probe to the original clock position and re-gap.

4. 3500/42M channel showing “Danger” immediately after power-up. This is almost always a gap voltage issue, not a vibration event. The monitor checks gap voltage before enabling the vibration channel. Verify gap is within the linear range (0.25–2.25 mm) before assuming a machinery fault.

Replacement procedure checklist:

• Confirm bypass interlock is active on the 3500 rack before disconnecting the old transducer
• Record the original probe clock position and gap measurement before removal
• Inspect the probe tip for impact damage — a dented tip changes the calibration curve
• Torque the extension cable connectors to 1.1 N·m — finger-tight is not sufficient in a vibrating environment
• Set gap to 1.0 mm nominal, verify output is −10.2 VDC ±0.5V before releasing bypass
• Confirm the 3500/42M OK LED is solid green before returning the machine to service
• Log the replacement in your CMMS with the new part serial number for traceability

Reliability in Harsh Conditions

The 3300 XL platform was not designed for a clean instrument room. It was designed for the bearing housing of a 40 MW gas turbine running at 3,600 RPM in a tropical offshore environment. The 330104-11-22-10-02-CN probe is rated to +177°C continuous — that covers the bearing housing temperatures on most steam and gas turbines without derating. The extension cable uses a fluoropolymer jacket that resists hydrocarbon exposure, steam, and the cleaning solvents your maintenance crew will inevitably spray near it.

Vibration resistance is not a marketing claim on this part — it is a design requirement. The coaxial cable assembly is strain-relieved at both the probe body and the extension cable junction. Field failures from cable fatigue are rare on properly installed 3300 XL systems; when they do occur, they are almost always at the connector, not mid-cable. Inspect connectors at every planned outage.

The ATEX and FM certifications mean this transducer can be installed in Zone 1 / Division 1 hazardous areas with appropriate Zener barriers or galvanic isolators in the signal loop. The driver must be located in a safe area or in a certified enclosure — it is not rated for direct hazardous area installation.

Global Express Logistics

Stock is held at our Xiamen warehouse, positioned for rapid export to Southeast Asia, the Middle East, Europe, and the Americas. When you place an urgent order before 14:00 CST, same-day dispatch is standard. Here is what the logistics chain looks like:

• Day 0: Order confirmed, export documentation prepared — commercial invoice, packing list, certificate of origin
• Day 0–1: DHL Express or FedEx International Priority pickup from Xiamen
• Day 1–3: Delivery to most destinations in Southeast Asia, Middle East, and Europe
• Day 2–4: Delivery to North America and South America

All shipments include full export documentation for customs clearance. HS Code 9031.80 applies to proximity transducer systems — we pre-fill this on all commercial invoices to avoid customs delays. For projects requiring an ATA Carnet or specific country import permits, contact us in advance and we will coordinate.

Anti-static packaging is standard. The probe tip is protected with a machined cap during transit. Extension cable connectors are individually bagged to prevent contamination. If your receiving inspection requires photographic evidence of packaging condition, request it at order time and we will document the outbound pack.

Contact Information

📧 Email: [email protected]
💬 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.