Bently Nevada 330901-27-46-10-02-00 Proximity Transducer – 3300 XL NSv

Bently Nevada 330901-27-46-10-02-00 — Eddy-Current Proximity Transducer for Critical Rotating Machinery Protection

The Bently Nevada 330901-27-46-10-02-00 is a 3300 XL NSv Series proximity transducer engineered for continuous, non-contact radial shaft displacement and vibration measurement in turbomachinery protection systems. Operating on the eddy-current principle, the probe generates a high-frequency electromagnetic field (nominally 1.0 MHz) that interacts with the conductive target surface. As shaft-to-probe gap varies, the reflected impedance modulates the oscillator circuit within the paired Proximitor sensor, producing a DC-coupled output voltage proportional to displacement — with no mechanical wear, no contact fatigue, and no lubrication requirement.

Within a control loop, this transducer occupies the sensing layer of a three-element chain: probe → extension cable → Proximitor sensor. The 330901-27-46-10-02-00 is configured with a 27 mm probe body diameter, 46 mil (1.17 mm) nominal gap, 10 m integral cable, and a standard coaxial termination compatible with Bently Nevada 330130/330180 extension cables. The output sensitivity of 200 mV/mil (7.87 V/mm) feeds directly into 3300/16 or 3500/42M monitor cards, where the analog signal is digitized, compared against alarm setpoints, and acted upon in deterministic scan cycles — typically sub-10 ms for the 3500 platform.

In API 670-compliant machinery protection architectures, this transducer is the primary sensing element for radial vibration (channels X and Y, 90° apart) and axial position monitoring. Its DC-to-10,000 Hz frequency response captures both low-speed runout (1× and 2× components) and high-frequency structural resonances, making it suitable for steam turbines, gas compressors, centrifugal pumps, and gearboxes operating from 600 RPM to beyond 60,000 RPM.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330901-27-46-10-02-00 implements a three-wire coaxial architecture: the center conductor carries the RF excitation signal from the Proximitor oscillator; the inner shield provides the return path and acts as a driven guard to suppress parasitic capacitance along the cable run; the outer shield is grounded at the Proximitor chassis, establishing a Faraday barrier against externally coupled EMI. This triaxial arrangement is critical in high-voltage switchgear bays and motor control centers where common-mode noise on cable trays can exceed 50 V peak-to-peak.

The probe tip geometry — a flat-faced, recessed coil wound on a ferrite former — concentrates the electromagnetic field into a cone approximately 1.5× the probe diameter in depth. This geometry limits the effective sensing zone to the target surface directly ahead of the probe, rejecting lateral shaft runout from adjacent journals. The PEEK tip housing exhibits a dielectric constant of ε ≈ 3.2, which is stable across the full operating temperature range, preventing thermally induced sensitivity drift that would otherwise require field recalibration during seasonal ambient swings.

The integral 10 m cable uses a low-loss, foam-dielectric coaxial construction with a nominal characteristic impedance of 50 Ω. The cable is terminated with a factory-crimped, hermetically sealed connector that maintains the coaxial geometry to within ±0.5% impedance tolerance — a specification that directly governs the linearity of the output voltage curve across the measurement range. Field-spliced cables introduce impedance discontinuities that degrade linearity; the factory-integral design eliminates this failure mode entirely.

EMC hardening is achieved through the combination of the driven-guard shield, the stainless steel probe body acting as a secondary Faraday enclosure, and the Proximitor’s internal band-pass filter centered on the oscillator frequency. The result is a system-level conducted emissions profile that meets EN 61000-4-6 (10 V/m, 150 kHz – 80 MHz) without external filtering — a meaningful advantage in petrochemical plants where VFD-driven motors generate broadband conducted interference across the same cable trays.

System Integration Benefits

• Deterministic real-time response: The DC-coupled output eliminates AC coupling phase lag, allowing the 3500 monitor to resolve shaft position changes within a single scan cycle (<10 ms), meeting API 670 trip response requirements without firmware compensation.
• Zero-wear sensing: No mechanical contact with the rotating shaft means probe sensitivity remains within ±1% of factory calibration for the full service interval — typically 5 years between scheduled inspections in clean environments.
• Direct monitor compatibility: The −18 VDC nominal output and 200 mV/mil sensitivity are factory-matched to Bently Nevada 3300/16 and 3500/42M input cards, eliminating the need for signal conditioning modules or scaling resistors.
• Diagnostic transparency: The linear output voltage provides a continuous, analog health indicator: a slow drift toward the rail voltages (−24 VDC or 0 VDC) indicates probe gap migration, cable degradation, or target surface contamination — all diagnosable without removing the probe from service.
• Broad frequency coverage: The DC-to-10,000 Hz bandwidth captures sub-synchronous instabilities (oil whirl at 0.43–0.48×), synchronous imbalance (1×), misalignment (2×), and blade-pass frequencies in a single channel — reducing the sensor count required for comprehensive machinery health monitoring.
• Chemical and thermal resilience: The PEEK tip and 316 SS housing withstand H₂S-bearing process gases, steam condensate, and lube oil at temperatures up to 121 °C, covering the majority of refinery and power-generation installation environments without special probe variants.
• Plug-compatible replacement: The 330901-27-46-10-02-00 is a direct dimensional and electrical replacement for earlier 3300 XL 8 mm probes with equivalent gap and cable configurations, enabling in-situ swap without re-gapping or recalibration of the monitor card.
• Redundancy-ready architecture: The probe’s passive electrical characteristics allow dual-probe XY configurations to share a common Proximitor chassis without cross-channel interference, supporting 1oo2 and 2oo3 voting logic in safety-instrumented machinery protection systems.

Quality Assurance & Global Logistics

Every unit of the 330901-27-46-10-02-00 supplied by siemensplc.com is sourced from verified Bently Nevada (Baker Hughes) authorized distribution channels. Each probe undergoes incoming inspection against the OEM datasheet: label traceability, connector integrity, cable sheath continuity, and coaxial impedance verification using a calibrated vector network analyzer. Units that deviate from the factory impedance specification (50 Ω ± 2%) are quarantined and returned — not sold.

Shipments originate from our Xiamen, China warehouse, with access to DHL Express, FedEx International Priority, and UPS Worldwide services. Standard in-stock orders are dispatched within 1–3 business days. Export documentation — commercial invoice, packing list, HS code 9031.80 classification, and Certificate of Conformance — is prepared for every shipment. For project orders requiring 5+ units, consolidated air freight with a single customs entry is available to reduce per-unit landed cost. All shipments carry full end-to-end tracking and are insured at declared value.

A 12-month warranty covers manufacturing defects from the date of dispatch. Defective units are replaced or credited; no restocking fee applies to warranty returns. Optional extended coverage and spare-parts kitting (probe + extension cable + Proximitor) are available on request.

Contact Information

📧 Email: [email protected]
📱 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
📍 Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.