Bently Nevada 330103-15-23-10-02-00 Proximity Transducer System – 3300 XL

Bently Nevada 330103-15-23-10-02-00 — Eddy-Current Proximity Transducer System for Rotating Machinery Protection

The Bently Nevada 330103-15-23-10-02-00 is a factory-matched, three-component eddy-current proximity transducer system belonging to the 3300 XL 8 mm platform. It is engineered for continuous, non-contact measurement of shaft radial vibration, axial position, and differential expansion in critical rotating machinery. The system consists of a probe, an armored extension cable, and a Proximitor® driver/oscillator-demodulator — all calibrated as a matched set at the factory to ensure scale-factor traceability across the full measurement range.

In a machinery protection architecture, this transducer system occupies the first link in the signal chain: it converts mechanical gap displacement into a proportional DC voltage that feeds directly into Bently Nevada 3300 or 3500 Series monitoring racks, or into any DCS/PLC analog input card accepting a –24 VDC-referenced voltage signal. The 200 mV/mil (7.87 V/mm) scale factor is the industry-standard output for eddy-current proximity systems, ensuring interoperability with legacy and modern monitoring platforms without signal-conditioning adapters.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330103-15-23-10-02-00 operates on the eddy-current (electromagnetic induction) principle. The Proximitor driver generates a high-frequency oscillation — nominally 1.0 MHz — through the probe coil. When a conductive target (shaft) enters the probe’s electromagnetic field, eddy currents are induced on the target surface, loading the oscillator circuit and reducing its amplitude. The driver’s demodulator converts this amplitude change into a proportional DC voltage output, yielding a linear relationship between gap distance and output voltage across the 2.0 mm measurement span.

EMC and Shielding Architecture: The extension cable uses a double-layer armored construction with an inner coaxial shield and an outer braided armor. This geometry suppresses both capacitive coupling from adjacent power conductors and inductive pickup from motor drive harmonics — a critical design requirement in turbine halls where variable-frequency drives and high-current bus bars operate in close proximity to instrumentation cabling. The Proximitor driver enclosure is constructed from die-cast aluminum with continuous EMI gasket sealing, achieving shielding effectiveness exceeding 60 dB across the 10 kHz – 1 GHz band.

Matched-Set Calibration Logic: The probe, extension cable, and driver are calibrated as a system, not as individual components. The cable’s distributed capacitance and inductance are characterized and compensated within the driver’s oscillator tuning network. Substituting any single component from a different matched set introduces a scale-factor error that is not correctable by rack-level gain adjustment alone. This is why the 330103-15-23-10-02-00 part number encodes the complete system configuration — the trailing digits specify probe cable length (15 cm), extension cable length (2.3 m), and driver variant — ensuring field engineers receive a pre-validated assembly.

Frequency Response and Shaft Dynamics: The DC-coupled, 10,000 Hz bandwidth allows the system to resolve not only synchronous (1×) and sub-synchronous vibration components but also high-frequency structural resonances and blade-passing frequencies in compressors. At 10,000 Hz, the system can accurately characterize shaft motion at speeds exceeding 600,000 RPM for 1× components, well beyond the operating envelope of any industrial rotating machine. In practice, this bandwidth margin ensures that the system does not attenuate or phase-shift the vibration signal within the machinery protection rack’s alarm-processing window.

System Integration Benefits

• Direct rack compatibility: The 7.87 V/mm output is natively accepted by Bently Nevada 3300 and 3500 Series monitor cards without signal conditioning, eliminating an entire tier of analog circuitry and its associated failure modes.
• API 670 compliance out of the box: The system meets the measurement accuracy, frequency response, and temperature requirements of API 670 Fifth Edition, simplifying plant acceptance testing and third-party audits without additional documentation burden.
• Non-contact measurement eliminates wear: With zero mechanical contact between probe and shaft, the transducer’s measurement accuracy does not degrade with shaft revolutions. A probe installed on a 3,000 RPM machine accumulates 1.58 billion shaft passes per year with no measurable change in scale factor.
• Deterministic signal latency: The analog output path from gap change to voltage output has a propagation delay below 100 µs, ensuring that the monitoring rack receives vibration data within one shaft revolution at speeds as low as 600 RPM — a requirement for reliable trip response in API 670 protection systems.
• Hazardous-area deployment without additional barriers: ATEX and FM intrinsic safety approvals allow direct installation in Zone 1 / Class I Division 1 environments in many configurations, reducing the bill of materials for Zener barrier or galvanic isolator assemblies.
• Diagnostic transparency via gap voltage: The DC component of the output voltage directly encodes the average probe-to-shaft gap. Operators can monitor gap drift over time to detect shaft centerline migration, bearing wear, or probe mounting looseness — all without interrupting production.
• Wide operating temperature range: The probe’s –35 °C to +121 °C rating covers both arctic outdoor installations and high-temperature bearing housings on steam turbines, eliminating the need for thermal management accessories in most applications.
• Interoperability with third-party DCS/PLC inputs: The –24 VDC-referenced voltage output is compatible with any analog input card accepting a high-impedance voltage signal. Integration into ABB, Emerson, Yokogawa, or Siemens DCS platforms requires only a passive voltage divider or differential input card — no active signal conversion.

Quality Assurance & Global Logistics

Every 330103-15-23-10-02-00 unit dispatched from our Xiamen facility undergoes a structured pre-shipment inspection protocol:

• Visual inspection of probe tip geometry, cable jacket integrity, and MIL-C-5015 connector pin condition
• Continuity and insulation resistance verification on probe coil and extension cable shield
• Gap voltage output measurement at 1.27 mm gap against the factory scale-factor specification (–10.0 VDC ± 0.5 VDC)
• Serial number cross-reference against procurement documentation
• Anti-static packaging with humidity indicator card and shock-watch label for transit monitoring

Units are sourced from authorized distribution channels and verified surplus inventories with full traceability documentation. A Certificate of Conformance (CoC) is available upon request. All export shipments from Xiamen, China are handled via DHL Express, FedEx International Priority, or UPS Worldwide Expedited, with typical transit times of 3–7 business days to Europe, North America, Southeast Asia, and the Middle East. Customs documentation, including commercial invoice, packing list, and HS code declaration (HS 9031.80), is prepared in-house to minimize clearance delays. The 12-month warranty covers manufacturing defects and scale-factor deviation beyond the published tolerance; field damage and incorrect installation are excluded.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.