Siemens 6GK5008-0BA10-1AB2 Industrial Ethernet Switch – SCALANCE XB008

Siemens 6GK5008-0BA10-1AB2 — 8-Port Unmanaged Switch in PROFINET-Transparent Industrial Ethernet Architecture

The SCALANCE XB008, ordered under MLFB 6GK5008-0BA10-1AB2, is an 8-port unmanaged industrial Ethernet switch designed for deterministic Layer 2 forwarding in factory-floor and process-plant control networks. Unlike managed counterparts, the XB008 operates without a configuration interface, relying entirely on hardware-level MAC address learning and store-and-forward switching to deliver consistent frame delivery latency across all eight 10/100BASE-TX ports. This architecture is deliberate: in PROFINET IO topologies where the controller (IO-Controller) and field devices (IO-Devices) exchange cyclic data frames at intervals as short as 250 µs, any software-induced jitter from a management plane would degrade real-time performance. The XB008 eliminates that variable entirely.

Each RJ45 port supports IEEE 802.3 auto-negotiation and auto-MDI/MDIX crossover detection, allowing direct connection to PLCs, HMIs, drives, remote I/O stations, and panel PCs without patch cable polarity management. The internal switching fabric operates at wire speed for 100 Mbit/s full-duplex traffic, with a maximum frame store buffer sized to absorb burst collisions without frame loss under typical industrial traffic profiles. The store-and-forward method ensures that only frames passing CRC integrity checks are forwarded — corrupted frames are silently discarded at the ingress port, preventing error propagation across the network segment.

Mechanically, the 6GK5008-0BA10-1AB2 occupies a 30 mm DIN rail footprint — the narrowest profile in the SCALANCE XB family — making it the preferred choice for compact control cabinets where horizontal rail space is constrained. The housing is rated IP20, suitable for installation inside sealed enclosures. The unit draws a maximum of 3.5 W from a 24 V DC bus (operating range: 18–32 V DC), with dual redundant power supply terminals wired in parallel. Loss of one supply rail triggers a fault signal on the dedicated signaling contact without interrupting switch operation, enabling predictive maintenance without network downtime.

Thermal management is passive — no fan, no moving parts. The operating temperature range of −10 °C to +60 °C covers the majority of indoor industrial environments, while the storage specification extends to −40 °C / +85 °C for cold-chain logistics and seasonal warehouse conditions. Mean Time Between Failures (MTBF) for the XB008 series exceeds 500,000 hours under rated conditions, consistent with Siemens’ SIMATIC NET component reliability standards.

The 6GK5008-0BA10-1AB2 carries CE, UL 508, cUL, ATEX Zone 2 (II 3 G Ex nA IIC T4 Gc), and IECEx certifications, qualifying it for installation in potentially explosive atmospheres classified as Zone 2 — a requirement in petrochemical, gas processing, and pharmaceutical manufacturing environments where managed switches with active cooling are prohibited.

📦 Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The XB008’s internal architecture centers on a single-chip Layer 2 switching ASIC with an integrated 1,024-entry content-addressable memory (CAM) table for MAC address resolution. Frame forwarding decisions are executed in hardware at sub-microsecond latency per lookup — no CPU arbitration is involved in the data path. This is the fundamental distinction between an unmanaged switch and a managed device: the absence of a management CPU in the forwarding path eliminates the risk of software-induced latency spikes during configuration polling or SNMP trap generation.

EMC performance is addressed at the PCB layout level. The switching ASIC and magnetics (integrated RJ45 transformer modules) are separated by a ground plane pour, reducing common-mode noise coupling between the Ethernet physical layer and the power supply rail. The 24 V DC input passes through an onboard LC filter stage before reaching the DC-DC converter, attenuating conducted emissions in the 150 kHz–30 MHz band per EN 55011 Class A limits. This is particularly relevant in cabinet environments where variable-frequency drives (VFDs) generate significant high-frequency conducted interference on the 24 V bus.

The dual power supply input topology uses a diode-OR circuit: both supply rails are active simultaneously, and the higher-voltage rail supplies the load. If one rail drops below the diode forward voltage threshold, the other rail assumes full load without a switching transient. The signaling relay contact opens on supply loss, providing a dry-contact fault output that can be wired to a PLC digital input or a panel alarm annunciator — enabling supervisory monitoring of switch power health without any network-layer protocol overhead.

Port LEDs (Link/Activity per port, plus Power and Fault indicators) are driven directly from the ASIC’s GPIO outputs, providing real-time physical-layer status without requiring a management interface. In a fault-finding scenario, a technician can identify a disconnected cable, a speed mismatch, or a power supply fault within seconds using visual inspection alone — a meaningful advantage in time-critical maintenance windows.

System Integration Benefits

• Zero-configuration deployment: The XB008 requires no IP address assignment, no VLAN configuration, and no firmware provisioning. Commissioning time is limited to physical installation and cable termination — typically under 10 minutes per unit in a standard cabinet build.
• PROFINET IO cycle integrity: Because the switch introduces no management-plane jitter, PROFINET IO controllers can maintain update rates down to 250 µs without frame loss or cycle overrun errors attributable to the network infrastructure.
• Deterministic forwarding latency: Store-and-forward switching at 100 Mbit/s full-duplex produces a fixed forwarding latency of approximately 6.7 µs per 100-byte frame — predictable and bounded, unlike cut-through switches that vary latency with frame size.
• Seamless TIA Portal topology integration: Although the XB008 has no PROFINET device identity, Siemens’ LLDP-based topology detection in TIA Portal can map the physical network through the switch, allowing accurate network topology visualization in the project tree.
• ATEX Zone 2 compliance: Enables direct installation in Ex-classified areas without requiring an additional Ex-rated enclosure, reducing BOM cost and cabinet complexity in hazardous-area applications.
• Redundant power supply fault detection: The floating relay output integrates directly with SIMATIC S7 digital input modules (e.g., SM 321) or ET 200SP DI modules, enabling PLC-level monitoring of switch power health within the existing I/O budget.
• Compact 30 mm rail footprint: In a 400 mm wide control cabinet with a 300 mm usable DIN rail, up to 10 XB008 units can be mounted side-by-side — sufficient to network an entire machine cell from a single rail section.
• Passive thermal design: No fan means no fan failure mode, no periodic maintenance, and no acoustic noise — relevant in laboratory automation, pharmaceutical cleanrooms, and food-grade production environments where particulate generation and noise are controlled.
• Long-term spare parts availability: As a current-generation SCALANCE XB product, the 6GK5008-0BA10-1AB2 is supported under Siemens’ standard product lifecycle policy, with spare parts availability guaranteed for a minimum of 10 years post-discontinuation.
• Consistent frame error filtering: CRC error frames are dropped at ingress, preventing corrupted frames from consuming bandwidth on downstream segments — a passive quality-of-service mechanism that requires no configuration.

Quality Assurance & Global Logistics

Every 6GK5008-0BA10-1AB2 unit dispatched from our Xiamen, China facility is a genuine Siemens-manufactured component sourced through verified supply channels. Prior to shipment, each unit undergoes a structured inspection protocol: housing and label integrity verification against Siemens’ current production markings, connector pin condition check on all RJ45 ports and terminal blocks, power-on functional test confirming LED status and port link-up, and packaging in anti-static foam with moisture-barrier outer carton.

Export documentation — including commercial invoice, packing list, and certificate of origin — is prepared in compliance with Chinese customs regulations and destination-country import requirements. HS Code 8517.62 applies to this product category for customs classification purposes. Shipping is executed via DHL Express, FedEx International Priority, or UPS Worldwide Expedited, with full tracking provided from collection to delivery. Transit times to major industrial hubs: Europe 3–5 business days, North America 4–6 business days, Southeast Asia 2–3 business days, Middle East 4–7 business days. For orders requiring air freight consolidation or sea freight for large quantities, dedicated logistics coordination is available upon request.

All units are covered by a 12-month warranty from the date of shipment. Warranty claims are processed through our Xiamen technical team, with replacement or credit resolution targeted within 10 business days of confirmed defect verification.

Contact Information

📧 Email: [email protected]
💬 WhatsApp: +86 18359268345
🌐 Web: siemensplc.com
📍 Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.