Bently Nevada 330905-00-03-10-02-00 Proximity Extension Cable – 3300 XL Series

Bently Nevada 330905-00-03-10-02-00 — 3300 XL Extension Cable in Rotating Machinery Measurement Chains

The 330905-00-03-10-02-00 is a 3.0 m coaxial extension cable assembly manufactured by Bently Nevada for use within the 3300 XL Proximity Transducer System. Its primary function is to bridge the proximity probe tip and the Proximitor® sensor while preserving the electrical characteristics of the eddy-current measurement loop. In shaft vibration and axial position monitoring applications, any impedance discontinuity introduced at the cable junction directly corrupts the DC gap voltage and AC vibration signal. This assembly is factory-matched to the 3300 XL probe and Proximitor® to eliminate that risk.

Deployed across gas turbine trains, centrifugal compressor strings, steam turbine-generator sets, and high-speed gearboxes, the 330905-00-03-10-02-00 operates as a passive but precision-critical link in a measurement chain that must sustain ±0.5% linearity across the full operating gap range. Its stainless steel armor and fluoropolymer jacket maintain signal integrity under continuous mechanical vibration, oil mist, and thermal cycling — conditions that degrade generic coaxial cable within months.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The eddy-current proximity measurement principle depends on a stable, high-frequency oscillator circuit housed inside the Proximitor® sensor. The oscillator drives a resonant LC tank whose inductance is the probe coil. Any change in the electrical path between probe and Proximitor® — including cable capacitance variation, connector contact resistance drift, or dielectric absorption in the cable insulation — shifts the tank resonant frequency and introduces a systematic error in the gap-to-voltage transfer function.

Bently Nevada addresses this through factory-matched cable assemblies. The 330905-00-03-10-02-00 is manufactured and tested as a system component, not a generic coaxial cable. The distributed capacitance per unit length is controlled to a tight tolerance so that the Proximitor® calibration curve — typically expressed as mV/mil or V/mm — remains valid without field recalibration when this cable replaces a like-for-like unit.

The stainless steel armor serves a dual purpose: mechanical protection against cable tray abrasion and turbomachinery bay vibration, and a degree of electrostatic shielding that supplements the coaxial geometry’s inherent EMC performance. In environments with variable-frequency drive (VFD) switching noise and high-current bus bars in close proximity, the armor reduces capacitively coupled interference that would otherwise appear as broadband noise on the vibration channel — a particularly important consideration in compressor trains where the vibration monitor must resolve sub-mil shaft orbits.

The fluoropolymer jacket resists hydrocarbon fluids, synthetic lubricants, and steam condensate. Unlike PVC-jacketed cables, fluoropolymer does not plasticize or crack under prolonged thermal cycling between ambient and the +121 °C upper limit, which is relevant in steam turbine bearing pedestals where surface temperatures can approach this boundary during load transients.

The factory-terminated connectors use a controlled-torque assembly process. Field-terminated coaxial connectors introduce variable contact resistance at the center pin and outer shell, which manifests as a DC offset error in the gap voltage. The factory termination eliminates this variable, ensuring the connector contributes a repeatable, negligible impedance to the measurement loop.

System Integration Benefits

• Preserved transfer function linearity: Factory-matched capacitance ensures the Proximitor® calibration curve remains within ±0.5% linearity across the 0.25 mm to 2.54 mm gap range without field adjustment.
• Direct drop-in replacement: Identical connector geometry and cable length allow technicians to swap the assembly during a planned outage window without modifying cable routing, conduit fill, or junction box terminations.
• No Proximitor® recalibration required: Because the electrical characteristics are matched to the original factory specification, the paired Proximitor® sensor does not require recalibration after cable replacement — reducing planned maintenance duration.
• Deterministic signal latency: The fixed cable length and controlled dielectric constant produce a predictable signal propagation delay, which is relevant in multi-channel vibration monitors where phase relationships between measurement points are used for orbit analysis and balancing calculations.
• EMC robustness in VFD-dense environments: Stainless steel armor attenuates capacitively coupled switching noise from adjacent VFD power cables, maintaining signal-to-noise ratio on vibration channels monitoring sub-mil shaft motion.
• Thermal stability across duty cycles: Fluoropolymer jacket retains dimensional and dielectric stability from cold-start conditions (–40 °C) through sustained high-temperature operation (+121 °C), eliminating the insulation degradation that causes intermittent faults in PVC-jacketed alternatives.
• API 670 audit compliance: Each assembly is traceable to OEM documentation, supporting the instrumentation loop records required by API 670 machinery protection system audits at refineries and LNG facilities.
• Reduced diagnostic ambiguity: When a vibration channel develops a fault, a known-good, OEM-specification cable eliminates the cable assembly as a variable, allowing maintenance engineers to focus diagnostic effort on the probe tip condition or Proximitor® electronics rather than cable integrity.

Quality Assurance & Global Logistics

Every 330905-00-03-10-02-00 unit dispatched from our Xiamen, China facility is sourced from authorized Bently Nevada distribution channels and verified against OEM dimensional and electrical acceptance criteria before shipment. The inspection process covers connector contact resistance, jacket continuity, armor integrity, and cable length within the specified tolerance.

Units are packaged in anti-static, moisture-barrier polyethylene bags with desiccant inserts, then placed in rigid corrugated cartons rated for international air freight handling. This packaging protocol protects the factory-terminated connectors from mechanical shock and prevents moisture ingress into the coaxial geometry during transit — a failure mode that causes gradual DC offset drift in the gap voltage after installation.

From Xiamen, we ship via DHL Express, FedEx International Priority, and UPS Worldwide Expedited to plant sites across Southeast Asia, the Middle East, Europe, and the Americas. Standard dispatch is within 1–3 business days of order confirmation. For plant emergency and unplanned shutdown scenarios, same-day dispatch is available on confirmed stock with pre-arranged freight accounts.

All shipments include a packing list, commercial invoice with HS code declaration, and a certificate of conformance referencing the OEM part number. For projects requiring material traceability documentation under ISO 9001 or API 670 audit requirements, extended documentation packages are available on request.

A 12-month warranty covers manufacturing defects in materials and workmanship from the date of dispatch. Warranty claims are processed with replacement dispatch within 5 business days of defective unit receipt and inspection.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.