Bently Nevada 330103-00-11-10-02-00 Proximity Transducer – 3300 XL Series

Bently Nevada 330103-00-11-10-02-00 — Eddy-Current Proximity Transducer for Critical Rotating Machinery Protection

The Bently Nevada 330103-00-11-10-02-00 is an 11 mm eddy-current proximity transducer belonging to the 3300 XL Proximity Transducer System. Within a machinery protection loop, this transducer occupies the first stage of the signal chain: it converts the physical air gap between probe tip and target shaft into a proportional DC voltage, which is then conditioned by a paired Proximitor sensor before being processed by a 3500-series monitor rack. The accuracy of every downstream alarm, trip, and trend record depends entirely on the linearity and thermal stability of this transducer — making component selection at this stage a system-level engineering decision, not a commodity purchase.

The 330103-00-11-10-02-00 variant specifies a 10 ft (3.05 m) integral armored cable, a 3-pin MIL-C-5015 style connector, and a nominal sensitivity of 200 mV/mil (7.87 V/mm). These parameters are factory-calibrated against the companion 3300 XL 8 mm Proximitor sensor to form a matched system with a combined linearity error of less than ±1% over the full linear range. Substituting non-matched components introduces gain offset errors that cannot be corrected by monitor scaling alone.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

Eddy-Current Operating Principle and Gap-to-Voltage Transfer Function. The probe tip houses a wound coil driven by a radio-frequency oscillator embedded in the Proximitor sensor, typically at 1.0 MHz for the 3300 XL system. When the conductive target enters the electromagnetic field, eddy currents are induced on the target surface, loading the oscillator and reducing coil impedance. The Proximitor demodulates this impedance change into a DC output voltage. The 330103-00-11-10-02-00 is factory-characterized so that the transfer function slope — 200 mV/mil — holds within ±1% linearity across the specified 90 mil linear range. This tight tolerance is achieved through individual probe-to-Proximitor matching at the factory, not through generic calibration curves.

EMC Design and Shielding Architecture. The integral cable uses a double-layer shield: an inner foil shield bonded to the probe body ground reference, and an outer braided shield connected at the Proximitor end only. This single-point grounding topology eliminates ground-loop currents that would otherwise appear as low-frequency noise on the output signal — a critical consideration in motor control centers and switchgear rooms where common-mode interference can exceed 10 V. The armored outer jacket provides additional mechanical protection against abrasion and hydrocarbon fluid ingress in turbomachinery enclosures.

Thermal Stability and Compensation. Eddy-current sensitivity is a function of target conductivity, which varies with temperature. The 3300 XL system addresses this through a matched-pair calibration protocol: the Proximitor’s internal compensation network is trimmed to the specific probe coil characteristics, maintaining sensitivity drift below 0.5% per 100°C across the probe’s rated temperature range. For installations where probe temperatures exceed 150°C — such as hot-section gas turbine bearing housings — the 330103 series specifies a high-temperature cable compound rated to 177°C, preventing insulation breakdown that would shift the output bias voltage and trigger false alarms.

Mechanical Integration and Thread Specification. The probe body is machined from 316 stainless steel with an M14×1.0 thread form, providing corrosion resistance in wet gas and steam environments. The locknut and bracket assembly allows axial positioning adjustment in 0.5 mm increments, enabling field technicians to set the initial gap to the nominal 1.0 mm (40 mil) operating point without special tooling. The 11 mm tip diameter provides a larger sensing field than 8 mm variants, improving signal-to-noise ratio on shafts with surface finish Ra values above 1.6 μm.

System Integration Benefits

• Direct API 670 Compliance: The 330103-00-11-10-02-00 meets API 670 5th Edition requirements for proximity transducer systems, eliminating the need for additional qualification testing when specifying machinery protection systems for petrochemical or LNG plant acceptance.
• Matched-System Accuracy: Factory-paired with the 3300 XL 8 mm Proximitor (330180 series), the combined system achieves ±1% linearity — a specification that cannot be replicated by mixing components from different calibration batches or third-party equivalents.
• Deterministic Frequency Response to 10 kHz: The flat frequency response from DC to 10,000 Hz captures both quasi-static position data (thrust position, differential expansion) and high-frequency vibration harmonics up to the 10th order on 60,000 RPM machinery, within a single transducer channel.
• Plug-Compatible with 3500 Monitor Racks: The MIL-C-5015 connector and −24 VDC supply interface are directly compatible with Bently Nevada 3500/40M, 3500/42M, and 3500/45 monitor modules, requiring no signal conditioning adapters or wiring modifications during replacement.
• Reduced Diagnostic Ambiguity: The integral cable eliminates the extension cable junction — a common failure point in three-component transducer systems — reducing the number of potential fault locations from three to one during troubleshooting, which shortens mean time to repair (MTTR) in unplanned outage scenarios.
• Wide Target Material Compatibility: While calibrated for AISI 4140 steel, the 3300 XL system provides documented sensitivity correction factors for common shaft alloys including 17-4 PH stainless, Inconel 718, and titanium, allowing engineers to apply a scalar correction in the monitor configuration rather than procuring a custom-calibrated probe.
• Dual-Use Measurement Capability: A single installed transducer can simultaneously provide radial vibration data (AC component, 1–10,000 Hz bandpass) and average shaft centerline position data (DC component) to the monitor, supporting both machinery protection and condition monitoring functions without additional hardware.
• Long-Term Spare Parts Availability: The 3300 XL series has been in continuous production since the 1990s and remains the dominant proximity transducer standard in the installed base of turbomachinery protection systems globally. Stocking the 330103-00-11-10-02-00 as a critical spare ensures like-for-like replacement without system reconfiguration or monitor rescaling.

Quality Assurance & Global Logistics

Every 330103-00-11-10-02-00 unit supplied by siemensplc.com is sourced as a genuine Bently Nevada (Baker Hughes) OEM component. Each unit is inspected upon receipt for label integrity, connector condition, and part number traceability. Functional verification includes output bias voltage measurement and sensitivity confirmation against the published transfer function prior to shipment.

Shipments originate from our warehouse in Xiamen, China, with access to DHL Express, FedEx International Priority, UPS Worldwide Expedited, and consolidated air freight services. In-stock orders are dispatched within 1–2 business days. DHL/FedEx express transit times to Europe, North America, and Southeast Asia typically range from 3 to 7 business days. Full export documentation — commercial invoice, packing list, certificate of origin, and MSDS where applicable — is prepared for every shipment. Customs HS code 8543.70 applies to proximity transducer systems for most destination markets.

A 12-month warranty covers manufacturing defects and functional non-conformance against published specifications. Warranty claims are processed with replacement shipment or credit note within 5 business days of confirmed defect assessment. All units are packed in anti-static foam-lined cartons with desiccant to prevent moisture ingress during transit.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.