Bently Nevada 330101-24-35-10-02-00 Proximity Probe

330101-24-35-10-02-00 — Every Hour of Downtime Costs More Than This Probe

Your turbine is down. The control room is on the phone. Maintenance is standing by. You already know the shaft vibration monitor tripped — and you’ve traced it back to the proximity probe. The Bently Nevada 330101-24-35-10-02-00 is a 3300 XL 8mm eddy-current proximity transducer with a 24-inch probe body and 35-inch integral cable. It’s not a complex part to identify, but it’s a critical one. Without it, your rotating machinery protection system is blind.

We stock this exact part number in Xiamen. Not a substitute. Not a compatible alternative. The 330101-24-35-10-02-00 — verified, packaged, and ready to hand to DHL today.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

After ten years of field work, here’s what actually goes wrong with the 330101-24-35-10-02-00 and what to watch for during swap-out:

Fault Code 01 / Gap Voltage Out of Range: This is the most common alarm you’ll see on a 3500 rack when this probe degrades. The Proximitor (driver) expects a gap voltage between –10 VDC and –18 VDC at nominal air gap (typically 50 mil / 1.27 mm for 8mm probes). If you’re reading outside this window — say –7 V or –22 V — the probe tip is either damaged, the target surface is corroded, or the probe has shifted axially. Before condemning the probe, verify the extension cable connection at both ends. A loose BNC or corroded pin will give you identical symptoms.

Matched System Requirement — Do Not Skip This: The 3300 XL system is a calibrated three-component assembly: probe + extension cable + Proximitor. The 330101-24-35-10-02-00 must be paired with a 330130-XX-XX extension cable of matching length and a 330180 or 330104 series Proximitor. Mixing components from different calibration sets will shift your scale factor and introduce measurement error that won’t trigger a fault — it’ll just give you wrong data. That’s worse than a fault.

Installation Air Gap Setting: After mounting, set the probe-to-target gap to 50 mil (1.27 mm) using a feeler gauge or gap voltage method. At 50 mil, the Proximitor output should read approximately –10 VDC ± 0.5 V. Document this value. If the machine is already running and you’re doing a hot swap on a redundant channel, confirm the new probe’s gap voltage matches the live channel within 0.5 V before switching over.

Thread Engagement & Locknut Torque: The 330101 probe uses a 3/8-24 UNF thread. Torque the locknut to 20–25 in-lb (2.3–2.8 N·m) after gap setting. Over-torquing shifts the gap. Under-torquing causes the probe to walk out under vibration — you’ll see a slow drift in gap voltage over days, not an immediate fault.

Cable Routing: Keep the integral cable away from high-voltage runs and VFD output cables. Induced noise on the coaxial cable will appear as high-frequency content on the vibration spectrum and can cause nuisance trips on the 3500 monitor’s Not-OK relay. Use separate cable trays or maintain at least 150 mm separation from power conductors.

Firmware / Monitor Compatibility: If you’re running a 3500/42M or 3500/45 monitor, confirm the channel is configured for 3300 XL 8mm probe type in the 3500 Rack Configuration Software. Selecting the wrong transducer type changes the full-scale range and alert setpoints. This is a software setting — it doesn’t require hardware changes, but it must match the physical probe.

Reliability in Harsh Conditions

The 330101-24-35-10-02-00 is built for environments that would destroy lesser sensors. The probe tip housing is stainless steel, resistant to the oil mist, process gas condensate, and chemical splash common in turbine bearing pedestals and compressor seal areas. The IP67 rating means it survives temporary immersion — relevant when bearing housings flood during seal failures or wash-down procedures.

Vibration resistance is not a marketing claim here. The probe body is designed to operate continuously in environments with broadband vibration up to 20g RMS. The integral cable uses a reinforced jacket rated for repeated flexing — critical in applications where the cable runs through areas subject to structural vibration from adjacent machinery. We’ve seen probes from lesser suppliers fail at the cable-to-body junction within months in high-vibration compressor trains. The OEM construction on the 330101 addresses this with a strain-relief design at the probe body exit.

Temperature performance is equally serious. The –35°C to +121°C probe tip rating covers arctic outdoor installations and hot gas path adjacency in gas turbines. The Proximitor electronics are separately rated and should be located in a cooler environment — but the probe itself can sit in the heat. This is by design for steam turbine applications where bearing metal temperatures run high.

Global Express Logistics

Our warehouse is in Xiamen, China — one of the country’s primary export hubs with direct DHL and FedEx gateway access. Here’s how a typical urgent order moves:

Day 0 (Order Confirmed): Payment or PO received before 15:00 CST. Unit pulled from stock, inspected, and packaged with original documentation. Commercial invoice and packing list prepared with correct HS Code (8543.70 for proximity transducers).

Day 0 – Evening: Shipment handed to DHL Express or FedEx International Priority at Xiamen pickup. Tracking number issued and sent to buyer within 2 hours of handover.

Day 1–3 (Transit): DHL Express from Xiamen typically delivers to Southeast Asia in 1–2 days, Middle East and Europe in 2–3 days, and Americas in 3–4 days. FedEx International Priority follows similar timelines. We select the carrier based on your destination and any import compliance requirements.

Customs Documentation: We prepare complete export documentation including commercial invoice, packing list, and certificate of origin. For ATEX-sensitive destinations or countries with import licensing requirements for industrial electronics, we advise in advance. We do not under-declare value — all documentation is accurate and compliant.

Bulk Orders: For 5+ units or mixed part number orders, we can consolidate into a single shipment to reduce freight cost. Contact us for a freight quote before ordering if volume is significant.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.