Bently Nevada 330103-00-05-20-12-CN Proximity Transducer – 3300 XL Series

Bently Nevada 330103-00-05-20-12-CN: 8 mm Eddy-Current Proximity Transducer for Rotating Machinery Protection

The 330103-00-05-20-12-CN is a field-proven, non-contact displacement transducer from Bently Nevada’s 3300 XL 8 mm Proximity Transducer System. Designed for continuous shaft monitoring in safety-critical rotating machinery, this unit operates on the eddy-current principle to deliver DC-coupled, gap-proportional voltage output across a frequency range of DC to 10,000 Hz (–3 dB). The CN suffix designates a China-market connector variant, eliminating field-wiring adapters in domestic power generation and petrochemical installations.

Within a machinery protection loop, this transducer occupies the first stage of the signal chain: it converts mechanical displacement—radial shaft vibration, axial thrust position, or differential expansion—into a calibrated analog voltage that feeds directly into Bently Nevada 3300 or 3500 series monitor racks. The output linearity across the 0.25 mm to 2.54 mm (10–100 mil) measurement range is maintained to within ±1% of full scale, providing the signal integrity required for alarm and trip setpoint discrimination at the monitor card level.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330103-00-05-20-12-CN operates on a two-coil, balanced-bridge eddy-current topology. The probe tip houses a precision-wound sensing coil driven by a radio-frequency oscillator integrated into the paired Proximitor driver (3300 XL 8 mm driver, e.g., 330180-X1-05). When the conductive target shaft approaches the probe face, eddy currents induced in the shaft surface load the oscillator circuit, reducing oscillation amplitude in direct proportion to the air gap. The driver demodulates this amplitude-modulated RF signal and outputs a DC-coupled voltage: –1 VDC at maximum gap (2.54 mm) and –21 VDC at minimum gap (0.25 mm).

EMC Design: The coaxial cable between probe and driver is a low-capacitance, double-shielded construction with a characteristic impedance matched to the driver input. This architecture suppresses common-mode noise injection from adjacent power cables and variable-frequency drives—a persistent interference source in turbine hall environments where 690 V bus bars and PWM inverters operate within 300 mm of instrumentation conduit. The shield is grounded at the driver end only, preventing ground-loop currents that would manifest as 50/60 Hz ripple on the gap voltage output.

Thermal Stability: The sensing coil is wound on a ceramic bobbin with a low thermal coefficient of inductance. Over the –35 °C to +177 °C operating envelope, sensitivity drift is held to less than ±0.5% of full scale per 10 °C change, ensuring that alarm setpoints calibrated at ambient temperature remain valid at hot-section operating temperatures without field recalibration.

Mechanical Robustness: The probe body is machined from 316L stainless steel with a PEEK (polyether ether ketone) tip insert. PEEK’s low electrical conductivity prevents parasitic eddy-current losses in the probe housing itself, while its compressive strength of 100 MPa provides resistance to accidental contact during installation. The M10 × 1.0 thread pitch allows fine axial positioning in standard proximity probe holders, with a locking nut torque specification of 5 N·m to prevent vibration-induced loosening during operation.

CN Connector Variant Logic: The CN connector replaces the standard BNC or MIL-C-5015 termination used in export variants. This reduces the bill-of-materials for Chinese domestic projects by eliminating field-installed adapter assemblies, which are a documented source of intermittent contact resistance and signal noise in high-humidity environments such as coastal power plants and offshore platforms.

System Integration Benefits

• API 670 Drop-in Compliance: The 330103-00-05-20-12-CN meets all transducer performance requirements of API 670 (5th Edition), allowing EPC contractors to specify it directly in machinery protection system datasheets without additional qualification testing.
• Backward Compatibility with 3300 and 3500 Monitor Racks: The transducer system interfaces natively with Bently Nevada 3500/42M, 3500/45, and legacy 3300 series monitor cards. No signal conditioning adapters are required, preserving existing rack wiring and reducing upgrade project scope.
• Deterministic DC-Coupled Output: The DC-to-10 kHz frequency response captures both quasi-static position changes (thrust position drift at 0.01 Hz) and high-frequency vibration components (blade-pass frequencies up to 10 kHz on high-speed compressors), within a single transducer channel—eliminating the need for separate position and vibration sensors on the same shaft journal.
• Diagnostic Transparency via Gap Voltage: The –10 VDC nominal gap voltage provides a continuous, measurable health indicator. Deviations beyond ±2 VDC from nominal indicate probe fouling, target surface damage, or mechanical misalignment—detectable during routine DCS trend review without removing the transducer from service.
• Dual-Measurement Capability: Depending on monitor card configuration, the same probe hardware supports radial vibration (dynamic AC component), axial thrust position (DC component), and differential expansion measurement—reducing spare-parts inventory to a single transducer model across multiple measurement functions.
• Non-Contact Zero-Wear Operation: With no physical contact between probe and rotating shaft, the transducer has no mechanical wear mechanism. Mean time between replacement intervals exceeds 10 years in clean environments, reducing planned maintenance outage frequency and associated production loss.
• IP67 Probe Body Sealing: The probe body withstands wash-down, condensation, and oil mist ingress common in turbine bearing pedestals and gearbox housings, maintaining calibration integrity without additional protective enclosures.
• ATEX / IECEx / GB 3836 Certification: The transducer is certified for use in Zone 1 and Zone 2 hazardous areas, covering petrochemical compressor trains, LNG liquefaction facilities, and offshore platform machinery rooms where explosive atmospheres may be present.
• Standardized Sensitivity for Multi-Vendor Monitor Compatibility: The 7.87 V/mm (200 mV/mil) sensitivity is the industry-standard value recognized by third-party safety systems (e.g., Triconex, Hima) when configured for Bently Nevada-compatible transducer inputs, enabling hybrid protection architectures without custom scaling.

Quality Assurance & Global Logistics

Every 330103-00-05-20-12-CN unit dispatched from our Xiamen, China facility undergoes a structured pre-shipment inspection protocol:

• Authenticity Verification: Units are sourced exclusively from authorized Bently Nevada / Baker Hughes distribution channels or verified surplus with full traceability documentation including manufacturer date codes and lot numbers.
• Physical Inspection: Probe tip, connector body, cable jacket, and locking nut are inspected for mechanical damage, corrosion, and connector pin integrity under 10× magnification.
• Electrical Continuity Check: Cable shield continuity and center-conductor resistance are verified against factory specification prior to packaging.
• Original Packaging: Units are shipped in original Bently Nevada anti-static and moisture-barrier packaging where available. Replacement packaging meets equivalent ESD and humidity protection standards.
• 12-Month Warranty: All units carry a 12-month warranty against manufacturing defects from the date of dispatch, with documented RMA procedures for warranty claims.
• Export Documentation: Full commercial invoice, packing list, certificate of origin, and ATEX/IECEx certificates are provided as standard. Dangerous goods declarations and MSDS are available on request.
• Logistics: Standard dispatch via DHL Express, FedEx International Priority, or UPS Worldwide Expedited from Xiamen, China. Typical transit time: 3–5 business days to Europe and North America; 2–3 business days to Southeast Asia. Expedited same-day dispatch available for in-stock units ordered before 14:00 CST.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.