Bently Nevada 330905-00-11-05-01-00 Proximity Transducer System – 3300 XL NSv

Bently Nevada 330905-00-11-05-01-00 — Eddy-Current Proximity Transducer System for Critical Rotating Machinery

The Bently Nevada 330905-00-11-05-01-00 is a complete, factory-matched eddy-current proximity transducer system belonging to the 3300 XL NSv (Non-Standard Voltage) series. It is engineered for continuous, non-contact measurement of shaft radial vibration and axial position in high-speed rotating machinery operating under API 670 machinery protection requirements. The system ships as a calibrated assembly comprising an 11 mm probe tip, a 5-metre extension cable, and a compatible driver/oscillator-demodulator, eliminating field calibration uncertainty and ensuring measurement traceability from the factory.

Unlike general-purpose inductive sensors, the 330905-00-11-05-01-00 operates on the eddy-current principle: a high-frequency oscillator (typically 1.0 MHz carrier) drives the probe coil, and the impedance change induced by the conductive target surface is demodulated into a DC-proportional output voltage. The NSv designation specifies a –24 VDC supply rail, distinguishing it from the standard –18 VDC variant and making it the correct selection for legacy Bently Nevada 3300 monitoring racks that were factory-configured for the higher supply voltage. Substituting a standard-voltage probe into an NSv rack without driver modification will produce a systematic offset error of approximately 15–20% across the full measurement range — a failure mode that is not always flagged by the monitor’s built-in diagnostics.

The 11 mm probe tip diameter provides a linear measurement range of 0.25 mm to 2.25 mm (10 mil to 90 mil) against a standard AISI 4140 steel target, with a nominal sensitivity of 7.87 V/mm (200 mV/mil). This geometry is the preferred choice for shaft diameters above 50 mm where a larger sensing face improves signal-to-noise ratio in the presence of surface finish irregularities or minor shaft runout. The 5-metre extension cable (suffix -05) covers the majority of turbine pedestal and compressor skid installations without requiring a field-spliced extension, which would introduce impedance discontinuities and degrade high-frequency response.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330905-00-11-05-01-00 implements a three-component matched-impedance architecture. The probe coil, extension cable, and oscillator-demodulator driver are calibrated as a single electrical network at the factory. The coaxial extension cable is not a passive conductor — its distributed capacitance and inductance are factored into the driver’s compensation network. Replacing any single component with an unmatched unit shifts the resonant frequency of the LC tank circuit, producing a non-linear output that cannot be corrected by zero/span adjustment alone.

EMC Design: The probe body is constructed from 316 stainless steel with a PEEK (polyether ether ketone) tip housing, providing both chemical resistance and electrical isolation between the coil assembly and the machine structure. The coaxial cable shield is grounded at the driver end only (single-point grounding), preventing ground-loop currents from modulating the carrier signal — a common source of 50/60 Hz interference in plant environments with multiple earthing points.

Thermal Stability: The driver circuit incorporates a temperature-compensated oscillator that maintains carrier frequency within ±0.5% across the full –35 °C to +85 °C operating range. This is critical for steam turbine applications where bearing housing temperatures can vary by 40–60 °C between cold-start and full-load conditions. Without thermal compensation, sensitivity drift would introduce a false DC offset indistinguishable from actual shaft position change.

Target Material Correction: The standard calibration curve is referenced to AISI 4140 steel (relative permeability μr ≈ 100, conductivity σ ≈ 4.0 MS/m). For Inconel 718 targets (μr ≈ 1, σ ≈ 0.8 MS/m), the eddy-current penetration depth increases and sensitivity drops by approximately 8–12%. The NSv driver includes a target material correction factor input, allowing the monitor to apply a software gain adjustment without hardware modification — a feature absent in earlier 3300 standard-voltage drivers.

System Integration Benefits

• Direct rack compatibility: Plug-and-play installation into Bently Nevada 3300/16, 3300/20, and 3300/25 monitoring racks configured for NSv supply, with no wiring modification or driver swap required.
• API 670 5th Edition compliance: The matched-system calibration satisfies the measurement uncertainty requirements of API 670 §6.3, enabling use in machinery protection systems without additional field verification.
• Deterministic frequency response: The flat –3 dB bandwidth of DC to 10,000 Hz covers all subsynchronous, synchronous, and supersynchronous vibration components up to 600,000 RPM (10,000 Hz = 600 kcpm), supporting both protection and diagnostic functions from a single transducer.
• Diagnostic transparency: The driver’s OK relay output de-energizes when the probe gap falls outside the linear range or the cable is open/shorted, providing a hardware-level fault signal to the monitor without requiring software polling — reducing diagnostic latency to <100 ms.
• DCS/PLC integration: The –24 VDC output is compatible with standard 4–20 mA signal conditioners (e.g., Bently Nevada 3300/55) for direct integration into Siemens S7, Rockwell ControlLogix, or Honeywell Experion DCS analog input modules.
• Reduced commissioning time: Factory-matched calibration eliminates the 2–4 hour field calibration procedure required for unmatched component assemblies, directly reducing plant commissioning cost.
• Long-term measurement stability: The PEEK tip housing resists oil, steam condensate, and common process chemicals, maintaining probe geometry and therefore sensitivity within ±1% over a 5-year service interval under normal operating conditions.
• Redundancy architecture support: The compact 11 mm probe diameter allows dual-probe installation in standard API 670 proximity probe brackets (minimum 90° angular separation), supporting 1oo2 or 2oo2 voting logic in safety-instrumented machinery protection systems.

Quality Assurance & Global Logistics

Every unit of the 330905-00-11-05-01-00 supplied through siemensplc.com is sourced from authorized Bently Nevada (Baker Hughes) distribution channels or verified surplus stock with full traceability documentation. Pre-shipment inspection covers visual examination, dimensional verification of the probe tip and cable assembly, and functional output verification against the factory calibration curve using a calibrated gap simulator. Units that deviate more than ±2% from the nominal sensitivity specification are rejected and not offered for sale.

Shipments originate from our warehouse in Xiamen, China — a major international logistics hub with direct air freight connections to Singapore, Dubai, Frankfurt, Los Angeles, and Tokyo. Standard export documentation includes commercial invoice, packing list, and certificate of origin. For regulated industries, we can provide ECCN classification confirmation and end-user declaration support. Typical air freight transit times are 3–5 business days to Southeast Asia and the Middle East, 5–7 business days to Europe, and 6–8 business days to North America. In-stock units are dispatched within 24 hours of payment confirmation. A 12-month warranty covers manufacturing defects and measurement performance; warranty claims are processed with a target replacement dispatch of 5 business days.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.