Bently Nevada 330102-00-80-10-02-00 Proximity Probe – 3300 XL Series

Bently Nevada 330102-00-80-10-02-00 — 8 mm Eddy-Current Proximity Probe in the 3300 XL Transducer System

The Bently Nevada 330102-00-80-10-02-00 is an 8 mm eddy-current proximity probe belonging to the 3300 XL Proximity Transducer System — a matched three-component architecture comprising probe, extension cable, and Proximitor® sensor. Within a rotating-machinery protection loop, this probe functions as the primary displacement transducer: it converts the gap between its tip and a conductive target surface into a proportional DC voltage, delivering a continuous, non-contact measurement of shaft radial position, orbital motion, and axial displacement. The output is linear across a calibrated range of 0.25 mm to 2.26 mm (10 mil to 89 mil), with a nominal scale factor of 7.87 V/mm (200 mV/mil) when paired with the matched 3300 XL Proximitor® driver. This deterministic transfer function is the foundation of API 670-compliant machinery protection: any deviation from the calibrated gap-voltage relationship is immediately interpretable as a mechanical event rather than an instrumentation artifact.

In a turbomachinery protection architecture, the 330102-00-80-10-02-00 is typically installed in orthogonal pairs at each radial bearing plane, separated by 90° (X–Y configuration), to resolve the full orbital trajectory of the shaft centerline. A third probe oriented axially monitors thrust position. The Bently Nevada 3500 Series Machinery Protection System receives these voltage signals, applies alarm and trip setpoints, and executes protective shutdown logic within deterministic scan cycles — typically under 20 ms from signal exceedance to relay actuation. The probe’s frequency response of DC to 10,000 Hz ensures that sub-synchronous instabilities, synchronous unbalance, and high-frequency rubs are all captured within the measurement bandwidth without aliasing.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The operating principle of the 330102-00-80-10-02-00 is governed by Faraday’s law of electromagnetic induction. The probe tip houses a precision-wound coil driven by a high-frequency oscillator (nominally 1.0 MHz) embedded in the paired Proximitor® sensor. This oscillator drives an alternating magnetic field that radiates from the coil face. When a conductive target enters the field, eddy currents are induced on the target surface; these eddy currents generate a counter-magnetic field that loads the oscillator circuit, reducing its amplitude in proportion to the gap distance. The Proximitor® demodulates this amplitude-modulated carrier into a DC voltage output — the gap signal — with a transfer function that is stable across the probe’s rated temperature range.

EMC Design: The armored coaxial cable construction provides continuous 360° shielding from the probe tip to the Proximitor® input, suppressing capacitively coupled interference from adjacent high-voltage cabling, variable-frequency drives, and ignition systems common in turbomachinery enclosures. The shield is grounded at the Proximitor® end only (single-point ground), eliminating ground-loop currents that would otherwise appear as low-frequency noise on the gap signal. The probe body is constructed from 316 stainless steel with a PEEK (polyether ether ketone) tip insert — a non-conductive, chemically resistant polymer that prevents the probe housing from acting as a secondary eddy-current target and ensures the measurement field geometry remains axially symmetric.

Thermal Stability: The coil winding uses a temperature-compensated formulation that maintains scale factor within ±1% across the full –35 °C to +177 °C operating range. This is critical in steam turbine applications where bearing housing temperatures can vary by 80–100 °C between cold startup and full-load steady state. Without thermal compensation, a scale factor drift of even 2% at a 1.5 mm operating gap would introduce a 30 µm position error — sufficient to mask an early-warning alarm threshold in a tightly configured protection system.

Matched-System Calibration: The 330102-00-80-10-02-00 is factory-calibrated as part of a matched set with a specific extension cable (330130 Series) and Proximitor® sensor (330180 Series). The calibration data — scale factor, bias voltage, and linearity coefficients — are recorded against the serial numbers of all three components. Substituting any single component from a different matched set degrades the system accuracy and voids the API 670 calibration traceability. This architecture enforces a discipline that prevents field-substitution errors from introducing undetected measurement bias into a protection system.

System Integration Benefits

• Non-contact measurement eliminates wear-induced drift: Unlike contact-type displacement sensors, the eddy-current probe has no mechanical interface with the rotating shaft. There is no stylus wear, no friction-induced hysteresis, and no lubrication requirement — the measurement characteristic remains stable over the full service life of the probe, which in clean environments routinely exceeds 10 years of continuous operation.
• DC-coupled output preserves static position data: The DC-to-10,000 Hz bandwidth means the output voltage represents absolute gap, not just AC vibration. This allows the 3500 system to monitor both dynamic vibration amplitude and static shaft centerline position simultaneously from a single probe — enabling detection of bearing wear (gradual centerline shift) alongside acute vibration events.
• Deterministic latency supports sub-20 ms trip logic: The probe’s analog output has no digital processing latency. The Proximitor® output is a continuous analog voltage that the 3500 rack samples at its full scan rate. Combined with the 3500’s hardware-based trip logic, the end-to-end latency from a mechanical event to relay actuation is deterministic and independent of software scheduling — a requirement for API 670 compliance in critical service.
• Orthogonal pair installation resolves full orbital trajectory: Two probes at 90° separation at each bearing plane allow the 3500 system to compute the shaft centerline orbit in real time. This two-dimensional position data distinguishes between circular orbits (unbalance), elliptical orbits (misalignment), and figure-eight orbits (rub or instability) — providing diagnostic information that a single-axis measurement cannot deliver.
• High-frequency response captures rub and instability events: The 10,000 Hz upper bandwidth captures shaft rub signatures (typically 3×–10× running speed harmonics) and fluid-film instabilities (sub-synchronous, 0.3×–0.5× running speed) that are invisible to lower-bandwidth sensors. Early detection of these phenomena allows operators to reduce load or initiate a controlled shutdown before catastrophic bearing failure.
• Integral cable eliminates connector-interface noise: The 5 m integral armored cable removes the field-installed connector junction between probe and extension cable that exists in some competitive designs. Connector interfaces are a known source of intermittent contact resistance, which manifests as high-frequency noise spikes on the gap signal — a particularly problematic artifact in machinery protection systems where spike detection can trigger spurious trips.
• PEEK tip material resists process fluid contamination: In wet-gas compressors and steam turbines, the probe tip is exposed to condensate, lube oil mist, and process gas. PEEK’s chemical resistance to hydrocarbons, steam, and common industrial solvents prevents tip degradation that would alter the dielectric environment around the coil and shift the effective scale factor over time.
• API 670 compliance simplifies insurance and regulatory acceptance: Specifying an API 670-compliant transducer system eliminates the need for project-specific engineering justification of the measurement system. Insurance underwriters, plant safety authorities, and EPC contractors accept API 670 compliance as a baseline qualification — reducing project schedule risk associated with instrumentation review cycles.

Quality Assurance & Global Logistics

Every Bently Nevada 330102-00-80-10-02-00 unit supplied by siemensplc.com is sourced through established industrial distribution channels and subjected to a structured incoming inspection protocol before dispatch. Physical inspection covers probe body integrity, tip surface condition, cable jacket continuity, connector seating, and part number label verification against Bently Nevada factory markings. Units that exhibit any evidence of mechanical damage, label inconsistency, or non-standard packaging are quarantined and excluded from shipment.

Our warehouse is located in Xiamen, China — a major international logistics hub with direct access to DHL Express, FedEx International Priority, and UPS Worldwide Expedited services. Standard in-stock orders are dispatched within 1–3 business days of payment confirmation. For urgent requirements, same-day dispatch is available on orders confirmed before 14:00 CST. Export documentation — commercial invoice, packing list, certificate of origin, and HS code 9031.80 classification — is prepared in-house and transmitted to the freight forwarder simultaneously with dispatch, minimizing customs clearance delays at destination ports. We serve industrial buyers across Asia-Pacific, the Middle East, Europe, and the Americas, with a track record of on-time delivery to remote plant sites including offshore platforms and desert installations.

All units are shipped in anti-static, moisture-barrier packaging with foam-lined outer cartons rated for international air freight handling. The 12-month warranty covers manufacturing defects identified upon receipt and confirmed through our technical review process. Warranty claims are processed within 5 business days of receipt of the returned unit.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.