Bently Nevada 330103-01-08-10-02-00 Proximity Transducer – 3300 XL Series

Bently Nevada 330103-01-08-10-02-00 — Eddy-Current Proximity Transducer for Rotating Machinery Condition Monitoring

The Bently Nevada 330103-01-08-10-02-00 is a 3300 XL Series eddy-current proximity transducer engineered for continuous, non-contact measurement of radial shaft vibration, axial position, and differential expansion in critical rotating machinery. Operating on the principle of electromagnetic induction, the transducer generates a high-frequency oscillating magnetic field at its tip; as a conductive target surface approaches, eddy currents are induced, loading the oscillator circuit and producing a proportional DC voltage output. This physical mechanism delivers a linear, repeatable signal across the full measurement range without any mechanical contact with the rotating shaft — eliminating wear as a failure mode and enabling indefinite service life under normal operating conditions.

Within a control loop architecture, the 330103-01-08-10-02-00 occupies the sensing layer between the rotating shaft and the signal conditioning stage. Its output feeds directly into a compatible Bently Nevada Proximitor sensor (e.g., 330180 series), which provides the oscillator drive voltage and converts the raw impedance change into a calibrated millivolt-per-mil or volt-per-millimeter signal. This conditioned signal is then routed to a 3300 series monitor module for threshold comparison, alarm generation, and integration with plant DCS or safety instrumented systems. The transducer’s DC-to-10,000 Hz frequency response ensures that both quasi-static position measurements (e.g., rotor thermal growth at startup) and high-frequency vibration events (e.g., blade-pass frequencies in multi-stage compressors) are captured within a single measurement channel.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

Oscillator Circuit Stability and EMC Design: The 330103-01-08-10-02-00 integrates a temperature-compensated LC oscillator within the probe tip assembly. The oscillator frequency is selected to minimize susceptibility to conducted and radiated interference from adjacent power cables, variable-frequency drives, and high-current bus bars — all common in turbomachinery enclosures. The coil geometry is wound to a tight impedance tolerance, ensuring that the sensitivity coefficient (7.87 V/mm) remains within ±1% across the full operating temperature range without field recalibration. This thermal stability is achieved through matched-coefficient winding materials and a hermetically sealed tip construction that prevents moisture ingress from steam or process gas environments.

Cable Impedance Matching and Signal Integrity: The integral 1.0 m cable is impedance-matched to the Proximitor driver circuit. The cable’s characteristic impedance is controlled to prevent reflections that would introduce measurement error at frequencies above 5 kHz — relevant for blade-pass and gear-mesh frequency monitoring. The cable shield is terminated at the Proximitor end only (single-point grounding), eliminating ground loop currents that would appear as low-frequency noise on the output signal. In installations where the probe-to-Proximitor distance exceeds 1.0 m, a matched extension cable (330130 series) must be used; mismatched cable impedance degrades sensitivity linearity and can shift the calibrated gap range by up to 8%.

Mechanical Mounting and Thermal Expansion Compensation: The 3/8-24 UNF-2A thread provides a defined torque-to-clamp-load relationship, allowing the probe to be locked at a precise axial position within the bearing housing bracket. The 316L stainless steel body has a coefficient of thermal expansion (CTE) of approximately 16 µm/m·°C, which must be accounted for in installations where the bracket and shaft materials differ significantly. In high-temperature applications (bearing housings above 120°C), the probe body CTE introduces a predictable gap drift of approximately 0.16 µm per °C per millimeter of probe insertion depth — a value that can be compensated in the monitor’s gap alarm setpoints.

Eddy-Current Depth of Penetration and Target Geometry: At the operating frequency of the 330103 oscillator, the skin depth in AISI 4140 steel is approximately 0.08 mm. This means the eddy currents are confined to a thin surface layer of the shaft, making the measurement insensitive to shaft core material variations or internal defects. However, surface finish and hardness variations on the shaft target area directly affect sensitivity. Bently Nevada specifies a target surface finish of Ra ≤ 0.8 µm and a minimum target diameter of 25 mm to ensure the calibrated sensitivity coefficient applies. Shaft runout, eccentricity, and surface irregularities within the target zone appear directly in the transducer output and must be characterized during slow-roll calibration.

System Integration Benefits

• Direct rack compatibility: The 330103-01-08-10-02-00 is factory-calibrated to the 3300 XL system sensitivity standard (7.87 V/mm), allowing direct substitution into existing 3300/16, 3300/20, and 3300/25 monitor racks without recalibration of the monitor channel.
• Deterministic latency contribution: The transducer’s analog output introduces zero processing latency — the signal is a continuous, real-time voltage proportional to gap. This preserves the deterministic response characteristic of the overall monitoring chain, where total latency from shaft displacement to alarm relay output is governed solely by the monitor’s digital processing cycle (typically <100 ms for 3300 series monitors).
• Dual-measurement capability: A single 330103 channel can simultaneously provide radial vibration (AC component, filtered above 1 Hz) and average shaft centerline position (DC component) to the monitor, reducing channel count and wiring complexity compared to separate vibration and position sensors.
• Hazardous area deployment: ATEX and FM certifications (configuration-dependent) allow installation in Zone 1/Division 1 classified areas without additional intrinsic safety barriers, simplifying the installation design for offshore platforms and petrochemical facilities.
• API 670 compliance: The 3300 XL system, including the 330103 transducer, meets the requirements of API Standard 670 (Machinery Protection Systems), enabling direct use in machinery protection applications for new installations and retrofits subject to API specification.
• Diagnostic transparency via gap voltage monitoring: The DC gap voltage output provides a continuous, observable indicator of probe-to-shaft clearance. Gradual drift in the DC level — visible in the monitor’s gap display — provides early warning of bearing wear, shaft thermal growth anomalies, or probe mounting looseness before vibration alarm thresholds are reached.
• System 1 software integration: The transducer’s output is fully compatible with Bently Nevada System 1 Evolution condition monitoring software, enabling trend logging, spectral analysis, and machine train visualization without signal conversion or scaling adjustments.
• Reduced commissioning time: Factory-matched sensitivity and pre-terminated MIL-C-5015 connectors eliminate field calibration steps at installation. The probe can be installed, gap-set using the DC voltage output, and placed in service within a single maintenance window.

Quality Assurance & Global Logistics

Every 330103-01-08-10-02-00 unit supplied through siemensplc.com is a genuine Bently Nevada (Baker Hughes) OEM component. Units are procured through verified industrial supply channels and undergo a structured pre-shipment inspection covering housing integrity, connector condition, cable sheathing continuity, and label authenticity against factory reference standards. Functional output verification is performed where test infrastructure permits, confirming that the oscillator circuit is active and the output voltage responds correctly to a conductive target approach.

Shipments originate from Xiamen, China, with access to major international freight forwarders and express courier networks (DHL, FedEx, UPS, SF International). Standard in-stock orders are dispatched within 2–3 business days of payment confirmation. Full export documentation is provided with every shipment, including commercial invoice, packing list, and certificate of origin. Anti-static packaging with foam cushioning protects the probe tip and cable assembly during transit. For time-critical plant shutdowns or emergency replacements, expedited air freight options are available — contact the sales team directly to confirm lead time and routing for your destination.

A 12-month warranty covers manufacturing defects and functional failures under normal operating conditions from the date of shipment. Warranty claims are processed with replacement unit dispatch or credit note issuance within 5 business days of confirmed fault diagnosis.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.