Bently Nevada 330130-080-02-00 Extension Cable – 3300 XL Series

Bently Nevada 330130-080-02-00 — 8-Meter Coaxial Extension Cable for 3300 XL Proximity Transducer Systems

The 330130-080-02-00 is a factory-calibrated, 8-meter armored coaxial extension cable manufactured by Bently Nevada (a Baker Hughes company) for exclusive use within the 3300 XL Proximity Transducer System. Its primary function is to extend the signal path between a 3300 XL proximity probe and its corresponding Proximitor® sensor where direct probe-to-driver mounting is geometrically or operationally impractical. The cable is not a passive conductor in the conventional sense — it is an integral, impedance-matched component of a three-part measurement chain (probe + extension cable + Proximitor® sensor), and substituting a non-OEM cable of equivalent physical length will introduce calibration offsets that invalidate the system’s output voltage-to-gap relationship.

In rotating machinery protection applications governed by API 670 (5th Edition), the total cable length — integral probe cable plus extension cable — determines the system’s scale factor (typically –7.87 V/mm for 8 mm probes). The 330130-080-02-00 is matched to this calibration curve. Any deviation in cable capacitance or impedance shifts the Proximitor® sensor’s oscillator frequency, producing a measurable DC output error that cannot be corrected through monitor configuration alone.

Deployment environments for this cable include steam and gas turbines requiring continuous shaft radial vibration and axial position monitoring, centrifugal and reciprocating compressors in petrochemical and LNG processing facilities, large pump and fan assemblies where bearing journal orbit analysis is performed, gearboxes requiring differential expansion measurement, and marine propulsion systems on offshore platforms. In each case, the cable must traverse environments characterized by elevated ambient temperature, mechanical vibration, chemical exposure, and — in many installations — classified hazardous areas requiring ATEX or IECEx zone separation between the probe (Zone 1 / Division 1) and the Proximitor® sensor (safe area or Zone 2).

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330130-080-02-00 operates within an eddy-current proximity measurement circuit whose accuracy depends on maintaining a tightly controlled transmission line characteristic from probe tip to Proximitor® sensor input. The Proximitor® sensor drives the probe coil at a fixed RF oscillation frequency (typically 1.0 MHz for 8 mm probes). The extension cable forms the interconnecting transmission line between the probe’s integral cable and the sensor’s input stage. Three hardware design attributes define this cable’s engineering value:

1. Impedance Continuity and Calibration Integrity. The coaxial geometry — center conductor, PTFE dielectric, and braided shield — is manufactured to maintain 50 Ω ± tolerance across the full 8-meter length. Any impedance discontinuity (caused by connector damage, kinking, or moisture ingress) creates a reflection coefficient that alters the effective load seen by the Proximitor® oscillator. This shifts the oscillator’s operating point and produces a DC output offset proportional to the impedance mismatch. The 330130-080-02-00’s factory-matched impedance eliminates this error source when used as a direct OEM replacement.

2. EMC Shielding Architecture. The stainless steel armored braid provides two functions: mechanical protection against abrasion and crush loads, and RF shielding against conducted and radiated electromagnetic interference. In turbine enclosures, high-frequency switching noise from variable-speed drives, ignition systems, and power cables can couple into unshielded signal lines and appear as spurious vibration signals at the monitor. The braid’s transfer impedance — the ratio of induced shield voltage to external field — is sufficiently low to maintain signal integrity in environments with field strengths consistent with IEC 61000-4-3 test levels. The shield is grounded at the Proximitor® sensor end only (single-point grounding) to prevent ground loop currents from modulating the signal.

3. PTFE Dielectric Stability. Polytetrafluoroethylene is selected as the dielectric material for its low and stable relative permittivity (εr ≈ 2.1) across the operating temperature range. Temperature-induced permittivity variation in alternative dielectrics (e.g., polyethylene) would shift the cable’s electrical length and alter the calibration curve. PTFE’s chemical inertness also prevents degradation from turbine oils, hydraulic fluids, steam condensate, and cleaning solvents — all common in the cable’s routing environment.

4. Connector Mechanical Design. The MIL-C-5015 threaded coupling provides a positive mechanical lock that resists vibration-induced loosening — a failure mode that produces intermittent open-circuit faults indistinguishable from probe failures at the monitor level. The metal shell provides 360° shield continuity at the mating interface, preventing the connector junction from becoming an EMC weak point in the signal chain.

System Integration Benefits

• Zero Recalibration on Replacement: Because the 330130-080-02-00 is factory-matched to the 3300 XL calibration curve, swapping a failed cable of the same part number requires no Proximitor® sensor recalibration or monitor rescaling — reducing mean time to repair (MTTR) on critical machinery.
• Deterministic Signal Latency: The cable’s fixed electrical length contributes a known, constant propagation delay to the measurement chain. This determinism is essential in machinery protection systems where the monitor’s response time to a trip condition must be predictable and within API 670 alarm/trip response time requirements.
• Hazardous Area Zone Separation: The 8-meter length provides sufficient physical separation to route the probe through a Zone 1 / Division 1 classified area while locating the Proximitor® sensor in a safe area or Zone 2 enclosure, supporting ATEX/IECEx zoning strategies without requiring intrinsic safety barriers in all installations.
• Diagnostic Transparency: A cable fault (open circuit, short circuit, or high-resistance connection) produces a characteristic out-of-range DC output at the Proximitor® sensor that the 3500 series monitor can detect and flag as a transducer fault — distinguishing cable failures from actual machinery events and preventing false trips.
• Reduced Installed Wiring Complexity: The single coaxial cable replaces multi-conductor field wiring between probe and sensor, reducing termination points, junction box complexity, and potential sources of signal degradation in the field wiring infrastructure.
• Compatibility with Redundant Measurement Architectures: In dual-probe redundant configurations (common on critical turbine shafts), two 330130-080-02-00 cables can be routed independently to separate Proximitor® sensors, ensuring that a single cable failure does not compromise the redundant measurement channel.
• Long-Term Spare Parts Availability: As a catalogued OEM part number within the 3300 XL system, the 330130-080-02-00 is supported by Bently Nevada’s global spare parts infrastructure, ensuring availability for the operational life of installed machinery — typically 20–30 years for large rotating equipment.
• Compliance with Plant QA Documentation Requirements: Each unit is traceable to OEM manufacturing records. Certificate of Conformance (CoC), material test reports, and datasheet documentation are available on request, supporting plant QA processes and regulatory audit requirements.

Quality Assurance & Global Logistics

Every 330130-080-02-00 unit supplied by siemensplc.com is sourced through verified industrial distribution channels and undergoes a pre-shipment inspection protocol before dispatch from our Xiamen, China facility. Inspection steps include visual examination of connector shells, armor braid continuity, and jacket integrity; electrical continuity verification of center conductor and shield; impedance spot-check against OEM specification; and secure anti-static packaging with part number label and lot traceability documentation.

We do not supply counterfeit, refurbished-as-new, or unverified grey-market components. Provenance documentation — including Certificate of Conformance and original manufacturer datasheet — is available upon request at the time of order placement.

Logistics from Xiamen cover all major international trade lanes. Standard in-stock orders are dispatched within 1–3 business days via DHL Express, FedEx International Priority, or UPS Worldwide Expedited, with typical transit times of 3–7 business days to Europe, North America, Southeast Asia, and the Middle East. For project-critical or shutdown-driven requirements, same-day dispatch on confirmed stock is available with prior arrangement. Export documentation — commercial invoice, packing list, and HS Code 8544.42 classification — is prepared for all international shipments. DDP, DAP, and EXW Incoterms are supported.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.