Bently Nevada 330910-00-02-50-02-00 Proximity Transducer – 3300 XL NSv

Bently Nevada 330910-00-02-50-02-00 — Non-Contact Shaft Measurement in Non-Standard Voltage Environments

The Bently Nevada 330910-00-02-50-02-00 is an eddy-current proximity transducer belonging to the 3300 XL NSv (Non-Standard Voltage) series. It is purpose-built for continuous, non-contact measurement of shaft radial vibration, axial position, and differential expansion on critical rotating machinery. Unlike standard 3300 XL variants that operate on a ±24 VDC supply rail, the NSv configuration accommodates non-standard supply voltages, making it directly applicable to legacy DCS architectures, international plant installations, and brownfield retrofits where standard driver supply rails are unavailable or impractical to retrofit.

The transducer operates on the eddy-current induction principle: a high-frequency oscillator within the driver module energizes the probe coil, generating an electromagnetic field at the probe tip. When a conductive target — the rotating shaft — enters this field, eddy currents are induced on the shaft surface, loading the oscillator circuit. The driver demodulates this loading into a DC voltage output linearly proportional to the gap between probe tip and shaft surface. The 330910-00-02-50-02-00 delivers a nominal sensitivity of 7.87 V/mm (200 mV/mil) across a linear measurement range of 0.25 mm to 2.26 mm (10 to 89 mil), providing the resolution required for API 670-compliant machinery protection systems.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330910-00-02-50-02-00 probe assembly integrates a wound coil encapsulated in a thermally stable, chemically resistant housing. The coil geometry is precision-wound to maintain consistent inductance across the rated temperature envelope, which is critical because inductance drift directly translates to sensitivity error in eddy-current systems. At +177 °C — the probe’s upper thermal limit — the coil inductance variation is held within the manufacturer’s calibrated compensation range, ensuring the driver’s demodulation circuit continues to output a linear voltage without field recalibration.

The NSv designation affects the driver module, not the probe coil itself. The driver’s oscillator is tuned to a specific carrier frequency (typically in the 500 kHz range for 3300 XL systems) and the demodulator is calibrated to the probe’s impedance characteristics. In the NSv variant, the power supply conditioning stage within the driver is redesigned to accept a non-standard input voltage while maintaining the regulated internal supply required by the oscillator and demodulator circuits. This architecture isolates the measurement chain from supply voltage fluctuations, preserving output accuracy even when the plant supply rail is outside the ±24 VDC standard.

From an EMC standpoint, the probe cable is a coaxial assembly with a defined characteristic impedance. The cable length — 5.0 m in this configuration — is matched to the driver’s cable compensation network. Substituting a cable of different length without recalibrating the driver will shift the linear range and sensitivity, a common field error that this specific part number eliminates by providing a factory-matched probe-cable assembly. The armored outer jacket provides mechanical protection and a degree of shielding against radiated interference in high-noise industrial environments, though the primary EMC defense is the differential signal architecture within the driver module itself.

The probe tip’s stainless steel housing is non-magnetic, preventing any interaction between the probe body and the shaft’s magnetic field during operation. This is particularly relevant in applications involving generators or motors where stray magnetic flux is present. The eddy-current field penetration depth is a function of carrier frequency and target material conductivity; for standard carbon steel shafts, the penetration depth at 500 kHz is approximately 0.1 mm, meaning the measurement reflects surface displacement rather than bulk shaft movement — a characteristic that makes the system sensitive to shaft surface finish and any conductive coatings applied to the shaft.

System Integration Benefits

• API 670 Compliance: The 3300 XL NSv system meets the measurement accuracy and response time requirements of API Standard 670 (Machinery Protection Systems), enabling direct use in API-compliant protection loops without additional signal conditioning.
• Deterministic Response Time: The driver’s analog output updates continuously with no digital sampling latency, providing a measurement bandwidth sufficient to capture sub-synchronous vibration events and blade-pass frequencies in high-speed machinery.
• Direct Monitor Compatibility: The DC voltage output is directly compatible with Bently Nevada 3500 series monitor card inputs (3500/42M, 3500/45, 3500/46M), eliminating the need for signal converters or intermediate I/O modules.
• Legacy Plant Integration: The NSv supply configuration allows installation in plants where the control system infrastructure predates the ±24 VDC standard, avoiding costly power supply upgrades during machinery protection retrofits.
• Hazardous Area Deployment: ATEX and IECEx certifications support Zone 1 and Zone 2 classified area installation, covering the majority of oil and gas, petrochemical, and refining applications without additional barrier hardware in many configurations.
• Diagnostic Transparency: The analog output voltage at any gap value is predictable from the calibration curve, allowing maintenance engineers to verify probe gap and system health using a standard DC voltmeter without specialized test equipment.
• Reduced Commissioning Risk: Factory-matched probe and cable assembly eliminates the cable-length calibration variable, reducing commissioning errors and shortening loop verification time during plant startup.
• System 1 Software Integration: When connected through a 3500 series rack, measurement data feeds directly into Bently Nevada System 1 Evolution software for trend analysis, alarm management, and predictive maintenance workflows.
• Wide Thermal Operating Range: The probe’s −35 °C to +177 °C rating covers both arctic outdoor installations and hot-section bearing pedestals on gas turbines, eliminating the need for thermal management accessories in most applications.
• No Scheduled Calibration Drift: Eddy-current transducers exhibit no mechanical wear and maintain calibration stability over multi-year service intervals, reducing the frequency of mandatory calibration outages compared to contact-type sensors.

Quality Assurance & Global Logistics

Every Bently Nevada 330910-00-02-50-02-00 unit supplied through siemensplc.com is sourced as genuine OEM stock. Prior to shipment, each unit undergoes visual inspection covering connector pin integrity, cable jacket condition, probe tip surface, and label traceability against the manufacturer’s part number documentation. Units are packaged in anti-static, moisture-barrier materials with foam cushioning to withstand international air freight handling.

Shipments originate from our warehouse in Xiamen, China, a major export hub with direct access to international air cargo services via Xiamen Gaoqi International Airport and sea freight through Xiamen Port. Standard delivery to Southeast Asia, the Middle East, and Europe is achieved within 3–7 business days via DHL, FedEx, or UPS express services. For urgent plant shutdown requirements, same-day dispatch on in-stock units is available upon order confirmation before 14:00 CST.

Full export documentation is provided with every shipment: commercial invoice, packing list, certificate of origin, and airway bill. For regulated destinations, additional documentation including end-user declarations can be arranged upon request. Our logistics team has experience with customs clearance requirements across Asia-Pacific, the EU, GCC countries, and North America.

All units carry a 12-month warranty from the shipment date covering manufacturing defects and functional failures under normal operating conditions. Warranty claims are processed with a target response time of 48 hours, and replacement units are dispatched from stock where available.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.