Bently Nevada 330104-14-20-10-02-00 Proximity Transducer – 3300 XL Series

Bently Nevada 330104-14-20-10-02-00 — 8 mm Eddy-Current Proximity Transducer in the 3300 XL Machinery Monitoring Architecture

The Bently Nevada 330104-14-20-10-02-00 is an 8 mm eddy-current proximity transducer forming the field-sensing element of the 3300 XL proximity transducer system. Within a continuous machinery protection loop, this transducer converts the physical gap between its probe tip and a conductive target surface into a proportional DC voltage signal, providing the raw measurement data consumed by 3300 XL or 3500 Series monitors for radial vibration, axial position, differential expansion, and speed/phase reference functions. The transducer operates on the principle of electromagnetic induction: a high-frequency oscillator in the matched driver (oscillator-demodulator) drives an LC tank circuit through the extension cable; as the conductive target enters the probe’s electromagnetic field, eddy currents are induced on the target surface, loading the tank circuit and producing a measurable impedance shift that is demodulated into a linear DC output. The 14-foot (4.27 m) armored extension cable in this configuration is factory-matched to the probe and driver to maintain system calibration accuracy within OEM-specified tolerances — substituting unmatched cable lengths invalidates the calibration curve.

In rotating machinery protection architectures, the 330104-14-20-10-02-00 is typically installed in pairs at 90° X-Y orientation on fluid-film bearing journals to capture full orbital motion data. The non-contact measurement principle eliminates mechanical wear at the sensing interface, making this transducer suitable for continuous, uninterrupted 24/7 operation across the full machinery lifecycle without scheduled sensor replacement intervals. The probe body is constructed from 316 stainless steel with a PEEK (polyether ether ketone) tip insert, providing chemical resistance against lubricating oils, process gases, and cleaning solvents encountered in turbomachinery environments.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 3300 XL system employs a three-component architecture — probe, extension cable, and oscillator-demodulator driver — that must be treated as a calibrated assembly rather than interchangeable parts. The 330104-14-20-10-02-00 probe is factory-characterized against its matched 14-foot extension cable: the cable’s distributed capacitance and inductance are factored into the driver’s demodulation circuit to produce a linear output across the full 0–200 mil measurement range. Substituting a cable of different length or impedance shifts the resonant frequency of the LC tank circuit, introducing a non-linear scale factor error that cannot be corrected through monitor configuration alone.

EMC Design: The armored stainless-steel cable braid provides a continuous Faraday shield from probe tip to driver input, attenuating capacitively coupled interference from adjacent high-voltage cabling, VFD switching transients, and RF sources common in turbomachinery enclosures. The shield is grounded at the driver end only (single-point grounding) to prevent ground loop currents from modulating the signal path — a design discipline that maintains signal integrity in environments where ground potential differences between machine frame and control cabinet can reach several volts.

Thermal Stability: The PEEK tip insert maintains dimensional stability and dielectric properties across the probe’s rated –35 °C to +177 °C operating envelope. Unlike epoxy-potted alternatives, PEEK’s low coefficient of thermal expansion (47 ppm/°C) minimizes tip geometry variation with temperature, preserving scale factor consistency across steam turbine bearing housings where metal temperatures can cycle significantly during startup and shutdown sequences.

Target Material Sensitivity: The eddy-current field penetration depth is a function of target material conductivity and permeability. The 3300 XL system is factory-calibrated against AISI 4140 steel (the API 670 standard target material). When installed on shafts of differing alloy composition — such as 17-4 PH stainless or Inconel — a material correction factor must be applied during commissioning to maintain measurement accuracy within ±1% of full scale.

System Integration Benefits

• Deterministic real-time response: The DC-to-10 kHz frequency response captures sub-synchronous instabilities (oil whirl, oil whip), synchronous 1X imbalance vectors, and super-synchronous blade-pass frequencies within a single transducer channel, eliminating the need for frequency-band-specific sensors in most turbomachinery applications.
• Direct API 670 compliance: The 330104-14-20-10-02-00 meets API Standard 670 (5th Edition) requirements for proximity transducer systems used in machinery protection, simplifying compliance documentation for new installations and insurance audits.
• Zero-wear sensing interface: Non-contact operation eliminates the sensor degradation mechanisms (contact fatigue, fretting corrosion) that affect accelerometers mounted on bearing housings, maintaining measurement baseline stability over multi-year operating periods without recalibration.
• Orbital plot reconstruction: When deployed in X-Y pairs at 90° orientation, the two-channel output enables full shaft orbital reconstruction in Bently Nevada System 1 software, providing diagnostic data on bearing clearance consumption, misalignment, and rotor dynamic instability modes.
• Axial position monitoring: A single 330104 channel configured for axial (thrust) position measurement provides continuous thrust bearing wear indication with sub-mil resolution, enabling predictive maintenance decisions before catastrophic thrust failure.
• Intrinsically safe deployment: ATEX/FM-certified variants of the 330104 series permit installation in Zone 1/Division 1 hazardous areas (flammable gas atmospheres) without additional barriers in some configurations, reducing installation complexity in upstream oil and gas applications.
• Diagnostic transparency via bias voltage monitoring: The –24 VDC bias output serves as a continuous self-diagnostic indicator: a bias voltage outside the –18 to –22 VDC window at nominal gap indicates probe-to-target gap error, cable open/short circuit, or driver fault — providing actionable fault isolation data without removing the transducer from service.
• Backward compatibility with 3500 Series monitors: The 3300 XL transducer system interfaces directly with 3500 Series monitor input cards without signal conditioning adapters, protecting existing monitor infrastructure investments when upgrading field sensors.

Quality Assurance & Global Logistics

Every Bently Nevada 330104-14-20-10-02-00 unit supplied through siemensplc.com is sourced from verified OEM supply channels. Units are inspected against Bently Nevada factory specifications covering probe tip geometry, cable continuity and shield integrity, connector seating torque, and label traceability. Functional verification confirms bias voltage output within the –23 to –25 VDC window at the reference gap before dispatch.

Shipments originate from our warehouse in Xiamen, China, with access to DHL Express, FedEx International Priority, and UPS Worldwide Expedited services. In-stock units are dispatched within 24 hours of payment confirmation. Each shipment includes a commercial invoice, packing list, and certificate of conformance. Export classification and customs documentation are prepared in compliance with applicable trade regulations for the destination country. Anti-static foam-lined transit cases protect probe tip geometry and cable terminations during international freight handling. A 12-month warranty covers manufacturing defects from the date of shipment.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.