Bently Nevada 330103-00-02-10-02-00 Proximity Probe – 3300 XL

Bently Nevada 330103-00-02-10-02-00: Eddy-Current Proximity Probe for API 670 Machinery Protection

The Bently Nevada 330103-00-02-10-02-00 is an 8 mm eddy-current proximity probe designed as the primary sensing element within the 3300 XL Proximity Transducer System. Its operational mandate within any API 670-compliant machinery protection architecture is precise: deliver a continuous, low-noise DC voltage signal proportional to the instantaneous air gap between the probe tip and a rotating shaft surface, with a nominal sensitivity of 7.87 V/mm (200 mV/mil) across a calibrated linear range of 0.25 mm to 2.54 mm (10 to 100 mil). This analog output feeds the paired Proximitor® sensor, which conditions and transmits the signal to a monitoring rack — typically a Bently Nevada 3500 Series system — where radial vibration amplitude, shaft centerline position, and dynamic runout are computed in real time.

In rotating machinery protection, the proximity probe occupies the first position in a measurement chain whose output directly governs machine trip and alarm logic. Any degradation in probe linearity, thermal drift, or connector integrity propagates without attenuation into the monitoring system’s decision layer. The 330103-00-02-10-02-00 addresses each of these failure vectors through its physical construction: a hermetically sealed stainless-steel body with a factory-terminated 2.0-meter integral cable, eliminating the field-splice junction that statistical maintenance records identify as the highest-frequency failure point in eddy-current transducer installations. The integral cable assembly is rated for continuous operation from −18 °C to +177 °C, covering the full thermal envelope of hot-section installations adjacent to turbine casings, exhaust manifolds, and steam chest flanges.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330103-00-02-10-02-00 operates on the principle of high-frequency eddy-current induction. The probe’s internal coil, driven by an oscillator circuit within the paired Proximitor® sensor at approximately 1 MHz, generates an alternating electromagnetic field at the probe tip. When a conductive target enters this field, eddy currents are induced on the target surface, loading the oscillator and attenuating the coil’s resonant amplitude. The Proximitor® demodulates this amplitude change into a DC voltage output — the gap signal — with a transfer function that is linear within the specified measurement range.

EMC Architecture: The stainless-steel probe body functions as a continuous Faraday enclosure, attenuating external electromagnetic interference from adjacent variable-frequency drives, high-current bus bars, and switchgear common in turbomachinery installations. The coaxial geometry of the integral cable maintains a consistent characteristic impedance along the full 2-meter run, preventing reflective signal distortion. This is operationally significant in installations where probe cables share cable trays with power conductors — a configuration that would introduce measurable noise into a non-shielded measurement lead.

Thermal Coefficient Management: The coil winding material and encapsulating compound are selected for a low thermal coefficient of inductance. Across the rated −18 °C to +177 °C operating range, sensitivity deviation remains within the system’s published calibration tolerance. This means a Proximitor® calibration performed at ambient temperature remains valid at elevated operating temperatures without field recalibration — a critical requirement for steam turbine installations where probe body temperatures routinely reach 140–160 °C during normal load operation.

Integral Cable Reliability Logic: The factory-terminated integral cable eliminates the field-installed junction between probe body and extension cable. In conventional two-piece installations, this junction — when exposed to vibration, thermal cycling, and moisture ingress — is the statistically dominant failure mode in eddy-current transducer systems. By relocating this junction to a controlled factory environment with engineered strain relief and environmental sealing, the 330103-00-02-10-02-00 removes the primary source of intermittent signal faults that are characteristically difficult to diagnose during machine operation.

Target Material Correction: The probe is factory-calibrated against AISI 4140 steel targets. Installations on shafts of differing alloy composition — 17-4 PH stainless steel, Inconel 718, or titanium alloys — require application of the appropriate material correction factor from Bently Nevada’s published calibration data to maintain measurement accuracy within ±1% of full-scale range. This correction is applied at the Proximitor® or monitoring rack level and does not require physical modification of the probe.

System Integration Benefits

• API 670 Compliance Without Additional Qualification: The 330103-00-02-10-02-00 meets the transducer performance requirements of API Standard 670 (5th Edition) as shipped, satisfying insurance underwriter, regulatory authority, and OEM acceptance criteria without supplementary testing or documentation.
• Zero-Reconfiguration Drop-In Replacement: Electrically and mechanically interchangeable with all 3300 XL 8mm probe variants of equivalent cable length. Replacement requires no Proximitor® recalibration, no rack parameter modification, and no system downtime beyond the physical swap — provided total system cable length remains within the Proximitor’s calibration range.
• Deterministic Measurement Latency: The eddy-current measurement chain introduces no sampling delay beyond the Proximitor’s analog output settling time, typically under 1 ms. This deterministic latency is a hard requirement for machinery protection systems where trip response time is contractually specified in milliseconds.
• Dual-Parameter Single-Probe Architecture: One probe installation simultaneously delivers radial vibration data (dynamic AC component) and shaft centerline position data (DC component), reducing the number of bearing housing penetrations required and simplifying installation in space-constrained bearing pedestals.
• Continuous Gap Health Monitoring: The DC gap voltage output provides a real-time, observable health indicator for the probe-shaft system. A gap voltage outside the linear range is immediately visible on the monitoring system display, enabling maintenance personnel to identify probe mounting drift or shaft displacement before measurement accuracy is compromised.
• 3500 Series Rack Compatibility: Output characteristics are fully compatible with Bently Nevada 3500/40M, 3500/42M, and 3500/46M monitor modules, enabling integration into existing 3500 Series machinery protection racks without hardware modification or firmware update.
• Extended Calibration Intervals: Non-contact measurement eliminates mechanical wear on both probe tip and shaft surface. In continuous-duty applications operating 8,760 hours per year, service life is governed by cable fatigue and connector integrity rather than tip wear, typically extending calibration intervals to 24–48 months in thermally stable installations.
• Hazardous Area Deployment Capability: When paired with an appropriate Proximitor® sensor and installed per Bently Nevada’s hazardous area installation guidelines, the system supports deployment in Zone 1/Zone 2 (ATEX) and Class I Division 1/2 (NEC) classified areas, covering the majority of oil and gas processing and petrochemical plant environments.
• Diagnostic Transparency at System Level: The analog output architecture allows any standard oscilloscope or data acquisition system to directly observe the raw gap signal, enabling field engineers to perform independent signal verification without proprietary diagnostic tools — a significant advantage during commissioning and fault investigation.

Quality Assurance & Global Logistics

Every Bently Nevada 330103-00-02-10-02-00 unit dispatched from our Xiamen, China facility undergoes a structured pre-shipment verification protocol. Physical inspection covers probe body integrity, cable jacket condition, connector pin alignment, and thread condition on the probe body. Part number and date code are cross-referenced against manufacturer documentation to confirm authenticity and production batch traceability. Units are packaged in anti-static foam-lined cartons with desiccant packs and humidity indicator cards, preserving the probe’s electrical characteristics during long-haul ocean or air freight transit.

From Xiamen, we ship to industrial facilities across Southeast Asia, the Middle East, Europe, and the Americas. Standard air freight transit times are 3–7 business days to most destinations. For urgent requirements, same-day dispatch on in-stock units is available for orders confirmed before 14:00 CST. Export documentation — commercial invoice, packing list, certificate of origin, and MSDS where applicable — is prepared in-house, eliminating third-party documentation delays. DDP, DAP, and EXW Incoterms are all supported. All units carry a 12-month warranty from the shipment date, covering manufacturing defects and electrical performance deviations from published specifications.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.