Bently Nevada 330101-00-28-10-12-CN Proximity Transducer – 3300 XL NSv

Bently Nevada 330101-00-28-10-12-CN — Eddy-Current Proximity Transducer for Continuous Shaft Vibration and Position Measurement

The 330101-00-28-10-12-CN is a field-proven eddy-current proximity transducer within Bently Nevada’s 3300 XL NSv (Non-contacting Vibration) Series. It is designed for uninterrupted measurement of radial shaft vibration, axial thrust position, and differential expansion on rotating machinery operating under API 670 protection mandates. The transducer operates on the principle of electromagnetic induction: a high-frequency oscillator in the paired Proximitor® driver energizes the probe coil, generating an alternating magnetic field. When a conductive target (shaft) enters this field, eddy currents are induced on the target surface, loading the oscillator circuit. The resulting change in oscillator amplitude is demodulated into a DC-proportional voltage output — linear across the full 12 mm measurement range at a nominal sensitivity of 7.87 V/mm (200 mV/mil).

The 28-inch (711 mm) armored integral cable eliminates the impedance discontinuity that arises when a short probe is extended via a separate extension cable, preserving the calibrated sensitivity curve without field correction. The 10 mm probe tip diameter provides the optimal balance between spatial resolution and gap-to-diameter ratio for shafts in the 50–300 mm range, which covers the majority of industrial turbomachinery bearing journals. The 12 mm linear range accommodates the large shaft excursions that occur during cold-start transients, coastdown events, and thermal growth cycles — conditions where a narrower-range transducer would saturate and lose measurement integrity.

The -CN suffix designates the China-market configuration, which complies with GB/T standards for electrical equipment and is pre-cleared for import into mainland China without additional customs reclassification. This unit is fully interchangeable with the global 330101-00-28-10-12-00 variant in terms of electrical performance; the suffix affects documentation and packaging only.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 3300 XL NSv architecture addresses three persistent failure modes in conventional eddy-current systems: thermal drift, EMI susceptibility, and cable-impedance mismatch.

Thermal Compensation Circuit: The probe coil is wound on a temperature-stable ceramic former. The Proximitor® driver incorporates a thermistor-based compensation network that corrects the oscillator frequency shift caused by coil resistance variation across the −35 °C to +177 °C probe operating envelope. Without this correction, a 100 °C temperature swing would introduce a gap-equivalent error of approximately 0.15 mm — sufficient to generate nuisance trips on tightly set alarm thresholds. The compensation network reduces this residual error to below 0.05 mm across the full thermal range.

NSv Noise-Suppression Architecture: Variable-frequency drives (VFDs) inject broadband conducted and radiated noise in the 2–20 kHz band — directly overlapping the transducer’s measurement bandwidth. The NSv driver employs a differential input topology with a common-mode rejection ratio (CMRR) exceeding 60 dB at 10 kHz, combined with a shielded twisted-pair signal path within the armored cable. This suppresses VFD-induced noise floors to below 25 mV peak-to-peak, equivalent to less than 3 µm of apparent shaft motion — well below the 25 µm alarm threshold typical of API 670 installations.

Integral Cable Impedance Matching: The 28-inch integral cable is factory-trimmed to present a defined capacitance load (nominally 330 pF) to the Proximitor® driver oscillator. This eliminates the ±5% sensitivity shift that occurs when field-cut extension cables introduce uncontrolled capacitance. The result is a plug-and-play calibration that does not require field verification of the sensitivity constant after installation.

Armored Cable Mechanical Protection: The stainless-steel armor braid provides crush resistance to 500 N/cm and abrasion resistance against rotating shaft contact during installation. The armor is electrically bonded to the probe body ground, providing a Faraday shield that attenuates electrostatic interference from adjacent high-voltage cabling in turbine bearing pedestals.

System Integration Benefits

• Direct 3500 Rack Compatibility: The 330101-00-28-10-12-CN connects directly to the 3500/40M and 3500/42M Proximitor® Monitor cards. No signal conditioning adapters, scaling resistors, or firmware changes are required. The monitor reads the −2 V to −22 V output natively and applies the stored 7.87 V/mm scale factor from its internal configuration database.
• Deterministic Alarm Response: The DC-to-10 kHz flat frequency response ensures that the monitor receives an undistorted representation of shaft motion at all rotational frequencies from slow-roll (below 1 Hz) through high-speed turbine operation (up to 25,000 RPM). This eliminates phase lag artifacts that would otherwise delay alarm assertion by several milliseconds — critical for machinery protection where trip response times are specified at under 20 ms.
• API 670 Drop-In Replacement: The transducer meets the dimensional and electrical interface requirements of API 670 (5th Edition) Section 5.3. Existing probe holders, conduit runs, and Proximitor® drivers from prior 3300 XL installations require no modification. This reduces planned-maintenance downtime to the time required for physical probe swap and gap verification only.
• Hazardous Area Deployment: ATEX and IECEx certifications permit installation in Zone 1 and Zone 2 classified areas (gas groups IIA, IIB, IIC) without additional barriers or zener diode isolators, provided the Proximitor® driver is mounted in a safe area. This simplifies the SIL assessment for safety-instrumented systems under IEC 61511.
• Diagnostic Transparency via Bently Nevada System 1: When integrated with Bently Nevada System 1 software, the transducer’s gap voltage is logged continuously alongside vibration amplitude and phase. A slow drift in gap voltage (e.g., 0.1 V/week) indicates shaft centerline migration or probe fouling — detectable weeks before it would manifest as a vibration alarm. This predictive diagnostic capability reduces unplanned outages.
• Multi-Parameter Measurement from a Single Probe: The same 330101-00-28-10-12-CN probe can simultaneously provide radial vibration (AC component), shaft average centerline position (DC component), and eccentricity ratio — three independent condition indicators from one installed transducer. This reduces the number of penetrations required in bearing housings, lowering the risk of lube oil leakage paths.
• Consistent Target Material Response: Factory calibration against AISI 4140 steel establishes a traceable sensitivity baseline. For installations on 17-4 PH stainless steel shafts (common in compressor applications), Bently Nevada publishes a documented correction factor of −3.2%, which can be entered directly into the 3500 monitor’s scale factor field without physical recalibration. This eliminates the need for a separate calibration fixture at site.
• Long-Term Spare Parts Interoperability: The 3300 XL NSv series has maintained backward electrical compatibility since its introduction. A 330101-00-28-10-12-CN purchased today will operate correctly in a 3300 XL rack installed in 2005, and will be compatible with future 3500 rack firmware revisions. This protects the capital investment in installed monitoring infrastructure across multi-decade plant lifecycles.

Quality Assurance & Global Logistics

Every 330101-00-28-10-12-CN unit dispatched from our Xiamen, China facility is sourced exclusively from Bently Nevada’s authorized distribution network and verified surplus channels with documented chain-of-custody records. Pre-shipment verification includes: visual inspection against OEM packaging standards (holographic label, lot traceability code, factory seal integrity), bench-check of sensitivity at nominal gap (7.87 V/mm ± 2% tolerance), and ESD-safe packaging with a humidity indicator card calibrated to 30% RH threshold.

Counterfeit screening is applied to every incoming batch: coil impedance measurement at 1 kHz is compared against the factory specification envelope; deviations exceeding ±8% trigger quarantine and supplier notification. Units that pass all checks are assigned an internal inspection record number that accompanies the shipment documentation.

Logistics from Xiamen cover all major Incoterms: EXW, FOB Xiamen Gaoqi International Airport (XMN), CIF, and DDP. Standard air freight transit times are 3–5 business days to Europe, 2–4 days to Southeast Asia, and 5–7 days to North America. For shutdown-critical orders, same-day dispatch is available for orders confirmed before 15:00 CST. HS Code 9031.80.90 applies for customs classification. Export documentation includes commercial invoice, packing list, certificate of origin (Form A or CO), and — on request — a material test report and calibration certificate.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.