Bently Nevada 330130-045-00-05 Extension Cable – 3300 XL Series

Bently Nevada 330130-045-00-05 — 4.5 m Armored Extension Cable for 3300 XL Proximity Transducer Systems

The 330130-045-00-05 is a factory-matched, 4.5-metre (15-foot) armored extension cable manufactured by Bently Nevada as an integral component of the 3300 XL Proximity Transducer System. Its function is to transmit the high-frequency eddy-current signal from the proximity probe tip to the Proximitor® sensor with zero impedance deviation from the matched-set calibration baseline. In rotating machinery protection architectures, signal integrity across this cable segment directly determines the accuracy of shaft radial vibration, axial position, and differential expansion measurements fed into the monitoring rack.

This cable is not a generic coaxial assembly. Its electrical characteristics — distributed capacitance, inductance per unit length, and characteristic impedance — are specified and verified at the factory to maintain the 3300 XL system’s published sensitivity of 200 mV/mil (7.87 V/mm) and linear measurement range of 0.25 mm to 2.26 mm (10 mil to 89 mil) gap. Substituting a non-matched cable of equivalent physical length will shift the system gap voltage and compress or expand the linear output range, invalidating the calibration without triggering any self-diagnostic alarm — a silent failure mode with serious consequences in API 670-governed machinery protection loops.

Deployment environments for this cable include steam turbine bearing pedestals, centrifugal compressor casings, boiler feed pump bearing housings, large synchronous motor end-shields, LNG compressor strings, and offshore platform rotating machinery trains. In each of these applications, the cable must survive sustained exposure to lubricating oil mist, process gas condensate, steam, and mechanical vibration transmitted through the machine structure — conditions that the armored stainless steel braid jacket and PTFE inner insulation are specifically engineered to withstand.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 3300 XL proximity transducer system operates on the eddy-current principle: the proximity probe generates a radio-frequency oscillating magnetic field (nominally 1 MHz carrier) that induces eddy currents in the conductive target shaft surface. The Proximitor® sensor demodulates the resulting impedance change into a DC voltage proportional to the probe-to-shaft gap. The extension cable is the passive transmission medium between these two active elements, but its passive characteristics are not trivial.

Impedance matching and distributed parameter control: The cable’s characteristic impedance is held to a tight tolerance to prevent reflections at the BNC junctions. Any impedance discontinuity at the connector interfaces or along the cable length would superimpose a standing-wave artifact on the 1 MHz carrier, introducing a systematic offset error in the demodulated DC output. The factory-matched set eliminates this variable by specifying the cable as a calibrated component, not a commodity interconnect.

EMC shielding architecture: The stainless steel braid jacket provides a continuous Faraday shield around the signal conductor. In turbine and compressor environments, the cable routes through areas with high magnetic flux density from adjacent motor windings, variable-frequency drives, and bus bars. The braid’s transfer impedance specification ensures that induced common-mode noise on the shield does not couple into the center conductor at levels that would corrupt the low-amplitude vibration signal — particularly critical when measuring sub-25-micron shaft motion at the alarm threshold.

Thermal stability of dielectric: PTFE (polytetrafluoroethylene) insulation maintains a stable dielectric constant (εr ≈ 2.1) across the full operating temperature range of −40 °C to +177 °C. Temperature-induced variation in dielectric constant would alter the cable’s distributed capacitance per unit length, shifting the system’s effective gap voltage and introducing a temperature-correlated measurement drift. PTFE’s near-zero temperature coefficient of dielectric constant eliminates this error source without requiring temperature compensation in the Proximitor® electronics.

Mechanical armor and fatigue resistance: The stainless steel braid armor is not merely a chemical barrier — it provides radial crush resistance and limits the minimum bend radius to prevent center-conductor deformation during installation in confined bearing pedestal access paths. In applications where the cable must pass through a conduit fitting or a machine casing penetration, the armor prevents the jacket from being pinched to a radius that would alter the cable geometry and, consequently, its electrical parameters.

System Integration Benefits

• Preserves factory calibration without field re-ranging: Because the 330130-045-00-05 is a matched-set component, replacing a damaged cable with the identical part number restores the system to its original calibrated state. No gap voltage re-measurement, no sensitivity re-verification, and no monitor card re-ranging are required — reducing maintenance outage duration to the time needed for physical cable replacement and connector re-torque.
• Maintains API 670 5th Edition compliance: Machinery protection systems in regulated facilities (power generation, oil & gas, petrochemical) must demonstrate compliance with API 670 for insurance, regulatory, and OEM warranty purposes. Using the specified matched-set extension cable is a prerequisite for that compliance claim; substituting a non-listed cable voids the system’s API 670 certification status.
• Supports deterministic alarm response: The 3300 XL system’s alarm setpoints are calibrated against the matched-set output curve. A correctly installed 330130-045-00-05 ensures that the monitor card’s danger and alert thresholds correspond to actual shaft displacement values, not to an offset introduced by a mismatched cable. This is the foundation of deterministic machinery protection — the alarm fires at the correct physical threshold, not at an arbitrary electrical level.
• Eliminates silent calibration drift: A non-matched cable introduces a systematic gap voltage offset that does not trigger any self-diagnostic alarm in the Proximitor® or monitor card. The 330130-045-00-05, as the OEM-specified component, eliminates this failure mode by design — the system’s built-in OK relay and gap voltage monitoring circuits operate within their specified windows when the correct cable is installed.
• Reduces spare-parts complexity: Stocking the 330130-045-00-05 as a direct OEM replacement eliminates the need to maintain calibration records for field-assembled cable substitutes. One part number, one calibration state, one procurement record — consistent with the documentation requirements of ISO 55001 asset management frameworks.
• Compatible with 3500 series rack monitoring: The 3300 XL transducer system interfaces directly with Bently Nevada 3500/40M, 3500/42M, and 3500/45 monitor cards. The matched-set cable ensures that the signal presented to the monitor card’s input terminals is within the card’s specified input range, preventing input saturation or under-range conditions that would generate nuisance alarms during startup transients.
• Supports SIL-rated functional safety configurations: In IEC 61511 safety instrumented system (SIS) applications where the proximity transducer loop is part of a safety function (e.g., high-vibration shutdown), the use of OEM-specified components is a requirement of the safety case. The 330130-045-00-05 supports the documented hardware fault tolerance and diagnostic coverage claims of the 3300 XL system’s safety manual.
• Withstands process environment chemical exposure: The PTFE jacket and stainless steel armor resist degradation from turbine lube oil, synthetic compressor lubricants, hydrogen sulfide (H₂S) in sour gas service, steam condensate, and cleaning solvents used during maintenance outages. This chemical resistance profile extends the cable’s service life beyond that of PVC- or polyethylene-jacketed alternatives in the same environment.

Quality Assurance & Global Logistics

Every 330130-045-00-05 unit supplied through siemensplc.com is sourced as genuine Bently Nevada (Baker Hughes) OEM product. Each unit undergoes pre-shipment inspection covering connector seating integrity, jacket continuity, armor braid coverage uniformity, and label accuracy against the part number and revision level. Units that do not pass inspection are not listed or dispatched.

Shipments originate from our warehouse in Xiamen, China, a major international logistics hub with direct access to DHL Express, FedEx International Priority, UPS Worldwide Express, and TNT Economy Express services. Standard export documentation — commercial invoice, packing list, and certificate of origin — is prepared for every shipment. For regulated-industry procurement, a Konmask inspection record and, where available, OEM certificate of conformance (CoC) can be provided upon request at time of order.

Typical dispatch lead time for in-stock units is 1–3 business days from order confirmation. Air freight transit times to major industrial centers: Europe 3–5 days, North America 4–6 days, Middle East 3–4 days, Southeast Asia 2–3 days. For project-critical procurement with a defined shutdown window, contact us in advance to confirm stock availability and reserve units.

All units are shipped in original manufacturer packaging where available, with anti-static and moisture-barrier protection for long-term storage compatibility. A 12-month warranty from date of shipment covers manufacturing defects and connector integrity under normal operating conditions.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.