Bently Nevada 330103-00-08-05-02-05 Proximity Probe – 3300 XL Series

Bently Nevada 330103-00-08-05-02-05 — 8mm Eddy-Current Proximity Probe for Continuous Shaft Vibration and Position Monitoring

The Bently Nevada 330103-00-08-05-02-05 is an 8mm eddy-current proximity probe belonging to the 3300 XL Series, engineered for non-contact, continuous measurement of radial shaft vibration, axial position, and differential expansion on critical rotating machinery. Operating on the principle of electromagnetic induction, the probe generates a high-frequency oscillating magnetic field at its tip; when a conductive target surface enters the field, eddy currents are induced, attenuating the field in direct proportion to the gap distance. This gap-to-voltage conversion is processed by the matched 3300 XL Proximitor to deliver a calibrated –24 VDC bias output with a sensitivity of 7.87 V/mm (200 mV/mil), providing a linear measurement range of 0.25 mm to 2.26 mm (10–89 mil).

Within a machinery protection architecture, this probe occupies the first node of the measurement chain: mechanical displacement → electromagnetic transduction → analog voltage → monitor rack digitization → alarm/trip logic. Its accuracy and long-term stability directly determine the integrity of every downstream protection decision. The 330103-00-08-05-02-05 suffix encodes the probe’s physical configuration: 8mm tip diameter, 5-metre integral armored cable, standard connector, and metric thread body (M10 × 1.0), making it a direct-fit replacement across the installed base of 3300 XL and 3500 Series monitoring systems worldwide.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330103-00-08-05-02-05 probe body is constructed from 316L stainless steel, selected for its non-magnetic permeability (μr ≈ 1.008) which prevents the housing from interfering with the probe’s own electromagnetic field topology. The sensing coil is wound on a ferrite core and encapsulated in a thermally stable epoxy compound rated to 177°C, maintaining coil geometry — and therefore sensitivity linearity — across the full operating temperature envelope. Thermal expansion of the coil former is matched to the ferrite core’s coefficient to suppress thermally induced sensitivity drift to below ±0.5% over the rated range.

The integral 5-metre cable uses a triaxial construction: the inner conductor carries the RF oscillator signal, the intermediate shield provides a driven guard to eliminate cable capacitance from the measurement loop, and the outer braid provides EMC shielding against radiated interference. This driven-guard topology is critical in high-EMI environments such as variable-frequency drive (VFD) motor rooms or switchgear enclosures, where unguarded coaxial cables would introduce capacitive loading errors of several millivolts — sufficient to corrupt gap readings by tens of micrometers.

The M10 × 1.0 thread pitch is finer than the M10 × 1.25 general-purpose standard, providing 25% greater axial positioning resolution per turn during installation. This allows maintenance technicians to set the probe gap to the OEM-specified 1.0 mm (40 mil) nominal with a single-turn adjustment range of 1.0 mm, enabling repeatable gap setting without feeler gauges in confined bearing housings. The armored cable jacket — a stainless steel braid over a fluoropolymer inner — withstands continuous exposure to turbine lube oil, steam condensate, and hydrogen seal gas without jacket degradation or conductor insulation compromise.

System Integration Benefits

• Direct 3500 Rack Compatibility: The probe’s –24 VDC output and 7.87 V/mm sensitivity are factory-matched to the 3500 Series monitor input cards, eliminating the need for signal conditioning or scaling adjustments during rack configuration.
• Deterministic Alarm Response: The analog output path from probe tip to monitor rack input introduces less than 2 µs of signal propagation delay, ensuring that shaft displacement events are captured within the monitor’s 1 ms sampling window without aliasing.
• Dual-Voting Architecture Support: Two probes mounted at 90° (X–Y configuration) on the same bearing journal provide orthogonal displacement vectors, enabling the 3500/40M monitor to compute orbit plots and apply dual-voting trip logic — reducing spurious trips while maintaining protection integrity.
• Keyphasor Phase Reference: When used as a once-per-revolution phase reference probe, the 330103-00-08-05-02-05 provides a clean notch pulse with a rise time below 50 µs, sufficient for accurate phase angle computation at shaft speeds up to 60,000 RPM.
• System 1 Software Integration: The probe’s calibration data (sensitivity, bias voltage, linear range) is stored in the 3500 rack’s non-volatile memory and automatically imported into Bently Nevada System 1 Evolution, enabling trend analysis, alarm setpoint management, and predictive maintenance workflows without manual re-entry.
• Hot-Swap Replacement: The probe can be replaced without powering down the monitor rack. The 3500 rack’s channel-level OK relay drops during probe disconnection, logging a diagnostic event, and automatically resets upon reconnection and gap verification — minimizing maintenance window duration.
• Diagnostic Transparency: The Proximitor’s OK output provides a continuous hardware health signal. A gap outside the linear range (probe too close or too far) drives the OK relay open, generating a channel-level alert in System 1 before any process alarm threshold is reached — providing early warning of probe mounting drift.
• Multi-Machine Scalability: A single 3500 rack can accommodate up to 16 probe channels using the same 330103-series probes, allowing a standardized spare-parts inventory across an entire turbine train — compressor, gearbox, and driven equipment — without probe-type proliferation.

Quality Assurance & Global Logistics

Every 330103-00-08-05-02-05 unit supplied by siemensplc.com is sourced as genuine Bently Nevada OEM product. Units are procured through verified industrial supply channels and are not refurbished, re-labeled, or modified in any form. Each probe undergoes the following pre-shipment verification protocol at our Xiamen facility:

Electrical Verification: Coil DC resistance is measured and compared against the OEM specification (nominal 8.5 Ω ± 5%). Insulation resistance between the inner conductor and outer shield is tested at 500 VDC; minimum acceptable value is 100 MΩ. Connector contact resistance is verified below 10 mΩ using a four-wire milliohm measurement.

Physical Inspection: Probe tip surface, thread condition, cable jacket integrity, and connector pin geometry are inspected under 10× magnification. Label markings — part number, serial number, and date code — are cross-referenced against the accompanying Certificate of Conformance (CoC).

Documentation Package: Each shipment includes the original OEM CoC, a packing list with individual serial numbers, and a commercial invoice with HS Code 9031.80 declaration for customs clearance.

Logistics are managed from Xiamen, China, with DHL Express and FedEx International Priority as primary carriers. In-stock units are dispatched within 1–2 business days of order confirmation. Estimated transit times: Southeast Asia 2–3 days, Europe 3–5 days, North America 4–6 days, Middle East 3–5 days. Bulk orders (5+ units) qualify for consolidated sea freight with full export documentation. All shipments comply with applicable export control regulations.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.