Bently Nevada 330910-03-20-05-11-00 Proximity Probe – 3300 NSv

Bently Nevada 330910-03-20-05-11-00: Eddy-Current Proximity Probe for Critical Rotating Machinery Protection

The Bently Nevada 330910-03-20-05-11-00 is a field-proven eddy-current proximity probe belonging to the 3300 NSv (Non-contact Vibration) Series. It operates on the principle of electromagnetic induction: a high-frequency oscillating current is driven through the probe tip coil, generating an alternating magnetic field. When a conductive target — typically a ferromagnetic shaft — enters this field, eddy currents are induced on the target surface, loading the oscillator circuit and producing a DC output voltage proportional to the gap distance. This non-contact measurement principle eliminates mechanical wear entirely, making the 330910-03-20-05-11-00 a preferred choice for continuous, uninterrupted shaft monitoring in turbines, compressors, and pumps operating under API 670 machinery protection standards.

The suffix structure of this part number encodes precise physical and electrical configuration: 330910 identifies the 3300 NSv probe family; 03 specifies the 3 mm probe tip diameter; 20 denotes a 20 cm integral cable; 05 indicates a 5 m extension cable; 11 defines the M11 thread mount; and 00 confirms the standard connector termination. Each parameter directly governs installation geometry and system compatibility — mismatching any suffix against the Proximitor® sensor specification will result in calibration offset errors.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 3300 NSv probe system is architecturally distinct from earlier 3300 XL variants in its oscillator frequency selection and coil geometry. The 3 mm tip diameter of the 330910-03-20-05-11-00 operates at a higher carrier frequency than 8 mm probes, which narrows the effective linear range but delivers superior spatial resolution — critical in small-shaft applications where shaft diameter is below 50 mm and orbital motion amplitudes are measured in single-digit micrometers.

EMC Design: The probe cable is a coaxial assembly with a continuous shield bonded at the Proximitor® sensor end only (single-point grounding). This topology suppresses common-mode noise injection from adjacent power cables and variable-frequency drives — a persistent interference source in motor control centers. The shield floating at the probe end prevents ground-loop currents that would otherwise appear as low-frequency noise on the vibration signal, corrupting slow-roll compensation data.

Thermal Stability: The coil former material and potting compound are selected for matched thermal expansion coefficients. Over the −35 °C to +177 °C operating envelope, gap-voltage drift is held within ±0.5% of full-scale — a specification that matters in steam turbine bearing housings where metal temperatures cycle significantly between cold startup and full-load operation. Probes that exhibit thermal sensitivity drift will generate false alarm conditions during transient thermal events, triggering unnecessary shutdowns.

Mechanical Robustness: The M11 thread mount provides a larger contact area than M8 alternatives, reducing the risk of probe loosening under sustained vibration. The 20 cm integral cable is armored against oil mist and high-pressure washdown environments rated to IP67, while the 5 m extension cable uses a low-capacitance dielectric to preserve signal bandwidth across the full cable run.

System Integration Benefits

• Direct Proximitor® Compatibility: Matched electrical characteristics with 3300 NSv Proximitor® sensors eliminate the need for external signal conditioning, reducing BOM complexity and potential failure nodes in the signal chain.
• Deterministic Gap Voltage Output: The DC output is linear and monotonic across the full measurement range, enabling the 3500 Series monitor to execute gap alarm logic with sub-millisecond latency — no analog-to-digital conversion delay in the protection path.
• Dual-Variable Measurement: A single probe simultaneously provides radial vibration (AC component) and average shaft centerline position (DC component), reducing the number of penetrations required in the bearing housing and simplifying installation in space-constrained machinery.
• API 670 Compliance: The probe system meets the measurement chain accuracy requirements of API 670 Fifth Edition, allowing direct use in machinery protection systems without additional field calibration when installed per the Bently Nevada System Selection Guide.
• Diagnostic Transparency: The 3500/40M and 3500/42M monitor modules can report probe gap voltage as a continuous process variable via Modbus or OPC-UA, enabling DCS integration for predictive maintenance trending without dedicated vibration analysis software.
• Redundant Probe Configurations: The M11 thread mount is compatible with dual-probe brackets, supporting 1oo2 (one-out-of-two) voting logic in safety-instrumented systems where a single probe failure must not cause a spurious trip.
• Wide Frequency Bandwidth: The 10 kHz flat frequency response captures sub-synchronous instability events (oil whirl, oil whip) and high-frequency blade-pass excitation in addition to 1× and 2× synchronous vibration — providing a complete picture of rotor dynamic behavior from a single sensor.
• Long Cable Run Capability: The 5 m extension cable, combined with the low-impedance Proximitor® driver, maintains signal integrity over total cable runs up to 9 m without signal attenuation or bandwidth degradation, accommodating installations where the junction box cannot be mounted adjacent to the bearing.

Quality Assurance & Global Logistics

Every Bently Nevada 330910-03-20-05-11-00 unit supplied by siemensplc.com is sourced through verified industrial distribution channels with full traceability documentation. Physical inspection covers label integrity, connector pin condition, cable sheathing continuity, and probe tip surface condition. Part number suffix codes are cross-referenced against Bently Nevada’s published product matrix to confirm configuration accuracy before dispatch.

Units are shipped from our Xiamen, China operations hub — a designated free-trade zone with direct access to Xiamen Gaoqi International Airport and Xiamen Port, two of China’s highest-throughput export gateways. This geographic position enables next-flight-out DHL Express and FedEx International Priority dispatch to major industrial centers in Southeast Asia, the Middle East, Europe, and the Americas, with typical transit times of 3–7 business days door-to-door.

Export documentation — commercial invoice, packing list, certificate of origin, and HS Code 9031.80 classification — is prepared in compliance with Xiamen Customs regulations, minimizing clearance delays at destination ports. Multi-currency payment is supported: USD, EUR, CNY, and HKD via T/T bank transfer, PayPal (verified business accounts), and major credit cards. Volume orders of 5 units or more qualify for negotiated pricing and dedicated logistics coordination.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.