Bently Nevada 330106-05-30-02-CN Proximity Probe – 3300 XL Series

Bently Nevada 330106-05-30-02-CN: 8mm Eddy-Current Proximity Probe for Critical Machinery Protection

The Bently Nevada 330106-05-30-02-CN is an 8mm eddy-current proximity probe engineered for continuous, non-contact shaft displacement measurement in rotating machinery protection systems. As the primary sensing element within the 3300 XL Proximity Transducer System, this probe delivers a calibrated DC voltage output proportional to the gap between its tip and the target shaft surface — providing the real-time radial vibration and axial position data that machinery protection logic depends on. Its 5mm linear measurement range, 30-inch (762mm) integral cable, and -02-CN field connector make it a direct-fit replacement in the vast majority of existing 3300 XL installations without requiring proximitor recalibration.

📩 Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330106-05-30-02-CN operates on the principle of high-frequency eddy-current induction. An LC oscillator circuit within the proximitor module drives a sinusoidal current through the probe coil at approximately 1 MHz. This generates an alternating magnetic field that penetrates the conductive target surface, inducing circulating eddy currents. The magnitude of these eddy currents is inversely proportional to the probe-to-target gap: as the shaft approaches the probe tip, eddy-current losses increase, loading the oscillator and reducing its output amplitude. The proximitor’s demodulation stage converts this amplitude variation into a linear DC voltage — nominally –200 mV per mil (7.87 V/mm) of gap change — across the 5mm calibrated range.

The 8mm tip diameter is a deliberate mechanical and electromagnetic design choice. A larger coil diameter increases the effective sensing field depth and improves linearity across the measurement range compared to smaller 5mm probes, while remaining compact enough for installation in standard API 670 probe holder assemblies. The 316 stainless steel body provides corrosion resistance in oil-mist and steam environments without introducing ferromagnetic interference into the sensing field.

EMC performance is addressed at the cable level. The integral 30-inch coaxial cable uses a low-loss dielectric and a continuous shield braid referenced to the proximitor ground, attenuating radiated interference from adjacent VFDs, switchgear, and high-current bus bars. The total system cable length — probe integral plus extension — must match the proximitor’s factory calibration length to maintain the 200 mV/mil sensitivity specification; deviating from the calibrated length shifts the oscillator operating point and introduces a systematic gain error that cannot be corrected in software without recalibration.

The DC-to-10 kHz frequency response is a defining characteristic that separates eddy-current proximity probes from velocity transducers and accelerometers. DC response allows simultaneous measurement of static shaft position (average gap) and dynamic vibration amplitude within a single output channel. This is mandatory for axial thrust position monitoring, where a static displacement of 0.5–1.0 mm toward a thrust bearing indicates impending failure — a condition that an AC-coupled sensor would completely miss. The 10 kHz upper bandwidth captures sub-synchronous instabilities (oil whirl, oil whip), synchronous 1× and 2× components, and blade-pass frequencies in multi-stage compressors, providing the spectral content required for full vibration signature analysis.

System Integration Benefits

• Direct API 670 Compliance: The 330106-05-30-02-CN meets the electrical and mechanical requirements of API Standard 670 (5th Edition) for non-contacting vibration and position measurement systems, enabling use in machinery protection installations subject to refinery and petrochemical plant standards without additional qualification testing.
• Zero-Recalibration Replacement: When replacing a failed 330106-05-30-02-CN with an identical part number and the same total cable length, the proximitor’s calibration constants remain valid. No field recalibration is required, reducing mean time to repair (MTTR) to the time needed for mechanical probe installation and gap setting.
• Deterministic Output Latency: The analog DC output of the transducer system has no digital processing latency. The proximitor output tracks shaft displacement in real time, with the only delay being the RC filter time constant (typically <1 ms for standard bandwidth settings). This deterministic response is essential for machinery protection systems where trip response time is specified in milliseconds.
• Dual-Function Measurement Channel: A single probe installation simultaneously provides shaft radial vibration (dynamic AC component) and shaft centerline position (DC component) to the monitor. This eliminates the need for separate position sensors in many applications, reducing installation hardware count and potential failure points.
• Diagnostic Transparency via Gap Voltage: The raw DC gap voltage is accessible at the proximitor output and at the 3500 monitor front panel. Technicians can verify probe installation gap (typically 1.0–1.5 mm for 8mm probes, corresponding to approximately –10 VDC) with a standard voltmeter, without requiring specialized calibration equipment or software tools.
• Broad DCS/PLC Interfacing: The –2 VDC to –18 VDC output is compatible with Bently Nevada 3500 Series monitors, which provide 4–20 mA and relay outputs for integration with Siemens PCS 7, ABB System 800xA, Honeywell Experion, and other DCS platforms. Direct 4–20 mA conversion modules are also available for legacy PLC analog input cards.
• Hazardous Area Suitability: ATEX and IECEx certifications allow installation in Zone 1 and Zone 2 classified areas (gas groups IIA, IIB) when used with appropriately certified proximitor modules and associated apparatus, covering the majority of oil and gas processing environments.
• Long-Term Spare Parts Availability: The 3300 XL series has been in continuous production for over two decades. The 330106 probe family remains the current standard, ensuring spare parts availability and backward compatibility with installed 3300 XL and 3500 Series infrastructure for the foreseeable service life of existing machinery trains.

Quality Assurance & Global Logistics

Every Bently Nevada 330106-05-30-02-CN unit supplied through siemensplc.com is sourced as genuine OEM product from authorized distribution channels. Each unit undergoes a structured pre-dispatch verification process:

• Part Number Authentication: Dataplate, label, and packaging cross-referenced against Bently Nevada / Baker Hughes part numbering conventions and known genuine product characteristics.
• Physical Integrity Inspection: Probe tip surface, cable jacket continuity, connector pin condition, and thread integrity inspected prior to packaging.
• Documentation Package: Factory calibration certificates and material traceability records provided upon request at time of order.
• Protective Packaging: Units dispatched in anti-static, moisture-barrier packaging with foam probe tip protection to prevent transit damage to the sensing coil assembly.
• 12-Month Warranty: All units carry a 12-month warranty against manufacturing defects from date of dispatch, with DOA replacement policy.

Logistics are managed from our warehouse in Xiamen, China, with access to major international freight carriers including DHL Express, FedEx International Priority, and UPS Worldwide Expedited. Standard export documentation (commercial invoice, packing list, certificate of origin) is prepared for all international shipments. Expedited air freight to Europe, North America, Southeast Asia, and the Middle East typically achieves 3–5 business day door-to-door transit. For time-critical plant shutdowns or emergency replacements, same-day dispatch is available on confirmed in-stock units.

Contact Information

📧 Email: [email protected]
💬 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
📍 Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.