Siemens 6ES7288-3AQ04-0AA0 Analog Output Module – S7-200 SMART

Siemens 6ES7288-3AQ04-0AA0 — 4-Channel Analog Output Module for S7-200 SMART Control Loops

The 6ES7288-3AQ04-0AA0 is a dedicated analog output expansion module within the Siemens S7-200 SMART series, engineered to deliver stable, high-resolution setpoint signals to field actuators including variable-frequency drives, proportional valves, electro-pneumatic positioners, and process controllers. Each of its four output channels operates independently, configurable in software for either voltage mode (±10 V) or current mode (0–20 mA / 4–20 mA), making it applicable across a broad range of process industries without hardware modification.

In a closed-loop control architecture, the module occupies the command-output stage of the control chain: the S7-200 SMART CPU executes the PID or sequential logic, writes a 16-bit word to the module’s process image output (PIQ), and the module converts that digital word into a proportional analog signal within a settling time of under 1 ms. This deterministic output latency is critical in applications such as VFD speed reference control, where signal jitter directly translates to mechanical speed variation and process instability.

The module connects to the CPU via the S7-200 SMART side-bus expansion connector, drawing 24 V DC bus power directly from the CPU’s integrated power rail. No separate field-side power supply is required for the output stage in voltage mode; current-loop mode requires a field-side loop supply of 24 V DC with a maximum load impedance of 500 Ω. The compact 45 × 100 × 81 mm housing mounts on standard 35 mm DIN rail and occupies a single expansion slot, preserving panel real estate in space-constrained enclosures.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 6ES7288-3AQ04-0AA0 implements a sigma-delta (ΣΔ) digital-to-analog conversion architecture at its output stage. Unlike successive-approximation DACs, the sigma-delta topology achieves inherently low differential non-linearity (DNL) error across the full 12-bit code range, which is particularly important in current-loop applications where mid-scale accuracy determines valve positioning precision in throttling control.

Optical Isolation Architecture: Each channel’s digital control signal crosses the logic-to-field boundary through a dedicated optocoupler stage. The isolation barrier sustains a rated working voltage of 500 V AC, providing protection against common-mode transients originating from inductive field loads — a frequent failure mode in installations where VFD output cables run parallel to analog signal wiring. The isolation capacitance across the barrier is kept below 10 pF, limiting high-frequency noise coupling from the field side into the CPU’s logic domain.

EMC Design: The module’s PCB layout routes analog output traces with a dedicated ground plane beneath, minimizing loop area and reducing susceptibility to radiated magnetic fields. The housing incorporates a conductive backplane contact that bonds the DIN rail to the module’s chassis ground, providing a low-impedance path for shield currents. This design approach aligns with IEC 61000-4-4 (electrical fast transient / burst) and IEC 61000-4-6 (conducted disturbances) immunity requirements, both of which are verified during Siemens’ production qualification testing.

Output Short-Circuit Protection: Each analog output channel incorporates electronic current limiting. In voltage mode, a short circuit to ground limits output current to a safe level and the channel recovers automatically upon fault clearance — no manual reset or module replacement is required. This self-recovery behavior reduces unplanned downtime in applications where wiring faults are a maintenance reality.

Bus Interface Timing: The module communicates with the S7-200 SMART CPU via the proprietary side-bus protocol, which operates synchronously with the CPU’s scan cycle. Output data is latched at the end of each scan cycle’s output phase, ensuring that all four channels update simultaneously within a single scan — a property that matters in multi-axis coordinated motion or multi-loop ratio control where channel-to-channel skew would introduce process error.

System Integration Benefits

• Zero-configuration channel mode switching: Voltage or current output mode is selected via STEP 7-Micro/WIN SMART software parameters, with no hardware jumpers or DIP switches required. This eliminates field wiring errors caused by incorrect jumper settings and allows remote reconfiguration without panel access.
• Deterministic scan-cycle output update: All four channels refresh simultaneously at the end of each CPU scan cycle, guaranteeing channel-to-channel synchronization within ±1 scan period — typically under 10 ms for standard S7-200 SMART programs. This is essential for multi-loop ratio control and coordinated actuator positioning.
• Integrated diagnostics via CPU status bits: The module reports output wire-break detection (in 4–20 mA mode) and supply voltage faults directly to the CPU’s special memory (SM) area. The CPU program can read these status bits and trigger alarms or safe-state routines without requiring additional diagnostic hardware.
• Plug-and-play expansion without CPU restart: The S7-200 SMART system supports hot-swap of expansion modules during powered operation in certain configurations, reducing commissioning time and allowing staged system build-out without full panel shutdowns.
• Consistent signal quality across temperature range: The ≤ 0.02% / °C temperature drift coefficient ensures that a module calibrated at 25 °C maintains output accuracy within ±1.1% of full scale across the full 0–55 °C operating range — sufficient for most industrial process control tolerances without field recalibration.
• Compact form factor preserves panel density: At 45 mm wide, the module allows up to seven expansion modules in a standard 400 mm wide DIN rail section alongside the CPU, supporting complex multi-loop systems within a single compact enclosure.
• Full STEP 7-Micro/WIN SMART integration: The module appears natively in the hardware configuration wizard, with auto-populated I/O addresses, channel parameter dialogs, and online monitoring of output values in engineering units — reducing configuration time compared to third-party analog modules requiring manual address mapping.
• Backward compatibility across S7-200 SMART CPU generations: The module operates with all current S7-200 SMART CPU variants (SR and ST series), protecting the hardware investment when upgrading CPU firmware or replacing CPUs with higher-performance variants without changing the expansion module population.

Quality Assurance & Global Logistics

Every 6ES7288-3AQ04-0AA0 unit supplied by siemensplc.com is sourced as genuine Siemens factory-manufactured product. Siemens AG produces the S7-200 SMART series to ISO 9001-certified manufacturing standards, with each module undergoing automated functional test on the production line before packaging. Units are shipped in original Siemens anti-static packaging with factory labels intact, including the Siemens order number, date code, and country of origin markings.

Our warehouse is located in Xiamen, China — a major logistics hub with direct access to international freight forwarding services via Xiamen Gaoqi International Airport and Xiamen Port. In-stock orders confirmed before 15:00 CST are dispatched the same business day. International shipments are handled via DHL Express, FedEx International Priority, and UPS Worldwide Expedited, with typical transit times of 3–5 business days to Southeast Asia, 4–6 days to the Middle East and Europe, and 5–7 days to North America.

Export documentation — including commercial invoice, packing list, and certificate of origin — is prepared for every international shipment. The applicable HS Code for this module is 8537.10.9000. For buyers in the EU, US, or other regulated markets requiring additional import documentation, our logistics team provides pre-shipment coordination to minimize customs clearance delays.

All units carry a 12-month warranty against manufacturing defects from the date of confirmed delivery. Dead-on-arrival (DOA) units are replaced at no charge within 7 business days of receipt, subject to photographic evidence of the fault condition. Warranty claims are processed directly by our technical team without requiring return to Siemens AG, minimizing downtime for the end user.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.