Bently Nevada 330104-00-07-90-02-00 Proximity Transducer – 3300 XL 8mm

Bently Nevada 330104-00-07-90-02-00 — Armored 8mm Eddy-Current Proximity Transducer for Rotating Machinery Protection

The Bently Nevada 330104-00-07-90-02-00 is a field-proven, non-contact eddy-current proximity transducer belonging to the 3300 XL 8mm Series. It is designed for continuous shaft radial vibration and axial position measurement in high-speed rotating machinery operating under API 670 protection mandates. The probe integrates a 0.9 m integral cable terminated with a 2-pin MIL-C-5015 connector and is enclosed in a 90-series stainless steel armored jacket — a configuration optimized for installations where cable routing passes through mechanically aggressive zones such as turbine pedestals, compressor skids, and gearbox housings.

Unlike general-purpose inductive sensors, the 3300 XL platform is calibrated as a matched three-component system: probe, extension cable, and Proximitor® driver. The 330104-00-07-90-02-00 is the probe element of this system, delivering a linear output range of 2.54 mm (100 mil) with a scale factor of 7.87 V/mm (200 mV/mil) — the industry-standard sensitivity for machinery protection monitors. This output is directly compatible with Bently Nevada 3500/40M and 3300/16 monitor modules without signal conditioning adapters.

Deployment environments include steam and gas turbines in power generation, centrifugal and axial compressors in LNG and petrochemical plants, hydro turbines, marine propulsion shafting, and high-speed gearboxes. The probe’s operating temperature ceiling of 177°C at the tip permits installation in hot-section turbine bearing housings where conventional sensors fail prematurely.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330104-00-07-90-02-00 operates on the eddy-current (electromagnetic induction) principle. The probe tip houses a flat coil driven by a high-frequency oscillator within the Proximitor® driver, typically at 1.0 MHz. When the conductive target (shaft) enters the probe’s electromagnetic field, eddy currents are induced on the shaft surface, loading the oscillator circuit and reducing its amplitude. This amplitude modulation is demodulated into a DC voltage proportional to the gap distance between probe tip and shaft surface.

EMC Design: The 90-series armor provides a continuous Faraday shield along the cable run, attenuating radiated electromagnetic interference from variable-frequency drives, high-current bus bars, and RF sources common in industrial plants. The MIL-C-5015 connector’s metal shell maintains shield continuity at the junction box interface — a detail that generic M12 connectors cannot replicate at high frequencies.

Thermal Stability: The probe coil is wound on a ceramic bobbin with a low thermal expansion coefficient. This minimizes gap-reading drift across the probe’s 212°C operating temperature span. In hot-section turbine installations where bearing housing temperatures can exceed 150°C, this thermal stability is the primary reason engineers specify the 3300 XL over lower-rated alternatives.

Matched-System Calibration Logic: The 3300 XL system is calibrated as a matched set. The Proximitor® driver’s internal compensation network is tuned to the specific probe and extension cable impedance. Substituting a non-matched extension cable introduces a gain error that shifts the scale factor away from 7.87 V/mm — an error that propagates directly into vibration amplitude readings and can cause nuisance trips or, worse, missed alarm thresholds. The suffix encoding in the part number (00-07-90-02-00) encodes cable length, armor type, and connector variant, ensuring procurement teams order the correct matched component.

Non-Contact Measurement Advantage: Because the probe never contacts the shaft, there is zero mechanical wear, no lubrication requirement, and no measurement artifact from probe-to-shaft friction. The sensor responds to true shaft centerline displacement, capturing both synchronous (1X) and sub-synchronous vibration components that contact-type sensors cannot resolve at high shaft speeds.

System Integration Benefits

• API 670 Fifth Edition Compliance: The 3300 XL system meets the full requirements of API 670 for radial vibration and axial position channels, satisfying EPC contractor and end-user specifications without additional engineering justification.
• Direct Monitor Compatibility: Output signal (–1 to –21 VDC, 200 mV/mil) interfaces directly with Bently Nevada 3500/40M, 3300/16, and System 1 software without signal conditioning modules, reducing panel wiring complexity.
• Deterministic Frequency Response to 10 kHz: The flat frequency response from DC to 10,000 Hz captures shaft dynamic events including gear mesh frequencies, blade-pass frequencies, and oil whirl instabilities — all within a single sensor channel.
• ATEX Zone 1 Certification: The probe is certified for use in Group IIC, Zone 1 hazardous areas when paired with an approved Zener barrier or galvanic isolator, enabling deployment in hydrogen-rich and solvent-handling environments without additional enclosure engineering.
• Backward Compatibility with 3300 Series Infrastructure: Existing 3300/16 monitor racks, junction boxes, and cable trays can accept the 3300 XL probe without modification, protecting prior capital investment during plant upgrades.
• Diagnostic Transparency via System 1: When connected to Bently Nevada System 1 software, the probe channel provides full waveform, spectrum, and orbit plot data — enabling root-cause analysis of rotor dynamic faults without additional instrumentation.
• Armored Cable for Harsh Routing: The 90-series stainless steel armor withstands mechanical abrasion, rodent damage, and incidental impact loads during maintenance activities, reducing unplanned sensor replacement events in operating plants.
• Wide Supply Voltage Tolerance (–18 to –26 VDC): The system maintains calibrated output across a ±4 V supply variation, accommodating voltage drops in long cable runs from remote power supplies without recalibration.

Quality Assurance & Global Logistics

Every Bently Nevada 330104-00-07-90-02-00 unit supplied by siemensplc.com is sourced through verified industrial distribution channels and undergoes a structured incoming inspection protocol before dispatch:

• Visual inspection of probe tip, armor jacket, and MIL connector for mechanical integrity
• Continuity verification of probe coil and shield conductor
• Insulation resistance check between signal conductors and armor
• Review of available OEM documentation and batch traceability records
• Anti-static, moisture-barrier packaging with desiccant for international transit

All units carry a 12-month warranty from the date of shipment. Warranty coverage addresses manufacturing defects and calibration non-conformance. Units are clearly labeled by condition (new, new-old-stock, or refurbished) at the time of quotation.

Shipments originate from Xiamen, China. Standard international delivery via DHL Express or FedEx International Priority reaches most destinations within 3–7 business days. Expedited same-day dispatch is available for in-stock units when orders are confirmed before 14:00 CST. Export documentation including commercial invoice, packing list, and HS code declaration (HS 9031.80) is prepared for all international shipments to facilitate customs clearance.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.