Bently Nevada 330104-00-05-05-02-05 Proximity Transducer – 3300 XL Series

Bently Nevada 330104-00-05-05-02-05 — 8 mm Eddy-Current Proximity Transducer for Critical Rotating Machinery Protection

The Bently Nevada 330104-00-05-05-02-05 is an 8 mm eddy-current proximity transducer belonging to the 3300 XL Series — a platform that has defined the benchmark for non-contact shaft measurement in turbomachinery protection systems for over three decades. This specific configuration ships with a 5-metre probe cable and a 5-metre armored extension cable, terminated with a standard MIL-C-5015 connector, and is factory-calibrated against AISI 4140 steel targets to a scale factor of 7.87 V/mm (200 mV/mil).

In a rotating machinery protection loop, the transducer occupies the first and most critical node: it converts mechanical displacement into a proportional DC voltage signal with a frequency response flat from DC to 10,000 Hz. This bandwidth is sufficient to capture sub-synchronous instabilities, synchronous unbalance vectors, and high-frequency rubs without signal attenuation. The output range of −1 VDC to −17 VDC maps directly to the linear measurement gap of 0.25 mm to 2.25 mm, giving the downstream monitor a 2.0 mm usable window — adequate for API 670-compliant radial vibration and axial position channels on most industrial turbines and compressors.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330104-00-05-05-02-05 operates on the principle of high-frequency electromagnetic induction. The probe coil, driven by an oscillator circuit inside the paired driver (e.g., 3300/16 or 3500/42), generates an alternating magnetic field at approximately 1 MHz. When a conductive target enters the field, eddy currents are induced on the target surface, loading the coil and reducing its Q-factor. The driver’s demodulation circuit converts this impedance change into a DC voltage proportional to the air gap — a relationship that remains linear within the 0.25 mm to 2.25 mm window.

EMC Design: The probe body is constructed from 316L stainless steel with a PEEK (polyether ether ketone) tip insert. This material combination provides both chemical resistance and electrical isolation of the coil from the probe housing, suppressing common-mode noise pickup. The armored extension cable in this configuration (-05 suffix) uses a double-shielded coaxial construction: an inner braid shield tied to the driver’s signal reference, and an outer foil shield connected to chassis ground at the driver end only — a single-point grounding topology that prevents ground loop currents from corrupting the low-level voltage signal.

Thermal Stability: The coil winding uses a temperature-compensated formulation that maintains scale factor accuracy within ±0.5% across the full −35 °C to +121 °C probe operating range. This is critical in steam turbine applications where bearing housing temperatures can vary by 60–80 °C between cold startup and full-load steady state. Without this compensation, a thermally naive transducer would introduce a false DC offset that the monitor could misinterpret as shaft position drift.

Mechanical Integrity: The probe tip geometry is precision-machined to maintain coil-to-tip concentricity within 0.05 mm. Deviations beyond this tolerance alter the effective sensing field geometry and shift the calibration curve. The MIL-C-5015 connector provides IP67 ingress protection and a positive locking bayonet mechanism rated for 500 mating cycles — relevant in installations where the transducer is removed during scheduled outages.

System Integration Benefits

• Direct compatibility with 3300 and 3500 series monitors: The 330104-00-05-05-02-05 is electrically matched to Bently Nevada 3300/16, 3300/20, 3300/25, 3500/40, 3500/42, and 3500/45 monitors without any signal conditioning adapter, eliminating impedance mismatch errors that degrade measurement accuracy.
• Deterministic signal latency: The eddy-current transduction chain introduces less than 50 µs of signal delay from mechanical displacement to voltage output, ensuring that the monitor’s alarm and trip logic operates on data that accurately reflects the shaft’s instantaneous position — a requirement for overspeed and high-vibration trip systems where response time is safety-critical.
• Keyphasor phase reference capability: When installed opposite a shaft notch or keyway, this transducer generates a once-per-revolution pulse that synchronizes vector analysis in ADRE and System 1 software, enabling precise identification of unbalance, misalignment, and resonance frequencies without additional hardware.
• Dual-channel redundancy support: Two 330104-00-05-05-02-05 units installed 90° apart on the same bearing journal provide X-Y orbit data. The 3500 series monitor processes both channels simultaneously to compute shaft centerline position and dynamic orbit shape — a diagnostic capability that distinguishes fluid-film instability from mechanical rub with high confidence.
• Axial position measurement: When paired with a thrust collar target, the same transducer model measures axial shaft displacement with a resolution of approximately 0.025 mm, sufficient to detect thrust bearing wear before it reaches the API 670 danger threshold.
• System 1 software integration: The transducer’s output feeds directly into Emerson’s System 1 condition monitoring platform, where trend data, alarm states, and waveform captures are stored with millisecond timestamps. This data structure supports root-cause analysis without requiring additional signal acquisition hardware.
• Third-party DCS/PLC interfacing: The −24 VDC supply and voltage output are compatible with standard signal conditioning modules (e.g., MTL 787+, P+F KFD2-VR4) that convert the transducer output to a 4–20 mA loop signal, enabling integration with Siemens S7, ABB 800xA, Honeywell Experion, and Yokogawa CENTUM VP distributed control systems.
• Hazardous area deployment: With the optional ATEX/FM certification variant, the transducer can be installed in Zone 1 / Division 1 classified areas when used with an approved intrinsically safe barrier, extending its applicability to offshore platforms, LNG terminals, and petrochemical reactors where gas detection requirements apply.

Quality Assurance & Global Logistics

Every Bently Nevada 330104-00-05-05-02-05 unit supplied by siemensplc.com is sourced through verified industrial supply channels and undergoes a structured pre-dispatch inspection protocol. Visual examination confirms connector integrity, cable jacket condition, and probe tip concentricity. Functional verification checks the coil impedance against the factory specification to confirm the sensing element has not been damaged during storage or transit. Units that pass inspection are packaged in anti-static, moisture-sealed enclosures with original labeling and batch traceability documentation preserved.

Certificates of Conformance (CoC) and calibration records are available on request for all units. For projects requiring third-party inspection or witnessed testing, arrangements can be made prior to dispatch.

Logistics operations are based in Xiamen, China — a major southeastern port city with direct air freight connections to Singapore, Dubai, Frankfurt, Los Angeles, and Tokyo. In-stock units are dispatched within 1–3 business days via DHL Express, FedEx International Priority, or UPS Worldwide Expedited, with typical transit times of 3–7 business days to most destinations. For large-volume orders or projects requiring DDP (Delivered Duty Paid) or DAP (Delivered at Place) Incoterms, consolidated sea-air freight options are available with customs clearance handled by our licensed freight forwarder. Export documentation including commercial invoice, packing list, and certificate of origin is prepared for all international shipments.

The 12-month warranty covers manufacturing defects and confirmed calibration drift beyond the published specification. Warranty claims are processed with a target response time of 48 hours from receipt of the defective unit.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.